How to start the Civic with one key?

1 Answers
DelMatteo
07/30/25 4:29am
The method to start the Civic with one key: Step on the foot brake, make sure the gear is in the P position, and then press the one-key start button to start. The one-key start of the car is part of the smart car device, which is a button device to achieve a simple ignition process, and it can also turn off the engine. The one-key start of the car can be modified at the position of the original car key lock, or it can be modified independently on the panel. The Civic is a model under Dongfeng Honda, with a body size of 4649mm in length, 1800mm in width, and 1416mm in height, and a wheelbase of 2700mm. The Civic has a grand and fashionable appearance, with smooth body lines, and the hatchback appearance has been greatly changed compared with the old model. The interior workmanship of the Civic is relatively fine, the design is also relatively fashionable, the sense of hierarchy is relatively prominent, and the functional configuration is relatively rich, but the large area of hard plastic leads to poor hand feeling, and the seat comfort is good.
Was this review help?
5
1
Share
More Forum Discussions

Is the Parking Brake System the Handbrake?

Parking brake system is the handbrake. More information about the parking brake system is as follows: 1. Parking brake, commonly known as handbrake. Function: Provides resistance to the car when parked. 2. The parking brake is either the handbrake or the parking gear in an automatic transmission, used to lock the drive shaft or rear wheels. The parking brake has less force than the service brake and only prevents the vehicle from rolling when parked on a slope. 3. There are different types of parking brakes. Mechanical mechanisms operated by hand or foot; high-end vehicles increasingly use electronically controlled parking systems, commonly known as electronic handbrakes. 4. Traditional handbrakes require the driver to manually release the handbrake or skillfully coordinate the throttle and clutch for a smooth start on a slope; electronic handbrakes use a slope sensor to provide accurate parking force through the controller.
13
1
Share

How to Use the Cruise Control on the Roewe i6?

Roewe i6 cruise control method is as follows: 1. To use the cruise control system, first pull the lever inward to activate the system. 2. Store the current speed by pressing the set button. 3. Move the lever upward to increase speed; downward to decrease speed; maintain unchanged for rapid speed increase or decrease. 4. Press the accelerator or push the lever downward to temporarily cancel the function; release the accelerator or push the lever inward to automatically resume the function; push the lever to the end or apply the brake to cancel the function, and the indicator light will turn off.
20
0
Share

What are the reasons why a car door won't close?

The reasons why a car door won't close: the hinge or latch of the door is displaced, the door lock tongue cannot reverse and latch properly, issues with the door lock contact switch, or insufficient height of the contact installation. Solutions are as follows: 1. Open the door and use a T-20 spline to loosen the screw in the small hole on the door edge. 2. Remove the small cover of the door handle. 3. Loosen the cable in the door handle slot slightly. 4. If the above methods still cannot resolve the issue, promptly send the car to a 4S shop for replacement or repair. Functions of car doors: provide access for the driver and passengers, isolate external interference, and to some extent, mitigate side impacts.
20
0
Share

What Causes the Wiper Blade to Make Noise When Wiping the Windshield?

The reasons for the wiper blade making noise when wiping the windshield are as follows: 1. The wiper blade has aged. Solution: Replace the wiper blade with a new one. Generally, it is recommended to replace wiper blades every one to two years. 2. There is debris stuck in the wiper blade. Solution: Inspect and clean the wiper blade or remove any debris underneath it. 3. Incorrect installation angle of the wiper arm. Solution: Place a cloth under the head of the wiper arm to ensure the wiper blade is perpendicular to the windshield. 4. Abnormal movement caused by deformation, jamming, or rust in the linkage mechanism. Solution: It is recommended to clean the windshield with a cleaning solution or replace the wiper blade with a new one.
4
3
Share

What Causes Steering Wheel Vibration?

Steering wheel vibration causes and solutions are as follows: 1. Idle vibration: Loose steering wheel bolts or rubber bushings. The idle vibration issue is relatively minor and can be resolved by yourself. Solution: Tighten the bolts or rubber bushings. 2. Vibration during driving: When wheel balance is abnormal, the tires become unbalanced and bounce during driving. Since the steering wheel is connected to the tires, the force is transmitted through the drive shaft to the steering wheel, causing vibration which signals abnormal wheel balance. Solution: Requires inspection and repair at a 4S shop or repair facility.
18
2
Share

What to Do When the Car Transmission Fails?

Car transmission damage should be replaced. The correct usage methods of the transmission are as follows: 1. Avoid coasting in N gear: Manual transmissions can coast in neutral, but automatic transmissions cannot. The principle of automatic transmission is different from manual transmission; coasting in N gear can easily burn out the transmission. 2. Do not shift to P gear while waiting at traffic lights: Shifting to P gear (Park) when waiting at traffic lights, if rear-ended, will cause transmission damage. When parking, first apply the foot brake, wait until the car is completely stopped, then shift to P gear to avoid P gear jamming. 3. Shifting gears too quickly: When the car is not completely stopped, shifting from D gear to R gear creates an instantaneous reverse pressure that pushes against the reverse gear clutch plate, causing excessive wear on the clutch plate.
17
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.