How to Solve the Problem of High Fuel Consumption?

1 Answers
Duane
07/29/25 9:43pm
High fuel consumption can be addressed by inspecting and repairing car components. Here are specific methods to solve high fuel consumption: 1. Clean engine carbon deposits: Excessive carbon deposits in the engine are a major cause, primarily due to the use of unsuitable fuel. It is recommended to add a certain amount of cleaning agent when refueling. After cleaning, it is advisable to drive at high speed for a while, which helps increase exhaust volume and allows stronger airflow to remove larger carbon deposit particles. 2. Check the oxygen sensor: As an internal control unit of the car, the oxygen sensor mainly monitors the fuel-air ratio in the engine. Once damaged, it can cause an imbalance in the fuel-air ratio, leading to a sudden increase in fuel consumption. If the oxygen sensor is damaged, the exhaust pipe will emit darker-colored exhaust gases during driving, and the sensor should be replaced. 3. Regularly replace the three filters: During vehicle use, the oil filter, air filter, and fuel filter must be replaced regularly. If not replaced for a long time, they can become dirty and affect performance, sending incorrect information to the engine control unit, resulting in incomplete fuel combustion and increased engine carbon deposits.
Was this review help?
1
1
Share
More Forum Discussions

What is Parking Assist?

Parking assist system is an ultrasonic sensor embedded in the front and rear bumpers, with each sensor having a diameter of approximately 15mm. Here is an introduction to parking assist: 1. The ultrasonic detection signal emitted by the sensor will reflect when it hits an obstacle. After receiving the reflected signal, the sensor will promptly feed it back to the system for distance calculation, and remind the driver of the distance between the vehicle and obstacles outside the field of vision through sound, video, etc. 2. All vehicles need to be equipped with a parking assist system. Normally, when reversing, parking, or shifting the vehicle, the gap between the front and rear vehicles needs to be calculated accurately in centimeters, which cannot be estimated by the driver's vision alone. The parking assist system can detect obstacles outside the field of vision and inform the driver of the distance between the vehicle and the obstacle through certain signals.
19
0
Share

What Causes the Abnormal Noise Inside the Car When Driving on Bumpy Roads?

Abnormal noises inside the car when driving on bumpy roads mainly originate from two aspects: the suspension system and the braking system. Here is a detailed introduction: 1. Suspension system noise: The condition of the car's shock absorbers directly affects driving comfort and safety. Whether they need to be replaced depends on the mileage or service life. The service life of ordinary shock absorbers can reach 100,000 kilometers. If there is obvious abnormal noise when driving on bumpy roads, it is usually due to damaged or leaking shock absorbers, which need to be replaced. 2. Braking system noise: Braking noise occurs in various types of vehicles, sometimes even in new cars, especially in low-temperature environments. Most performance cars use high-temperature brake pads with a large friction coefficient. If the temperature is not reached, abnormal noise will occur, which can be resolved by replacing the brake pads.
7
2
Share

How to Remove the Front Seat Headrest of Volkswagen Tharu?

Here is the method to remove the front seat headrest of Volkswagen Tharu: 1. Locate the round button approximately five centimeters below the midpoint between the two steel tubes of the headrest. Press the circular plastic button beneath the headrest support rods, which functions as a small switch. 2. With one hand pressing the adjustment button, use the other hand to move the headrest support rods up and down while lifting the headrest upwards. The headrest can then be removed. Here is some related information: Car headrests are part of the mandatory national automotive certification and inspection requirements, with strict regulations on material, strength, energy absorption, position, and size. Current national standards only mandate the installation of headrests for front seats in passenger cars, while there is no compulsory requirement for rear seats. Similarly, international standards, such as those in the European Union, do not enforce mandatory headrest installation for rear seats.
12
0
Share

Should You Engage the P Gear or Pull the Handbrake First When Parking?

When parking, it is acceptable to either engage the P gear or pull the handbrake first. The P gear brakes the output end of the transmission. Due to the clearance in the components at the output end, on flat roads, whether you pull the handbrake or engage the P gear first makes no difference to the braking effect on the vehicle itself. However, the handbrake is a wear-prone component. For short-term parking on flat roads, simply engaging the P gear is sufficient to keep the vehicle stationary, and you may skip pulling the handbrake. When parking on a slope, if you engage the P gear before pulling the handbrake, the force from the incline can easily cause the clearance to lock up. Over time, this can also lead to wear on the component, making it difficult to shift gears when restarting the vehicle. Therefore, when parking on an incline, always remember to shift to N gear, pull the handbrake, and then engage the P gear.
18
5
Share

How to Install and Remove a Car Battery?

Steps for removing a car battery: 1. Turn off the vehicle engine and remove the key. 2. Disconnect the negative terminal cable from the battery. Reason: The negative terminal is disconnected first mainly because it serves as the ground connection. Once removed, you can proceed without any issues. However, if the positive terminal is disconnected first, there is a risk that improper handling may cause the wrench to come into contact with metal parts of the car body, resulting in sparks. This essentially creates a direct connection between the positive and negative terminals, leading to a sudden surge of extremely high current. In severe cases, this can blow the largest power fuse in the car body, with the most common consequence being the burning out of the car navigation system. 3. Disconnect the positive terminal cable from the battery. 4. Remove the battery protective cover, unscrew the battery's mounting bolts, and take out the battery for replacement. Steps for installing a car battery: Simply reverse the steps for battery removal.
4
5
Share

What Causes Abnormalities in the Reversing Radar?

Reasons for abnormalities in the reversing radar: 1. The reversing radar probe itself is faulty. 2. There is a fault in the connecting wiring of the reversing radar. 3. The vehicle's reversing radar system is malfunctioning. 4. The reversing radar probe is too dirty or has attachments. Note: The above issues need to be checked in order to properly repair the fault. Here is an introduction to the reversing radar: 1. The reversing radar on motor vehicles is a reverse collision avoidance radar, also known as a parking assistance device, mainly composed of ultrasonic sensors, a controller, and a display. 2. When the vehicle is preparing to reverse, it can provide the driver with information about surrounding obstacles, allowing the driver to fully understand the obstacles and helping to eliminate blind spots around the vehicle, thus preventing accidents caused by reversing.
7
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.