How to Start a Boyue Car?

Which gear should be used for oncoming traffic in Subject 3?

For oncoming traffic in Subject 3, either 2nd or 3rd gear can be used, depending on the vehicle speed. Precautions for oncoming traffic and gear shifting methods are as follows: Precautions for oncoming traffic: Pay attention to traffic signals and signs during oncoming traffic; in situations with unclear visibility, reduce speed in advance and drive with low beams; avoid using emergency braking, suddenly releasing the accelerator, or jerking the steering wheel during oncoming traffic; avoid oncoming traffic near obstacles; avoid oncoming traffic in narrow bridges, narrow roads, tunnels, sharp turns, and other complex locations; avoid not turning off high beams during nighttime oncoming traffic. Gear shifting in Subject 3: Start in 1st gear; the gear shifting sequence is 1-2-3-4-2; use 1st gear for U-turns; stop and wait at traffic lights in 1st gear; normally drive in 2nd gear; maintain 2nd gear for straight-line driving; use 2nd gear for both overtaking and lane changes; shift to 1st gear to slow down and stop before pulling over.

10

0

Share

Does canceling the appointment three times for Subject 3 affect the test?

Subject 3 canceling the appointment three times does not affect the test. The relevant content about canceling Subject 3 is as follows: Methods to cancel Subject 3: To cancel the test appointment at the vehicle management office, you need to bring your original ID card and a copy, and write on the blank space of the ID card copy that you voluntarily cancel the Subject test at the driving school on a certain date, and sign your name, contact information, and date in the blank space. In addition to canceling at the vehicle management office, you can also cancel the driving test appointment on your mobile phone or the internet. If you have only successfully submitted the appointment application, you can cancel the appointment on the traffic management website by following the prompts. If you have already received a text message from the vehicle management office notifying the successful appointment date, you can only cancel the appointment at the vehicle management office, and you must go there at least one day in advance. Limitations on canceling the test: The driving test center information platform only allows cancellation of Subject 3 appointments, and the latest time to cancel is before 12 noon the day before the scheduled test date. For Subject 1, Subject 2, and the safety civilization test, students must cancel on the official appointment website of the driving test center or contact their driving school to cancel.

11

3

Share

What is the passing score for Subject 3?

Subject 3 requires a passing score of 90 points. Below are the key points to note for the Subject 3 test: Preparation before starting: Candidates must follow the safety officer's instructions to approach the vehicle, walk around it (from the left front door to the rear), and confirm safety before opening the door to enter. After entering, upon hearing the voice prompt "Please prepare for the test and perform fingerprint verification," first adjust the seat to a comfortable position, adjust the interior and exterior rearview mirrors, and fasten the seat belt. Then proceed with fingerprint verification. The fingerprint scanner is located below the left air vent on the steering wheel. Night driving: After successful fingerprint verification, daytime test candidates will hear the voice prompt "Now begins the simulation of nighttime light usage, please follow the voice prompts to operate" before starting. Candidates should then begin the light operation. The nighttime light simulation test will randomly select three items from the following for examination.

12

1

Share

Why can't the tricycle shift gears?

For clutches equipped with pneumatic or hydraulic boosters, if the clutch pedal feels heavy, it indicates poor performance of the booster system. Possible causes include air leaks in the pipeline system, wear of the cylinder piston seals, or poor sealing of the exhaust valve, which weaken the booster effect. The details are as follows: Reason 1: Slippage in hydraulically operated clutches is often due to insufficient free travel of the clutch pedal, causing the release bearing to press against the release lever or diaphragm and rotate with it. Adjust the return position of the clutch pedal and the length of the master cylinder push rod. Reason 2: Loose fit of the gear lever limit pin. Synchronizer damage or failure, excessive damping spring force, or prolonged vehicle inactivity can lead to severe rusting of the shift block, shift linkage, shift pin shaft, transmission differential, shift pin, and pivot bolt due to lack of lubrication.

17

5

Share

How many hours are required for Subject 2 check-in?

Subject 2 requires a daily check-in of 2 hours. The total check-in duration and related details for Subject 2 are as follows: Total check-in duration for Subject 2: You must complete 16 hours of study for Subject 2 before you can schedule the exam. However, daily practice check-in time cannot exceed 2 hours, so the study period will be five and a half days. After completing the required hours, you can schedule the exam. Therefore, the fastest possible time is seven days. Relevant regulations: Each study hour lasts 60 minutes, with effective teaching time being no less than 45 minutes. Daily theory and in-car practice cannot exceed 4 hours each. According to requirements, each subject must complete the stipulated study hours, be reviewed and approved by the road transport management department, and then transmitted to the public security traffic management internet service platform before the student can schedule the exam. Subject 2 test items: The C1/C2 driving test items include five mandatory components: reverse parking, parallel parking, stopping and starting on a slope, right-angle turns, and curve driving.

2

4

Share

Can You Stop During Straight-Line Driving in Subject 3?

You cannot stop during straight-line driving in Subject 3. The reasons and exam content are as follows: No stopping during straight-line driving: Naturally, you cannot stop during straight-line driving. Once the system announces the start of straight-line driving, stopping will result in failure. Therefore, before starting straight-line driving, ensure there are no obstacles ahead and maintain a distance of at least 100 meters from the vehicle in front. Only after the system announces the end of straight-line driving can you stop and perform other actions. Subject 3 exam content: The road driving skills test for Subject 3 generally includes: vehicle preparation, light simulation test, starting, straight-line driving, gear shifting operations, lane changing, pulling over, going straight through intersections, left turns at intersections, right turns at intersections, crossing pedestrian crossings, passing school zones, passing bus stops, meeting vehicles, overtaking, U-turns, and night driving. The safety and civilized driving knowledge test generally includes: safety and civilized driving operation requirements, safe driving knowledge in adverse weather and complex road conditions, emergency handling methods for situations like tire blowouts, and post-accident handling knowledge.

11

5

Share

How to Start a Boyue Car?

Which gear should be used for oncoming traffic in Subject 3?

Does canceling the appointment three times for Subject 3 affect the test?

What is the passing score for Subject 3?

Why can't the tricycle shift gears?

How many hours are required for Subject 2 check-in?

Can You Stop During Straight-Line Driving in Subject 3?

Does Not Signing After Passing Subject 1 Affect the Test Result?

Should I Watch the Subject One Videos Carefully?

How long does it take to review the reservation for Subject 3?

Must the second retake of Subject 1 be conducted on the same day?