How to Solve the Leaking Issue in a Wrangler?

3 Answers
SanValerie
07/24/25 4:23pm
Leaking in the Wrangler's doors is generally caused by issues with the sealing strips. If the leakage is minor, replacing the sealing strips should suffice. For severe leaks, it may be necessary to realign the chassis. Below is more information about the Wrangler: 1. The Wrangler is a Chrysler Jeep model and represents the top-tier version of the Jeep Wrangler series. It is the most robust variant in the Jeep lineup, a true ORV (Off-Road Vehicle). 2. The 2015 Wrangler received a comprehensive upgrade to its audio system, enhancing the Alpine® audio system from a 6+1 subwoofer setup to an 8+1 configuration. Additionally, the 2015 Wrangler is equipped with a mechanical part-time four-wheel-drive system, allowing drivers to manually select between two-wheel and four-wheel drive modes based on road conditions by engaging or disengaging the transfer case.
Was this review help?
14
2
Share
LaBrooklyn
08/10/25 7:44am
As someone who has driven for many years, I think if a Wrangler is leaking, the first thing to check is the rubber seals around the door frames. When they age, they can easily crack and let water seep in. When the weather turns bad, feel around the door edges for any wet spots. If the seals are damaged, you can just spend a few dozen bucks to buy new strips and stick them on—it's a simple fix. Clogged drainage tubes are another common issue, especially the sunroof drain holes or door drainage holes. If dust and mud build up, water can backflow. Carefully unclog them with a thin wire or use compressed air to blow them out. If there's rust at the body welding points, it can also cause leaks—just apply some sealant to seal them. After washing the car, don’t forget to dry the seals to prevent them from cracking. Fix small issues promptly to avoid water accumulation and rust, which can lead to costly repairs. I once delayed fixing a leak, and the carpet ended up molding, even affecting the AC system.
Was this review help?
10
0
Share
Expand All
JaxsonDella
09/25/25 8:10am
After off-roading, my Wrangler always gets covered in mud, leading to water leaks. When mud clogs the sunroof drain tubes or door drain holes, water has nowhere to go and seeps into the cabin through gaps. Open the roof to check if the water channels have any cracks. If the seams on a soft top are loose, you can adjust the fasteners yourself or replace the top cover. Flattened door seals can also cause leaks. Regularly rinsing the chassis and drainage channels with a hose can prevent this. Don’t slack off on cleaning after off-roading—accumulated water can rust the frame and wiring, which is dangerous. After installing roof racks or wheels, unsealed gaps can also cause leaks. Check the gaps and seal them with adhesive to save money and hassle. Don’t make the same mistake I did by ignoring it, resulting in expensive repairs due to electrical shorts in the car.
Was this review help?
10
5
Share
Expand All
More Forum Discussions

What is the full name of Subject 4?

Subject 4, officially known as Subject 4 Theoretical Test or Driver's Theoretical Test, is part of the motor vehicle driver's license assessment. Below are the relevant details: Test Timing for Subject 4: Theoretically, you can schedule the Subject 4 test immediately after passing Subject 3, with no specific waiting period required. However, due to varying local policies, the interval between Subject 3 and Subject 4 may differ. In some regions, you can take Subject 4 right after passing Subject 3, meaning you could complete both tests on the same day. Other areas may require a one-week waiting period before scheduling Subject 4. Test Content for Subject 4: The exam covers safe and civilized driving practices, knowledge of safe driving under adverse weather and complex road conditions, emergency handling procedures such as tire blowouts, and post-accident response measures. Also referred to as the Theoretical Test or Driver's Theory Exam, Subject 4 evaluates 'driving ethics.'
18
5
Share

Is there a safety officer in the car during Subject 2 test?

There is no safety officer in the car during Subject 2 test, only staff members in the testing area. Your score is evaluated by the onboard electronic equipment, and you need to sign the document when you pass the test. Here is a detailed introduction about it: Subject 2, also known as the small road test, is part of the motor vehicle driver's license examination and refers to the field driving skills test. Test items include: stake test, slope fixed-point parking and starting, parallel parking, passing single-plank bridge, curve driving, right-angle turn, passing width-limited gate, passing continuous obstacles, driving on bumpy roads, narrow road U-turn, as well as simulated highway driving, continuous sharp turns on mountain roads, tunnels, rain (fog) weather, slippery roads, and emergency situation handling.
13
4
Share

How to Make Car Windshield Washer Fluid?

Here are the methods for making homemade windshield washer fluid: 1. Spring Windshield Washer Fluid: Prepare a 2.5-liter plastic bottle, 2 liters of purified water, 250ML of 95% medical alcohol, and 1-2 caps of detergent. Mix them thoroughly and it's ready for use. The detergent is mainly for removing sand and dust, while the alcohol accelerates water evaporation, ensuring quick cleaning of the windshield. 2. Summer/Autumn Windshield Washer Fluid: Use a 2.5-liter plastic bottle, 2 liters of purified water, 500ML of 95% medical alcohol, and 1 cap of detergent. The alcohol is very effective in removing insect residue. If you're in the city, you can top up the reservoir with purified water, but it's not recommended to dilute the mixture on highways as it may reduce effectiveness. 3. Winter Windshield Washer Fluid: A mixture of 20% 95-proof alcohol and 80% water has a freezing point around -10°C, suitable for early winter. A mixture of 20-30% alcohol and 60% water has a freezing point of -15°C. A mixture of 40-50% alcohol and 50-60% water can reach a freezing point of -25°C without freezing, meeting most winter needs.
12
4
Share

Can You Stall the Engine in Subject Two?

You only need to complete tasks such as reversing into a garage, parallel parking, stopping on a slope, turning at a right angle, and driving on a curve, then return to the starting point after the assessment. There is no need to stall the engine. Here is an introduction to Subject Two: 1. Introduction One: Subject Two, also known as the small road test, is part of the motor vehicle driver's license assessment and is the abbreviation for the field driving skills test. 2. Introduction Two: The test items include five mandatory tasks: reversing into a garage, parallel parking, stopping on a slope, turning at a right angle, and driving on a curve. Here are the precautions for Subject Two: 1. Introduction One: Do not wear items that obscure your face when taking photos, such as scarves, masks, hats, etc. 2. Introduction Two: When getting into the car, actively show your ID card, adjust the seat, turn on the left turn signal, fasten the seat belt, release the handbrake, and enter the test area only after hearing that the identity verification is successful. 3. Introduction Three: If the vehicle ahead is reversing into a garage, wait outside the arrow until the vehicle ahead moves to parallel parking before starting your test. 4. Introduction Four: For parallel parking, align with the reference point ahead, avoid pressing the solid lines on both sides, and keep the right wheel 20-50 cm away from the garage line. 5. Introduction Five: Wait for the vehicle ahead to exit before entering the curve driving test. If there is a vehicle ahead, wait outside the arrow. 6. Introduction Six: When starting on a slope, do not wait for the computer voice announcement because you must complete the starting action within 30 seconds. Do as you usually practice to ensure a smooth start without stalling or rolling back. 7. Introduction Seven: For turning at a right angle, control the speed carefully—do not go too fast. Align with the reference point, straighten the direction, identify the point ahead, and quickly turn the steering wheel fully to the left.
13
0
Share

Does coasting with the clutch fully depressed damage the clutch?

This is a standard operation. For manual transmission vehicles, braking involves fully depressing the clutch while simultaneously applying the brakes. During this process, there is inevitably a period of coasting, which does not inherently damage the vehicle. However, prolonged coasting in this manner carries certain safety risks. If braking is not intended for stopping, there's no need to depress the clutch—simply apply light brake pressure. Additional information: Reason: When the clutch is fully depressed, the engine and transmission are disconnected, causing the vehicle to lose power. This state imposes no wear on the engine or transmission. Braking in this condition does not harm the vehicle, as the engine and transmission are already disengaged. However, relying solely on the brakes for deceleration without engine braking increases the burden on the braking system over time, potentially compromising driving safety. Precautions: As the vehicle speed decreases, downshift sequentially through gears 6/5/4/3/2/1. Coasting in gear can achieve an average coasting distance of over 80% without fuel injection. This is because the vehicle's inertial force during coasting drives the transmission system and engine in reverse through the wheels. With no operational load, the fuel injection system can cease fuel delivery.
14
5
Share

What is the equivalent of 30 psi in atmospheric pressure?

30 psi is equivalent to 2 standard atmospheric pressures. Hazards of excessive tire pressure: Reduced tire friction and adhesion, affecting braking performance; Causes steering wheel vibration and deviation, reducing driving comfort; Accelerates wear on the central tread pattern, shortening tire lifespan; Increases vehicle vibration, indirectly affecting the lifespan of other components; Overextends tire cords, reducing elasticity and increasing the load on the vehicle during driving; Decreases puncture resistance. Sharp objects like nails or glass can easily penetrate the tire, leading to internal cracks or blowouts. Methods for insufficient tire pressure: If no damage is visible, inflate to normal pressure and reset the tire pressure system; If a puncture is found, promptly drive to a tire shop for repair and reinflation; If the tire pressure warning reappears after inflation without any punctures, it may be due to a leaking wheel rim deformation. Check and replace the rim if necessary.
8
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.