How to Solve the Throttle Lag Issue in MG6?

1 Answers
OMalachi
07/29/25 5:27pm
The solutions for throttle lag in MG6: 1. The slow throttle response might be related to the gasoline you usually use. It's best to stick to a fixed gasoline grade, such as consistently using 95-octane fuel, and avoid frequent changes; 2. If the throttle response is slow, check if the air filter, intake valve, intake pipe, and various vacuum hoses are clogged or damaged. Address any issues promptly to prevent more severe car problems; 3. Slow throttle response could also be due to power transmission issues. A test drive is needed to check if there's transmission slippage or gear jamming; 4. The slow throttle response might be caused by a faulty throttle pedal sensor. Seek professional help for repairs; 5. Slow throttle response could also result from clogged or leaking fuel injectors. Inspect the fuel injectors promptly; 6. Another possible cause of slow throttle response is related to driving habits. When accelerating normally, avoid pressing the throttle too quickly or too slowly—maintain a balanced approach. In terms of dimensions, the MG6 measures 4704mm in length, 1848mm in width, and 1466mm in height, with a wheelbase of 2715mm.
Was this review help?
1
0
Share
More Forum Discussions

How to remove the BYD F3 heater switch?

Method to remove the BYD F3 heater switch: Take off the middle knob, remove the screws, then pry open the center console panel to take out the heater switch. Here is how to turn on the BYD F3 heater: Switch location: The three knobs above the center storage box on the dashboard. Method: After starting the car, wait for 5-10 minutes until the BYD F3's water temperature reaches normal operating temperature. At this point, you can turn on the BYD F3 heater. Adjust the air conditioning circulation mode to internal circulation, then turn the third knob to the red zone. Do not turn on the middle knob; rotate the first knob to adjust the appropriate fan speed and air vent direction.
16
3
Share

Can the Jetta VS5 use 92 octane gasoline?

According to the compression ratio of the Jetta VS5 engine, the Jetta VS5 can use 92 octane gasoline. Generally, the fuel tank cap of the car will indicate that 95/92/97/93 octane gasoline can be used. It is recommended to use the manufacturer-recommended 95 octane gasoline, but 92 octane gasoline can also be used. However, in terms of anti-knock performance, the higher the octane number, the better. Gasoline usage recommendations: 95 octane gasoline consists of 95% isooctane and 3% n-heptane. High-compression engines should use high-octane gasoline. If a high-compression engine uses low-octane gasoline, it may cause abnormal combustion, resulting in knocking, increased fuel consumption, and reduced power, making it suitable for high-end cars. 92 octane gasoline has an octane rating of 92 and consists of 8% n-heptane, making it suitable for mid-range cars. Gasoline grades are classified by octane number, and the anti-knock performance of automotive gasoline is indicated by the octane number. The higher the octane number, the better the anti-knock performance. The anti-knock capability of gasoline is related to its chemical composition. Branched-chain alkanes, olefins, and aromatic hydrocarbons generally have excellent anti-knock properties. Isooctane is assigned an octane number of 100, indicating good anti-knock performance, while n-heptane has an octane number of 0, indicating poor anti-knock performance. The octane number of gasoline is measured by an octane rating engine. High-octane gasoline can meet the needs of high-compression gasoline engines. The higher the compression ratio of a gasoline engine, the higher the thermal efficiency, which can save fuel.
8
0
Share

Where to Buy Car Windshield Washer Fluid?

Car windshield washer fluid is available at supermarkets, gas stations, 4S stores, car beauty shops, or auto parts markets. Below is some relevant information about windshield washer fluid: Activity of Windshield Washer Fluid: When purchasing car windshield washer fluid, shake the bottle to see if there are plenty of bubbles in the fluid. More foam indicates a higher amount of active agents in the fluid, and the foam should be fine and dense. Viscosity of Windshield Washer Fluid: To determine the viscosity of the windshield washer fluid, turn the bottle upside down and observe how quickly the bubbles rise. Slower rising bubbles indicate higher viscosity. You can also dip your finger into the fluid; if it feels very thick, it indicates a high-quality windshield washer fluid.
11
3
Share

What does the rear axle ratio of a truck mean?

The rear axle ratio of a truck refers to the gear transmission ratio of the main reducer in the truck's drive axle, which is equal to the ratio of the rotational angular velocity of the drive shaft to the rotational angular velocity of the axle's half-shaft. Below is relevant information about the rear axle ratio: Key Factors: The rear axle ratio is related to the gears. The power output from the engine and transmission acts on the drive shaft, which rotates to input power to the pinion gear of the main reducer, driving the ring gear of the main reducer to rotate, and then driving the half-shaft to rotate. Calculation Formula: The number of teeth on the driven gear of the main reducer divided by the number of teeth on the driving gear of the main reducer. Simply put, if the drive shaft rotates N times to drive the half-shaft to rotate once, then N is the rear axle ratio.
9
2
Share

What model is the Lavida Classic?

Lavida Classic is a compact sedan under SAIC Volkswagen. The new Lavida is equipped with three types of engines: a 1.5L naturally aspirated engine, a 1.4L turbocharged engine, and a 1.2L turbocharged engine. The specific engines are as follows: 1.2L turbocharged engine: The 1.2L turbocharged engine delivers 116 horsepower and a maximum torque of 200 Nm. This engine can output maximum power at 5,000 rpm and maximum torque between 2,000 and 3,500 rpm. It features direct fuel injection technology and uses an aluminum alloy cylinder head and block. It is paired with a 7-speed dual-clutch transmission. 1.4L turbocharged engine: The 1.4L turbocharged engine delivers 150 horsepower and a maximum torque of 250 Nm. This engine can output maximum power at 5,000 rpm and maximum torque between 1,750 and 3,000 rpm. It features direct fuel injection technology and uses an aluminum alloy cylinder head and block. It is paired with a 7-speed dual-clutch transmission. 1.5L naturally aspirated engine: The 1.5L naturally aspirated engine delivers 113 horsepower and a maximum torque of 145 Nm. This engine can output maximum power at 6,000 rpm and maximum torque at 3,900 rpm. It features multi-point fuel injection technology and uses an aluminum alloy cylinder head and block.
6
1
Share

What does push mean in a car?

Push in a car indicates that the button's operation method is pressing. The functions and identification methods of push are as follows: Corresponding functions: Usually, push appears together with corresponding function icons or characters, indicating that this function can be activated by pressing. If a knob has the push character in the middle, it means the center of the knob can be pressed, and pressing the knob can activate a certain function. Identification methods: For the air direction (also called mode) knob, pushing the center (push) turns on the light and activates the rear window defrost. For the temperature (also called warm/cold) knob, pushing the center (push) turns on the light and activates the internal circulation.
16
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.