How to Solve the Resonance Noise from the Front Right Door?

2 Answers
DeJason
07/24/25 4:17am
Here are the solutions for resonance noise from the front right door: 1. The door hinges may have rusted or deformed due to prolonged use. Clean the surface dirt from the door hinges, limiter arm, limiter pin shaft, and connecting bracket, and then apply specialized lubricating oil appropriately. 2. The noise could be caused by loose or deformed internal window regulators. 3. It might also be due to unstable fixing of the door trim panel or detached fixing clips. Here is some related information about resonance noise: 1. Doors and the car body are connected via hinges. Noise from hinges after prolonged use is normal. To ensure the hinges remain smooth and quiet, apply lubricating oil every 2 to 3 months for maintenance. 2. In some cars with average assembly quality, the door limiters are prone to deformation, leading to noise. In such cases, professional repair or replacement at a service center is necessary.
Was this review help?
12
4
Share
Beatrice
08/10/25 11:54pm
I've driven many cars, and the most common cause of resonance noise in the right front door is loose interior panels or components, which accumulate noise from long-term vibrations. If the clips of the interior panel aren't fastened tightly, gently press to see where the movement is, then remove the panel to tighten the screws or add some cushioning material to fix it. Aging seals can also cause noise, especially noticeable at high speeds with a whooshing sound—check for cracks and replace if necessary. Loose door lock mechanisms or bolts in the window regulator bracket can also lead to noise; try adding some lubricant. Avoiding bumpy roads can help slow down the issue, but to solve it fundamentally, a thorough inspection is needed—start from the simple to the complex, identify the problem step by step, then proceed with repairs.
Was this review help?
16
4
Share
Expand All
More Forum Discussions

What engine is used in the Jianghuai M3?

Jianghuai M3 is equipped with a 1.8-liter naturally aspirated engine. The Jianghuai M3 is a compact MPV with body dimensions of 4715mm in length, 1765mm in width, 1900mm in height, a wheelbase of 2810mm, and a fuel tank capacity of 55 liters. The maximum power output of the Jianghuai M3 engine is 110 kW, with the maximum power achieved at 5500 rpm, and the maximum torque is 210 Nm. It is paired with a 5-speed manual transmission. The front suspension features a double-wishbone torsion bar independent suspension, while the rear suspension uses a leaf spring non-independent suspension. The tire specification is 205/65R15.
3
5
Share

How to Interpret Tire Specifications?

Tire specification parameters represent the tire's width, aspect ratio, tire type, and applicable size. Taking the 225/60R17 model as an example: 1. 225 indicates the tire section width is 225mm; 2. 60 is the aspect ratio, meaning the tire's sidewall height is 60% of the tire section width; 3. R stands for radial tire; 4. 17 indicates the tire is suitable for 17-inch rims. Radial tire: The tread part is reinforced with steel belts, allowing it to withstand higher internal pressure stress, featuring less tread deformation, better ground grip, and stability, making it more suitable for high-speed driving. Nowadays, radial tires are commonly used in passenger cars.
4
5
Share

Why does the reversing camera screen always flicker when reversing?

Generally, it's an issue with the reversing camera, which can be resolved at a 4S shop. Below is relevant information about reversing cameras: 1. Introduction to reversing cameras: A reversing camera, also known as a parking assist system, reverse visual system, or vehicle monitoring system (English name: vehicle-backup-camera), is widely used in various large, medium, and small vehicles for reversing or driving safety assistance. 2. Advantages of reversing cameras: Installation is simple. Typically, a standard single-output reversing camera only requires connecting the positive power wire to the positive terminal of the car's reversing light power and the negative power wire to the negative terminal of the reversing light or to ground (GND). Wiring can be easily understood by studying the vehicle model, and the camera can be installed by drilling a hole in an easily accessible location.
4
1
Share

What are the body dimensions of the Mercedes-Benz E300?

The body dimensions of the Mercedes-Benz E300 are: length 5078 mm, width 1860 mm, and height 1484 mm. The Mercedes-Benz E300 is a model produced by Beijing Benz, featuring a 4-door, 5-seater sedan body structure with a wheelbase of 3079 mm and a fuel tank capacity of 66 liters. The E300 is equipped with a 2.0T turbocharged engine, delivering a maximum power of 190 kW at 5800 to 6100 rpm and a peak torque of 370 Nm. It adopts a front-engine, rear-wheel-drive layout, with multi-link independent suspension systems for both the front and rear. The vehicle is paired with a 9-speed automatic transmission.
2
3
Share

How to Fix a Non-Responsive Rearview Camera?

Display unit freezing or slow response can be resolved by restarting the navigation system or the vehicle. Below is relevant information about rearview cameras: 1. Introduction to Rearview Cameras: Also known as parking assist systems, reverse camera systems, or onboard monitoring systems. English name: vehicle-backup-camera. This system is widely used in various large, medium, and small vehicles for reversing or driving safety assistance. 2. Advantages of Rearview Cameras: Simple installation. Generally, a standard single-output rearview camera only requires connecting the power wire's positive terminal to the vehicle's reverse light positive power source, and the negative terminal to the reverse light negative or ground (GND). Wiring can be easily understood by studying different vehicle models, and the camera can be installed by drilling holes in convenient locations.
1
0
Share

How to resolve abnormal tire pressure warning on Audi dashboard?

When the Audi dashboard displays an abnormal tire pressure warning, the resolution methods and parameters are as follows: 1. Resolution method: First, identify which tire has insufficient pressure. You can visit an auto repair shop or perform the check yourself. Use an air pump to inflate the underinflated tire, then recheck the tire pressure to ensure it has reached the proper level. Once the pressure is normal, the warning light will automatically turn off. 2. Parameter explanation: Audi's tire pressure monitoring system utilizes ABS sensors to compare the rolling circumference and vibration patterns of each wheel. A yellow tire pressure light indicates at least one tire has minor air leakage, while a red tire pressure light signals at least one tire has significant air leakage requiring immediate parking for inspection.
20
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.