How to Start a Geely Vehicle When the Key Fob Battery Dies?

1 Answers
MacEmersyn
07/29/25 9:47pm
Geely Vehicle Key Fob Battery Dies Starting Method: Use the mechanical key to open the door, press the brake pedal, place the remote key near the induction area or close to the start button. Once the start button indicator turns green, remove the smart key to start the vehicle. Car key batteries are typically button cells with a long lifespan, usually lasting over 3 years. The Geely Icon is a compact SUV under the Geely brand, with body dimensions of 4350mm in length, 1810mm in width, and 1615mm in height, and a wheelbase of 2640mm. The entire Geely Icon lineup is equipped with a 1.5-liter turbocharged engine, capable of delivering 177 horsepower and a maximum torque of 255 Nm.
Was this review help?
19
2
Share
More Forum Discussions

Why does the car intermittently shake when in N gear?

The reasons for intermittent shaking when the car is in N gear: When in N gear, power is not transmitted to the drive wheels, which experience a temporary reverse force. However, power is still delivered to the winch, preventing it from reversing. These opposing forces cause the car to shake when both act simultaneously. Below are some related additional details: 1. If the shaking is less noticeable when braking compared to shifting without braking, it indirectly indicates that the transmission and engine are not well matched. 2. Generally, achieving smooth shifting from N to D requires extensive tuning for each car model. However, due to cost constraints, many vehicles' N to D shifting performance is unsatisfactory.
3
0
Share

Where is the fuse box of the Santana?

The fuse box of the Volkswagen Santana is located on the left side of the dashboard, inside the cover above the driver's footwell, near the clutch pedal. The function of the car fuse box: When a circuit malfunctions or behaves abnormally, the current may continuously rise, potentially damaging important or expensive components in the circuit, or even causing a fire. If a fuse is correctly installed in the circuit, it will melt and cut off the current when the current rises abnormally to a certain level and duration, thereby protecting the circuit's safe operation. A relay is essentially an "automatic switch" that uses a smaller current to control a larger one. Thus, it plays roles in automatic regulation, safety protection, and circuit switching within the circuit. Symptoms of a blown car fuse: If the battery has power but the vehicle won't start, this symptom is likely due to a blown fuse responsible for the starter motor. It's important to note that when the vehicle fails to start, avoid continuous attempts to start the engine, as this can drain the battery completely. While driving, if the tachometer shows normal readings but the speedometer displays zero and the ABS warning light is on, this indicates that the fuse corresponding to the ABS has blown. Some unscrupulous dealers may remove the ABS fuse during vehicle transport to prevent the odometer from increasing, but this poses significant risks. A vehicle without ABS can be very dangerous in emergency situations. If pressing the windshield washer switch does not spray washer fluid, it may be due to a blocked nozzle or freezing in cold weather. Avoid continuously pressing the switch, as prolonged use can overheat the motor and blow the corresponding fuse.
10
5
Share

What are the reasons for abnormal noises after replacing brake discs and pads?

The reasons for abnormal noises from newly replaced brake pads are as follows: 1. The most likely cause is an improper contact surface, where the old brake disc was not resurfaced when installing new brake pads, resulting in a poor fit. If the installation is improper or new pads are installed without resurfacing the old disc, the new pads will directly rub against the uneven surface of the old disc, ultimately causing uneven wear on the new brake pads. 2. Another possible reason is a defect in the brake system itself, causing the brake pads to only partially contact the brake disc. This increases the pressure per unit area during braking, leading to abnormal noises. It is recommended to inspect components such as the caliper and guide pins.
5
0
Share

Can a B1 Driver's License Be Upgraded to an A2?

Currently holding a B1 driver's license, you can directly upgrade to an A2, but you must have held the B1 license for more than three years or have held a large passenger vehicle driving qualification for more than one year. Additionally, you must not have accumulated 12 penalty points in any of the last three scoring cycles before applying. To upgrade from a B1 to an A2 driver's license, the following conditions must be met: 1. You must already hold a motor vehicle driver's license, and when applying to add a new vehicle class, you must not have accumulated 12 penalty points in the current scoring cycle or the most recent scoring cycle before applying. 2. You must have held a medium or large passenger vehicle driving qualification for more than three years or a large passenger vehicle driving qualification for more than one year, and you must not have accumulated 12 penalty points in any of the last three consecutive scoring cycles before applying.
7
1
Share

What Causes Water Leakage from a Car's Exhaust Pipe?

Exhaust pipes drip water because gasoline contains trace amounts of moisture, which cannot be burned. During combustion in the engine's combustion chamber, these trace amounts of moisture are separated from the gasoline. This moisture is then expelled with the exhaust gases. Inside the cylinder, the temperature is quite high, but as the moisture enters the exhaust pipe, it rapidly cools and condenses, forming water vapor that adheres to the inner walls of the exhaust pipe. As more water vapor accumulates, it eventually forms droplets that flow out of the exhaust pipe. Thus, water dripping from the exhaust pipe does not indicate a car malfunction. In fact, it can even suggest that the engine is of good quality, as the formation of water droplets indicates that the fuel is being burned efficiently.
18
3
Share

What are the tire specifications for the Focus?

The tire specifications for the Focus are as follows: 1.6L model - 205/60-R16; 2.0L model - 215/50-R17. Below is relevant information about tires: 1. The international standard tire code represents the section height and aspect ratio as a percentage in millimeters, followed by the tire type code, rim diameter (in inches), load index (permissible load capacity code), and permissible speed code. 2. Tires are one of the crucial components of a vehicle, directly contacting the road surface and working with the suspension system to absorb shocks during driving. They ensure good ride comfort and smooth operation, maintain excellent traction between wheels and road surfaces, improve vehicle traction, braking, and off-road capability, and bear the vehicle's weight.
19
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.