How to Steer When the Rear of the Car Veers to the Right While Reversing into a Parking Space?

2 Answers
VonJake
09/07/25 8:04am
If the rear of the car veers to the right, steer to the left. When the car body straightens, return the steering wheel to the center position. Based on the rear of the car, if you want the rear to move closer to the right, turn the steering wheel to the right; if the rear veers to the left, steer to the left, then return the steering wheel in the opposite direction to straighten the car.
Was this review help?
19
5
Share
Kathleen
09/19/25 7:05am
When I usually reverse into a parking spot, I'm most afraid of the car's rear swinging to the right. Let me get straight to the point: at this moment, you should turn the steering wheel to the left. Don't get the direction wrong—I used to make that mistake a lot when I first started learning to drive. Turning the steering wheel to the left actually helps the car's rear move back to the left. Remember not to correct the angle too much; about half a turn is enough. Turning too much will make the rear swing too far to the left. It's best to make slight adjustments while keeping an eye on the left and right rearview mirrors, and be sure to go slow! If the wheels are about to touch the line and you still can't adjust in time, it's better to drive forward a bit and start reversing again. Forcing it might scratch the rims. Practice a few more times to get the hang of it—the relationship between the car's rear and the parking line in the rearview mirror is the most intuitive.
Was this review help?
13
0
Share
Expand All
More Forum Discussions

Is Engine Oil Leak Covered Under Warranty?

Engine oil seal leakage falls within the three-year warranty period. The reasons for Passat engine oil leakage are as follows: Aging and hardening of sealing rings: Over 90% of oil leakage issues are caused by rubber sealing rings losing a significant amount of plasticizers and softeners due to prolonged exposure to alternating cold and warm temperatures, leading to corrosion, aging, and hardening problems. Incomplete combustion: Small fuel injection advance angle, incomplete combustion, slight water leakage in cylinder liners, water content in fuel, white smoke emission during cold starts which disappears as engine temperature rises. Smoke limiter failure: Air-fuel ratio imbalance, decreased cylinder pressure, premature fuel injection timing, failure of smoke limiter on fuel injection pump, malfunctioning exhaust brake system, engine cylinder liner wear, piston ring sticking, misalignment, aging and deformation of valve sealing rings, excessive valve guide clearance.
19
5
Share

Replacement Cycle for Magotan Transmission Control Unit?

The replacement cycle for the Magotan transmission control unit is every 3 years. Transmission: The transmission is a mechanism used to change the speed and torque from the engine. It can fix or change the transmission ratio between the output shaft and the input shaft in steps, also known as the gearbox. The transmission consists of a transmission mechanism and a control mechanism, and some vehicles also have a power output mechanism. The transmission mechanism mostly uses ordinary gear transmission, while some use planetary gears. Replacement Cycle: Remove the positioning screws, washers, springs, steel balls, and reverse light switch. Remove the shift control device and positioning pins. Remove the drain plug, fill plug, and vehicle speed sensor. Remove the transmission hanger. Cross and remove the transmission housing bolts in three steps. Remove the sealing screws. Spread the retaining ring and place it on the countershaft bearing, then remove it with a retaining ring pliers. Finally, pull out the transmission housing and positioning pins.
2
5
Share

Why Does the Rear Wheel Make Abnormal Noise When the Motorcycle Carries Two People?

Abnormal noise from the rear wheel when the motorcycle carries two people may be caused by insufficient lubrication of the wheel hub bearings, unstable tire pressure, or aging of the shock absorber bushings. Pay attention to tire pressure: Pressure is the lifeblood of a tire. Both too high and too low pressure will shorten its service life. If the pressure is too low, the tire body deformation increases, cracks are prone to appear on the tire side, and flexing motion occurs, leading to excessive heat generation, promoting rubber aging, fatigue of the cord layer, and cord breakage. Low pressure also increases the tire's contact area, accelerating wear on the tire shoulder. Excessive pressure causes the tire cords to be overstretched and deformed, reducing the tire body's elasticity and increasing the load the vehicle bears while driving. Regularly check front wheel alignment: Front wheel alignment significantly affects tire lifespan, with toe-in and camber being the main factors. Camber mainly accelerates shoulder wear, i.e., uneven wear, while incorrect toe-in (too large or too small) primarily accelerates wear on the inner and outer sides of the tire.
10
2
Share

Are all new vehicles exempt from inspection when being registered?

Newly registered vehicles are exempt from inspection for six years, but this only applies to non-commercial vehicles with seven seats or fewer. However, owners still need to collect the inspection sticker within each cycle (once every two years), which can now be done online. For newly registered small private passenger vehicles: They are exempt from on-site inspection for six years, but owners must still apply for the annual inspection and environmental labels on time (once every two years within the six-year period). This applies to non-commercial small private passenger vehicles with fewer than seven seats registered after August 31, 2010. No on-site inspection required for six years: According to the new regulations, no on-site inspection is required for six years. However, owners must still provide proof of compulsory traffic accident liability insurance, proof of vehicle and vessel tax payment or exemption, and resolve any traffic violations or accidents before applying for the inspection sticker directly from the traffic management department. (The vehicle must not have been involved in any fatal accidents during this period.) After six years, on-site inspection is required.
4
3
Share

Is it normal for a new automatic transmission car to make noise when stepping on the brake and turning the steering wheel?

It is normal for a new automatic transmission car to make noise when stepping on the brake and turning the steering wheel. This could be due to the break-in period of the new car, or it might be caused by sand particles getting between the brake pads and discs, resulting in friction noise. Automatic transmission gear classifications: Generally, the gears of an automatic transmission car can be divided into P, R, N, D, S, L, and M gears. Precautions for driving an automatic transmission car: Driving an automatic transmission car using only the parking gear P, reverse gear R, neutral gear N, and drive gear D can fully meet the needs of general driving. However, in some special driving environments, other functional gears may be required. Therefore, if the correct control method is chosen, an automatic transmission car can perform better than a manual transmission car. When waiting at a red light, whether to use N gear or D gear depends on personal preference. Temporarily stopping and holding the brake in D gear will not harm the car, because the torque converter in the transmission is equipped with a reaction wheel with a one-way clutch, which amplifies the torque from the engine crankshaft.
6
5
Share

Is It Normal for a New Car Engine to Have Sludge?

It is normal for a new car engine to have sludge. Reasons for sludge in the engine: When the car frequently operates at low speeds, the crankcase temperature remains low. Additionally, the fuel injection volume is higher during low-speed engine operation, causing some incompletely burned gasoline to enter the crankcase, resulting in low-temperature sludge. When the crankcase ventilation valve is partially or completely blocked by oil impurities or sludge, waste and water vapor inside the crankcase cannot be discharged in time, leading to sludge formation. To improve fuel economy, some high-performance direct-injection engines on the market use a technology called lean combustion, which reduces fuel injection. In China, due to poor fuel quality and lean combustion, exhaust gases entering the crankcase contain higher nitrogen oxide levels, contributing to sludge formation. Additionally, low-quality engine oil and gasoline can also cause sludge. Introduction to sludge: Sludge is a deposit formed in the engine during operation when impurities in the crankcase combine with thickened engine oil under high temperatures. It adheres to components such as the engine camshaft, crankcase, oil passages, and oil pan. Both sludge and carbon deposits are harmful substances that negatively impact engine performance.
6
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.