How to Solve the Illuminated Engine Warning Light on the Dashboard?

What adhesive should be used for a detached car roof fabric?

For a detached car roof fabric, the selection of adhesive is as follows: 1. Soft foam fabric: Use solvent-based polyurethane adhesive or water-based polyurethane adhesive for soft foam fabric. 2. Hard foam glass fiber non-woven fabric: Use solvent-free polyurethane adhesive for hard foam glass fiber non-woven fabric. Additional information: Types of automotive adhesives: 1. Floor adhesive: (1) Floor adhesives are divided into hand-sewn and pre-formed types. (2) Well-made floor adhesives with good board type and craftsmanship can effectively prevent dust and dirt from penetrating into the carpet, but their waterproofing ability is slightly weaker. (3) Pre-formed floor adhesives are pressed in one go, with no seams in the middle, offering good leak-proof performance, but they may look less aesthetically pleasing when laid on uneven car floors. (4) Generally, floor adhesives are made of 3mm thick rubber products, available in colors such as gray, beige, and black. 2. Sealant: Provides good sealing performance under certain tightening forces, with excellent resistance to pressure, heat, and oil. It has good stability to media and does not corrode metals.

5

1

Share

How often should the antifreeze in a Mercedes-Benz be replaced?

Mercedes-Benz vehicles generally require antifreeze replacement every 2 years or 40,000 kilometers. This is just a reference interval. For commercial vehicles with higher mileage, the replacement cycle should be shorter. Since driving conditions vary for each vehicle, the actual replacement schedule should be determined based on usage. Regularly check the antifreeze level and top it up if insufficient. If suspended particles, sediment, or discoloration are observed in the antifreeze, replace it immediately and flush the system. Antifreeze replacement procedure: Before a complete antifreeze change, conduct a thorough inspection of all hoses for leaks or cracks, with special attention to the five-way connector pipe (named for its five connection points distributing antifreeze to different vehicle components). If any leakage is detected at this component, replace the hose or reseal the connection as needed. Drain the old antifreeze and flush the channels with clean water. Fill the coolant reservoir with water and continuously circulate it through the engine cooling system. Let the engine idle for 3-5 minutes to circulate the water. Initially, slightly pinkish water will flow out - continue flushing until the outflow runs clear. Remember to disconnect the heater hose to fully drain the heater core. Approximately one hour after draining, add new antifreeze through the radiator hose for rapid filling. Then pour another batch into the reservoir until nearly full. Run the engine for about 10 minutes - as air escapes from the cooling system, the fluid level will drop. Top up the antifreeze to the "MAXT" mark on the reservoir.

6

1

Share

Where to Schedule the Subject 4 Exam?

To schedule the Subject 4 exam, you can log in to the website of the vehicle management office in the student's region, click on the option for online exam scheduling, and select Subject 4 to make an appointment. Below is some information about Subject 4: 1. Definition: Subject 4, also known as the Subject 4 theory test or driver theory test, is part of the assessment for obtaining a motor vehicle driver's license. 2. Content: The test consists of 50 questions, primarily in the form of case studies, images, animations, etc., with a perfect score of 100 and a passing mark of 90. 3. Origin: After the implementation of the Ministry of Public Security's Order No. 123, the Subject 3 exam was divided into two parts: the road test and an additional safety and civilization knowledge test. Since this test is conducted after Subject 3, it is commonly referred to as the Subject 4 exam, although officially, there is no such term as Subject 4.

3

1

Share

Can China IV Motorcycles Be Licensed?

The registration period for China IV motorcycles is three months, during which they can be successfully licensed. Motorcycles are classified as motor vehicles and cannot be driven on the road without a license. If the registration is not completed within three months, a late fee must be paid for the motorcycle, and the license should be promptly obtained. The implementation of the China IV emission standard began on July 1, 2010, and the nationwide implementation of the China V standard started on July 1, 2017. Therefore, vehicles produced between 2011 and 2017 generally meet the China IV emission standard. However, this is not entirely the case, as emission standard timelines vary across different regions in the country. Starting from July 1, 2019, the national 'Limits and Measurement Methods for Motorcycle Pollutant Emissions (China IV)' stipulates that all motorcycles sold and registered must comply with the China IV emission standard.

5

Share

What to Do When You Run Out of Gas on the Highway?

Solutions for running out of gas on the highway are as follows: 1. Find a gas station: You can choose to exit the highway first and look for nearby gas stations. Often, there are many gas stations near highway exits. You can also use mobile navigation, as many gas stations are marked on mobile maps. 2. Call for rescue: If your car suddenly runs out of gas in the middle of the highway, you can call the emergency number 12122. This rescue number is nationwide, so it's common to encounter a busy signal. Just be patient and try calling a few more times. 3. Contact your insurance company: You can call your insurance provider. If you have purchased relevant insurance, you can enjoy free roadside assistance from the insurance company. However, while some rescue services are free, consumables like gasoline may incur charges. 4. Seek help from other vehicles: If you run out of gas on the highway, you can ask for help from passing vehicles. Simply park your car on the emergency lane and use a tube to transfer gas from another vehicle's tank to yours.

7

4

Share

What Causes the Burning Smell When Accelerating Hard in an Automatic Transmission?

Regarding the causes and solutions for the burning smell when accelerating hard in an automatic transmission, the following points are provided: 1. There might be a malfunction in the vehicle's electrical system. Solution: Pay attention to regular maintenance. When the maintenance light on the dashboard illuminates, it indicates that the vehicle should be taken for maintenance. 2. It could be due to previous aggressive driving, which may have caused severe wear and overheating of the brake pads, resulting in a burning smell. Solution: Routine maintenance requires changing the engine oil and other fluids, replacing the engine oil filter, and conducting a thorough inspection of the vehicle. 3. Aging of the vehicle's plastic pipes might be the cause. Solution: Replace the plastic pipes promptly and perform maintenance on the vehicle.

18

0

Share

How to Solve the Illuminated Engine Warning Light on the Dashboard?

What adhesive should be used for a detached car roof fabric?

How often should the antifreeze in a Mercedes-Benz be replaced?

Where to Schedule the Subject 4 Exam?

Can China IV Motorcycles Be Licensed?

What to Do When You Run Out of Gas on the Highway?

What Causes the Burning Smell When Accelerating Hard in an Automatic Transmission?

What is the Difference Between the Clutch and the Accelerator?

Can You Turn on the Air Conditioning Without Starting the Car?

Can a car with push-button start be stolen if left unlocked?

What is the coverage of vehicle damage insurance?