How to Start with One Button?

What Causes the Squeaking Noise When Braking and Releasing in BMW 3 Series?

BMW 3 Series squeaking noise when braking and releasing is generally caused by brake pad issues. Below are some explanations regarding the squeaking noise when braking and releasing in BMW 3 Series: Causes: For new cars, the brake discs and pads are brand new, so they need to be worn in. During this period, the brakes may produce abnormal noises, which can be categorized as vibration friction or sharp hissing sounds. These noises typically disappear after a few hundred kilometers. During sandstorms or in dusty conditions: Sand or dust particles may get between the discs and pads, causing a hissing noise when braking. Solutions: If the noise persists for a week or half a month and becomes increasingly louder, it indicates a fault with the brake pads. Otherwise, the cause may be something else, and the brake pads should not be mistakenly replaced. If a clunking noise occurs during sudden braking accompanied by vibration in the brake pedal, this situation can generally be ignored.

9

5

Share

What Happens If a Plastic Bag Blocks the Exhaust Pipe?

The consequences of a plastic bag blocking the exhaust pipe are as follows: 1. Insufficient Power: Intake, compression, power, and exhaust are the four strokes of an engine's working cycle. The exhaust pipe's task is naturally to expel exhaust gases, and for the exhaust to be smoothly discharged, it must pass through the exhaust manifold at the engine section, the catalytic converter in the middle section, and finally exit through the tailpipe. In principle, inserting a plastic bag will affect the exhaust process, which in turn will inevitably impact the intake phase. When the intake phase is affected, it leads to insufficient power. To maintain power, the vehicle will automatically increase fuel injection, but the extra fuel injected cannot be completely burned due to insufficient air intake, thus entering a vicious cycle. 2. Abnormal Vehicle Operation: The exhaust temperature is very high. If the exhaust is blocked, the high temperature can damage the piping, leading to other malfunctions. Therefore, when a plastic bag blocks the exhaust pipe, although it won't cause an explosion, it can easily result in abnormal vehicle operation. If the blockage is severe, it can directly prevent the engine from starting or cause it to stall, which can have serious consequences.

5

3

Share

What happens if the vehicle inspection validity period expires?

Driving a vehicle with an expired inspection validity period will result in 3 penalty points and a fine. If a traffic accident occurs involving a vehicle that has not undergone annual inspection, the party involved will bear full or primary responsibility. Driving without timely annual inspection is considered illegal operation and may lead to vehicle impoundment. If a vehicle fails to obtain the mandatory inspection compliance mark for three consecutive inspection cycles after the expiration of the inspection validity period, it will be subject to compulsory scrapping. Here is additional information: 1. Vehicle annual inspection: Vehicle annual inspection (or motor vehicle inspection) refers to the annual inspection conducted in accordance with the "Technical Conditions for Motor Vehicle Operation Safety" for vehicles that have already obtained official license plates and registration certificates. The purpose is to examine the main technical conditions of the vehicle, encourage enhanced vehicle maintenance, ensure the vehicle remains in good condition, and guarantee driving safety. 2. Annual inspection documents: Required documents include the vehicle registration certificate, compulsory traffic accident liability insurance policy (copy), the inspector's ID card, a triangular warning sign, and a fire extinguisher. (Vehicle violations must be resolved, and no modifications are allowed on the vehicle body).

9

1

Share

What is the H7/h6 fit clearance?

H7/h6 is a basic hole system fit clearance. H7/h6 is the tolerance fit code for mechanical components in the industry. H7 refers to the tolerance zone code of the hole to be matched, while h6 represents the tolerance zone code of the outer surface of the bearing (if the bearing is matched with the hole, then the bearing acts as the shaft). Below is more information about the clearance: 1. Function: The clearance serves to store lubricating oil, compensate for various errors, etc. Its size affects the relative motion between the hole and the shaft. 2. Main application: Clearance fits are primarily used for movable connections between holes and shafts, such as the connection between sliding bearings and shafts. The fit tolerance refers to the sum of the tolerance zones of the shaft and hole that form the fit, representing the allowable variation in clearance or interference. Its magnitude indicates the range of variation in the tightness of the fit and is an important comprehensive indicator for evaluating the quality of the fit.

12

2

Share

What are the precautions for new drivers who are afraid to drive after getting their license?

Here are the precautions for new drivers who are afraid to drive after getting their license: 1. Pay attention to speed: As long as it's not on the highway, new drivers should maintain a stable speed of around 60, which helps with control. 2. Observe the rearview mirrors more: The rearview mirrors allow you to see the road conditions behind and to the sides of the vehicle, especially when changing lanes, reversing, or overtaking, where they play a crucial role. 3. Maintain a safe distance: New drivers tend to follow too closely. If the car in front brakes or cuts in, new drivers often react by braking immediately, and sometimes excessive nervousness can cause the steering wheel to turn too sharply, leading to accidents. Therefore, keeping a safe distance from the car in front is key. When someone cuts in, slow down appropriately to yield. 4. Use lights correctly: Do not turn on the hazard lights randomly. Turn on the side marker lights in the evening, and fog lights should only be used in poor visibility conditions during foggy weather.

16

5

Share

How long does it take to change from C1 to C2?

C1 to C2 conversion typically takes about a week, and an appointment is required in advance. The difference between C1 and C2 is that C1 allows driving both manual and automatic transmission vehicles, while C2 only permits driving automatic transmission vehicles. Therefore, after the downgrade, the range of vehicles available for driving is significantly reduced. Additional information: 1. Method for changing from C1 to C2: Changing from C1 to C2 is considered a downgrade of the driver's license. The process requires visiting the traffic management office to fill out a downgrade confirmation form and signing it. Before taking the subject one exam, you can negotiate with the driving school to change the relevant procedures and pay the associated fees to switch to applying for a C2 driver's license. 2. Permitted vehicle types: (1) C1 permitted vehicle types: small and micro passenger cars, as well as light and micro trucks; light and micro special operation vehicles; and also permits driving vehicles under C2, C3, and C4 categories. (2) C2 permitted vehicle types: small and micro automatic transmission passenger cars and light and micro automatic transmission trucks.

14

2

Share

How to Start with One Button?

What Causes the Squeaking Noise When Braking and Releasing in BMW 3 Series?

What Happens If a Plastic Bag Blocks the Exhaust Pipe?

What happens if the vehicle inspection validity period expires?

What is the H7/h6 fit clearance?

What are the precautions for new drivers who are afraid to drive after getting their license?

How long does it take to change from C1 to C2?

What is the typical speed of a sedan?

Do new cars need to display annual inspection and compulsory insurance stickers?

What to Do When the Fuel Tank Cap of Golf 7 Won't Open?

What are the steps for removing and installing the air conditioning filter in a Golf?