···
Log in / Register

How to Spray Water with the Windshield Wiper?

4 Answers
OIsaac
07/29/25 9:56pm

Method for spraying water with the windshield wiper: Pull the wiper control lever (the lever on the right side of the steering wheel) toward the driver to spray water. Introduction to the windshield wiper: 1. The car windshield wiper should be replaced every 1 to 2 years. It is an important component of the car and plays a crucial role during rainy season driving. The windshield wiper is a device used to remove raindrops and dust attached to the vehicle's windshield, improving the driver's visibility and enhancing driving safety. 2. The car windshield wiper is a consumable item. After prolonged use, it is inevitable that it will age, so it needs to be checked and replaced regularly.

Was this review help?
8
5
Share
VonLane
08/15/25 9:43pm

Having driven for over 20 years, I can say that using windshield washer fluid is simple but requires proper technique. Pull the wiper control stalk beside the steering wheel—usually a gentle backward or forward tug—and you'll see fluid spray onto the windshield as the wipers activate. This operation cleans the windshield, improving visibility, which is especially crucial during rain, snow, or dusty conditions. Always check if there's fluid in the reservoir; no fluid means no spray. I recommend checking the reservoir level weekly and topping it up with dedicated cleaning solution to prevent freezing in winter. Avoid operating on a dry windshield to prevent surface scratches. Safety tip: After spraying, ensure the wipers clear the windshield properly—otherwise, replace the blades or have a mechanic adjust the nozzle angle. Developing good driving habits, even these small actions, can be lifesavers in critical moments.

Was this review help?
14
2
Share
Expand All
GenesisLynn
10/17/25 6:44am

As a new driver, I didn't quite understand the windshield washer operation when I first started. Basically, you just pull the wiper stalk on the right side of the steering wheel - one pull releases the washer fluid while the wipers clean the windshield. Remember to pull gently, not forcefully, otherwise the water might splash everywhere which can be quite embarrassing. I was so nervous during my first attempt that I pulled the wrong direction, but after practicing a few times I got the hang of it. The key is to check if the washer fluid reservoir is filled; if it's empty, the washer won't work properly and you might damage the pump. Just use it when visibility gets blurry during normal driving - don't overuse it and waste resources. These basic skills are quick to learn, but safe driving relies on mastering such details. New drivers should practice more and it'll become second nature.

Was this review help?
10
1
Share
Expand All
OHope
11/30/25 7:26am

I start teaching my child about driving with the windshield washer function. It's simple to operate: just pull the wiper control lever to spray water. The key point is regular maintenance – check the washer fluid reservoir level and top it up in time, don't wait until it's urgently needed and can't spray, which may affect driving safety. This feature is most practical during rainy days or when the windshield gets dirty at night, as it can reduce potential traffic hazards. Develop a habit of cleaning while driving daily, and don't overlook small things.

Was this review help?
8
3
Share
Expand All
More Forum Discussions

Which is Better, Direct Injection or Multi-Point Fuel Injection for Cars?

Multi-point fuel injection is generally better for cars. The differences between direct injection and multi-point fuel injection are as follows: Fuel Consumption: Direct injection has lower fuel consumption, while multi-point fuel injection has lower requirements for fuel quality. Components: Both direct injection and multi-point fuel injection have complex structures and higher costs. Operation: In a direct injection engine, high-pressure fuel is injected into the combustion chamber in a fine mist, which absorbs heat as it evaporates, cooling the cylinder and thereby reducing emissions. Multi-point fuel injection involves injectors installed on the intake pipe of each cylinder, with fuel being injected into the cylinder from multiple points. Technical Requirements: Direct injection has higher technical requirements, with the main challenge being the implementation of stratified combustion. Multi-point fuel injection improves upon the uneven distribution of the air-fuel mixture seen in single-point injection but does not enhance fuel atomization or the mixing of fuel and air.
19
3
Share

What is the normal voltage for a car fuel pump?

Car normal fuel pump voltage is 350 volts. The following is an introduction to the fuel pump: Fuel pump composition: Among the four wires of the car fuel pump, two are fuel level sensors (commonly known as floats), one is for power supply, and one goes to the fuel gauge; the other two are fuel pump wires, one for power supply and one for grounding. The fuel pump has a large working current, so the wires are thicker, while the sensor wires are thinner, making them easy to distinguish. Function of the fuel pump: It is to draw gasoline from the fuel tank and deliver it through pipes and the fuel filter to the float chamber of the carburetor. Thanks to the fuel pump, the fuel tank can be placed at the rear of the car, away from the engine and lower than the engine. There is no fixed replacement cycle for the fuel pump. Generally, after about 100,000 kilometers of driving, the fuel pump may show abnormalities.
16
3
Share

What does torque refer to in car parameters?

Torque in car parameters refers to the torque force of the vehicle and the moment output from the crankshaft end of the engine. Here are specific details about torque: 1. With a fixed engine power, torque is inversely proportional to the engine speed. The faster the speed, the smaller the engine torque; the slower the speed, the greater the engine torque. This also reflects the vehicle's load capacity within a certain range. 2. Like power, torque is one of the indices of a car engine, reflecting the vehicle's performance, including acceleration, climbing ability, and suspension. 3. The definition of torque is: the reciprocating motion of the piston in the cylinder, where each reciprocation does a certain amount of work, measured in Newton.
18
2
Share

What is the fuel consumption of the Everest?

The Everest currently has 11 models on sale. Among them, the Everest 2020 2.3T gasoline automatic two-wheel drive luxury edition 5-seater and elite edition 5-seater, equipped with a 275 horsepower engine, have an NEDC fuel consumption of 9.3L per 100 km. The Everest 2020 2.3T gasoline automatic four-wheel drive luxury edition 7-seater, flagship edition 5-seater, flagship edition 7-seater, luxury edition 5-seater, and elite edition 5-seater; as well as the sports edition 2.3T gasoline automatic four-wheel drive luxury edition 5-seater, flagship edition 7-seater, luxury edition 7-seater, and flagship edition 5-seater, totaling 9 models, all equipped with a 275 horsepower engine, have an NEDC fuel consumption of 10.1L per 100 km. The fuel tank capacity is the same across different Everest models. The distance that can be covered on a full tank of fuel is as follows: For models equipped with a 275 horsepower engine, the fuel tank capacity is 80L, and the distance that can be covered on a full tank is 80/9.3 100=860 km. For models equipped with a 275 horsepower engine, the fuel tank capacity is 80L, and the distance that can be covered on a full tank is 80/10.1 100=792 km. Vehicle fuel consumption is directly influenced by five major factors: driving habits, the vehicle itself, road conditions, natural wind, and environmental temperature. Specific factors that can increase fuel consumption include: Driving habits: Aggressive driving behaviors such as sudden acceleration, frequent overtaking, and not easing off the throttle before stopping at a red light can increase fuel consumption. The vehicle itself: Vehicles with larger engine displacements generally consume more fuel than those with smaller displacements because larger displacements typically produce more power and require more gasoline to burn and perform work. Heavier vehicles also consume more fuel due to the greater driving torque needed to move the additional weight. Road conditions: Driving on unpaved roads, muddy roads, soft surfaces, or mountainous terrain increases resistance and fuel consumption. Natural wind: Driving against the wind or on windy days increases vehicle resistance and fuel consumption. Low environmental temperatures: When the engine block is cold, the injected gasoline does not atomize easily, requiring more gasoline to be injected for combustion, which increases fuel consumption. Additionally, in cold temperatures, the engine's computer may control the engine to run at higher RPMs to warm up, further increasing fuel consumption.
6
0
Share

Can the clutch height of the classic Nissan Sylphy manual transmission be adjusted?

The clutch height of the classic Sylphy manual transmission can be adjusted. There is a small clutch lever near the transmission under the car, where the lever connects to the clutch cable. A screw at this connection allows for height adjustment. After adjustment, start the car to test the clutch. There is no way to adjust the clutch weight of the new Nissan Sylphy. If the clutch becomes increasingly heavy to press, the main causes may be issues with the clutch pressure plate, clutch disc, or release bearing. In such cases, it is necessary to visit a 4S shop for repairs. Relevant precautions for the clutch: The clutch must be thoroughly cleaned before installation to remove anti-rust grease and debris. The clutch can be installed coaxially or on separate shafts. The axial direction must be fixed, and neither the driving nor the driven parts should have axial movement. When installed on separate shafts, the coaxiality between the driving and driven shafts should not exceed 0.1mm.
17
1
Share

How Often Should You Change Transmission Fluid?

It is recommended to change the transmission fluid every two years or 40,000 kilometers, whichever comes first. Transmission fluid is an oil product that keeps the car's gear system clean. Below are the advantages of transmission fluid: 1. Transmission fluid ensures smooth and seamless gear shifting, improving driving performance. 2. It provides excellent oxidation resistance, reducing rust on mechanical parts. 3. Transmission fluid contains high-quality extreme pressure additives, offering optimal protection for gear assemblies. 4. Using transmission fluid provides the best anti-wear effect for the car's transmission, extending the lifespan of the automatic transmission.
16
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.