How to Solve the High Water Temperature Issue in Mercedes-Benz E200?

1 Answers
CamillaLee
07/29/25 9:21pm
Solutions for high water temperature in Mercedes-Benz E200: You can replace the coolant or clean the dirt on the surface of the radiator. Most car engines are water-cooled, and water-cooled engines rely on coolant for heat dissipation. The coolant in a water-cooled engine continuously circulates within the engine to carry away excess heat. The coolant follows two circulation paths inside the engine: a major cycle and a minor cycle. When the engine is just started, the coolant undergoes the minor cycle, during which it does not pass through the radiator for cooling, helping the engine to warm up quickly. The body dimensions of the Mercedes-Benz E200 are 5024mm in length, 1854mm in width, 1477mm in height, with a wheelbase of 3014mm.
Was this review help?
9
4
Share
More Forum Discussions

How often should Ford Mondeo tires be replaced?

Ford Mondeo tires should be replaced every 60,000 to 100,000 kilometers. Tires are often used under complex and demanding conditions, enduring various deformations, loads, forces, and high and low temperatures during driving. Therefore, they must have relatively high load-bearing performance, traction performance, and cushioning performance. The following points should be noted when replacing car tires: 1. Choose tires with the same specifications as the original ones installed on the car. 2. Replace two tires at the same time, and rebalance each wheel after replacement to ensure uniform mass distribution across all parts. 3. After replacing the tires, the aging cycles of the new tires and the valve stems may differ. Valve stems may develop issues that are not easily noticeable, so it is recommended to replace the valve stems when replacing the tires. 4. If using the original tires provided with the car, follow the manufacturer's installation requirements. If using non-original tires, the side with the production date should generally face outward.
7
3
Share

How to remove the bumper of a LANGDONG?

Steps to remove the bumper of a LANGDONG: 1. Remove the clips on the left and right inner liners and pry open the liners. 2. There is a screw on the inner side of each bumper corner; gently pry it open. 3. Open the hood and remove the clips on top of the bumper. 4. Finally, remove the clips and screws at the bottom. Below is some relevant information about car bumpers: A car bumper is a safety device that absorbs and mitigates external impacts, protecting the front and rear of the vehicle. Both the front and rear bumpers of a car are made of plastic, hence called plastic bumpers. Generally, a car's plastic bumper consists of three parts: the outer panel, the cushioning material, and the crossbeam. The outer panel and cushioning material are made of plastic, while the crossbeam is formed by stamping cold-rolled thin sheets into a U-shaped channel. The outer panel and cushioning material are attached to the crossbeam.
10
4
Share

What is the reason why the Prado air conditioner cannot be turned off?

Prado air conditioner switch is turned off, the compressor will stop. If it does not stop, it may be due to relay adhesion or a problem with the switch controlling the compressor. To use the air conditioner in the Prado, the A/C button is required, which is the air conditioner switch DUAL button. This button is used to independently set the temperature for the driver's seat and the front passenger seat. Pressing this button can switch from independent mode to joint mode. The following is the Prado air conditioner usage guide: 1. Adjust the air conditioner temperature: The "+" and "-" adjustment keys are located on the left and right sides of the screen, and each press can increase or decrease the temperature by 0.5℃. 2. Seat heating: The two buttons in the lower left and lower right corners of the screen are the seat heating buttons, which control the temperature adjustment for the driver's cabin and the passenger seat respectively. 3. Temperature zone control: The "DUAL" button next to the A/C button in the air conditioner cooling mode is the button for temperature zone synchronization control. 4. Footwell temperature: In the button bar at the bottom of the screen, click the middle "···" button to open the multimedia settings options above, and then you can adjust the footwell temperature. 5. Warm air and hot air activation: Before heating with the air conditioner, turn off the A/C button. Heating is completed through the glass heating wire and the temperature of the coolant, without the need for the compressor to work.
1
2
Share

What Causes Engine Shaking When Cold?

Engine shaking when cold is caused by: 1. Low temperature: The exhaust pipe and oxygen sensor are cold, preventing the vehicle's ECU from obtaining accurate data promptly, leading to errors in ignition and air-fuel mixture control, which weakens the engine's power output; 2. Carbon buildup in the engine: Carbon deposits on the throttle body have adhesion, preventing the fuel injection from reaching the required gasoline amount for combustion; 3. Worn spark plugs: Different ignition gaps cause power deviations among the cylinders. Methods to address cold engine shaking include: 1. Letting the car idle after a cold start to allow the engine temperature to rise; 2. Cleaning the throttle body and fuel injectors; 3. Replacing the spark plugs.
6
1
Share

Is the Tayron from FAW or SAIC Volkswagen?

Tayron belongs to FAW-Volkswagen. FAW-Volkswagen, officially known as FAW-Volkswagen Automotive Co., Ltd., was established on February 6, 1991. It is a large passenger vehicle manufacturing enterprise jointly operated by China FAW Corporation Limited, Volkswagen AG, Audi AG, and Volkswagen (China) Investment Co., Ltd. Below are the specifications of the Tayron: The vehicle has a length, width, and height of 4589mm, 1860mm, and 1660mm respectively, with a wheelbase of 2731mm. It is equipped with a CUG 2.0T high-power engine and a DBF 2.0T low-power engine, with maximum power outputs of 220 horsepower and 186 horsepower respectively, paired with a 7-speed dual-clutch transmission.
12
4
Share

What Causes Bad Odor in Car Air Conditioning?

The reasons for bad odor in car air conditioning are: 1. The air filter has not been cleaned for a long time, and the humid air during rainy seasons makes the filter damp and warm, leading to mold growth and a musty smell; 2. Outside air flows through the air conditioning system's pipes, where a small amount of residual moisture combines with dust in the air. If not cleaned for a long time, this can also lead to mold and produce a sour, rotten odor. Below are solutions to eliminate bad odor in car air conditioning: 1. Regularly clean the air conditioning system or replace the air filter to reduce mold growth; 2. Master the correct method of turning the air conditioning on and off. Generally, it is best to turn off the air conditioning 5 minutes before parking, then switch to natural air to quickly restore the car's internal temperature, preventing condensation inside the air conditioning pipes due to temperature differences after parking, thus keeping the pipes dry and preventing mold and fungus growth; 3. Use natural air fresheners. You can place fruits like pineapples, lemons, or apples in the car to help eliminate odors; 4. Frequently use the AUTO button on the air conditioning panel to maintain a relatively stable temperature inside the car, ensuring comfort and maintaining air quality.
5
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.