How to Solve the Issue of Low Volume in Car Bluetooth Calls?

1 Answers
Chiron
07/30/25 1:24am
When the phone has not been turned off for a long time, it is highly likely that the internal resources of the phone are heavily occupied. Restarting the phone can make it run smoothly. When Bluetooth maintains a high-frequency connection with the phone for an extended period, the connection may become unstable due to prolonged connection and changes in geographical location. Turn Bluetooth off and on again. When the Bluetooth headset is in charging mode, press and hold the button without releasing it. Reconnect the car Bluetooth.
Was this review help?
7
2
Share
More Forum Discussions

What are the tips for driving a manual transmission car on the highway?

The techniques for driving a manual transmission car on the highway include: 1. Do not shift gears when overtaking on the highway. Shifting gears in a manual transmission car requires depressing the clutch, which disconnects the power system from the transmission, cutting off the engine's power input to the transmission and causing the speed to decrease. 2. When braking, press the brake first and then the clutch. If you fully depress the clutch before braking, the car is effectively in neutral, and stopping the car relies solely on the brake pads, which increases the braking distance. 3. When entering the highway, after passing the toll booth, gradually increase the throttle to shift up through the gears. When reaching 4th gear, continue to press the throttle deeper. Do not rush to shift to 5th gear; wait until the RPM reaches around 3500 and the speed exceeds 70 km/h before shifting to 5th gear.
10
3
Share

How to Set the Time on a 7th Generation Accord?

To set the time on a 7th generation Accord, follow these steps: 1. Start the car and locate the button labeled "SOUND" on the audio control panel. Press and hold the "SOUND" button for 5 seconds until you hear a beep, then release it. 2. After the beep, the time display on the screen will start flashing. On the audio panel, find buttons 4, 5, and 6, which are labeled H, M, and R respectively, representing hours, minutes, and seconds. 3. Use the "NR" button and the "DISC-" button to adjust the time. 4. Once the correct time is set, press the "SOUND" button to save the settings.
18
4
Share

What Do the Numbers on Car Tires Mean?

Taking 225/60R1799H as an example, the meanings of the numbers and letters in the tire model are as follows: 1. 225 represents the section width, which can be simply understood as the width of the tire tread. 2. 60 represents the aspect ratio, which can be simply understood as the height of the tire sidewall. 3. R stands for the tire type code, with R indicating a radial tire. 4. 17 represents the rim diameter, meaning the tire is suitable for 17-inch rims. 5. 99 represents the tire's load index, indicating the maximum weight the tire can bear. 6. H stands for the tire's speed rating, indicating the maximum speed the tire can withstand.
4
3
Share

What to Do When the Engine Fuel Injector Fails?

If the fuel injector is faulty, the injector should be removed for repair. If the damage is severe, it should be replaced. After replacement, the injection pressure should be adjusted to 22-0.5Pa, ensuring good spray performance without dripping. Regularly clean the fuel filter to prevent excessive impurities in the fuel from clogging the injector. A faulty fuel injector can directly cause abnormal engine performance. Symptoms of failure include: (1) Black smoke from the exhaust pipe; (2) Uneven operation of each cylinder, causing noticeable engine vibration; (3) Decreased engine power; (4) Weak vehicle performance. To diagnose a faulty engine injector, let the engine idle and perform a fuel cut-off test on each cylinder sequentially. When the fuel supply to a particular cylinder is stopped, observe the engine's operation and sound. If the exhaust stops emitting black smoke and the engine speed changes after the fuel cut-off, it indicates a faulty injector in that cylinder. Once the engine injector fault is accurately diagnosed, remove the injector and test it on an injector calibration bench.
8
5
Share

What is the working principle of a hydraulic retarder?

The working principle of a hydraulic retarder is: 1. Working principle: The hydraulic retarder utilizes liquid damping to generate a retarding effect. The stator of the hydraulic retarder also serves as the retarder housing, which is connected to the rear of the transmission or the vehicle frame. The rotor is connected to the driveshaft via a hollow shaft, and both the rotor and stator are cast with blades. During operation, pressure is applied to the oil reservoir through the control valve, allowing the working fluid to fill the working chamber between the rotor and stator. When the rotor rotates, it exerts a torque on the stator through the working fluid. The counter-torque of the stator then becomes the braking torque of the rotor, the value of which depends on the amount and pressure of the working fluid in the chamber (determined by the braking intensity set by the control valve) and the rotational speed of the rotor. 2. Practical function: The kinetic energy of the vehicle is consumed by the friction of the working fluid and the impact on the stator, converting into heat energy and raising the temperature of the working fluid. The working fluid is circulated through a heat exchanger, transferring the heat to the cooling water, which is then dissipated through the engine cooling system. In vehicles equipped with hydraulic transmission, the oil reservoir, oil pump, heat exchanger (which needs to be enlarged in size), and the working fluid used in hydraulic transmission can be omitted. Therefore, hydraulic retarders are commonly used in vehicles with hydraulic transmission.
9
0
Share

What does the 'key' indicator on the car dashboard mean?

When the car dashboard displays 'KEY', it means the vehicle's computer cannot detect the key fob signal. Solutions: 1. Press both the lock and unlock buttons on the key. 2. Replace the key's battery. Additional information about car key functions: This smart key can emit infrared signals to open one or two doors, trunk, and fuel filler cap, and can also operate car windows and sunroof. More advanced smart keys resemble credit cards - when the driver touches the door handle, the central locking system activates and sends a wireless query signal. After the smart key card responds correctly, the door locks automatically open. The engine will only start when the central processor detects the key card inside the vehicle.
18
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.