How to solve the abnormal noise of Roewe RX5 sunroof on bumpy roads?

2 Answers
Jess
07/29/25 2:15am
To address the abnormal noise from the Roewe RX5 sunroof on bumpy roads, first identify the cause of the noise. If the sealing ring is aged, it needs to be replaced with a new one. If the screws are loose, tightening them can resolve the issue. Here are the specific methods: 1. Turn on the vehicle's ignition, press the sunroof switch button, and ensure the interior and exterior are quiet. Observe the sunroof's movement path to check for obvious up-and-down fluctuations. If present, it indicates component aging, and the parts must be replaced. 2. Loose screws can cause roof and sunroof noises and even pose a risk of the sunroof falling off. The solution is simple: locate the sunroof screws and tighten them. 3. Due to prolonged use, debris particles may accumulate on the sliding tracks. When the sunroof moves along these tracks, it can rub against the debris, causing abnormal noise. Therefore, it is essential to keep the tracks clean. Apply lubricant to both sides of the sunroof tracks, paying extra attention to areas where noise was previously detected, as these spots experience the most friction.
Was this review help?
1
3
Share
BradyMarie
08/12/25 6:14am
I previously experienced squeaking sunroof noises on bumpy roads when driving an SUV, which was particularly annoying. My own solution was to first clean the sunroof guide rails with a clean, slightly damp cloth to remove dust and debris, preventing any jamming. Then, I sprayed some neutral silicone-based lubricant on the rails and gently opened and closed the sunroof a few times to distribute the lubricant evenly. If the sunroof's mounting screws were loose, I used a wrench to tighten them slightly, being careful not to over-tighten. If the noise persisted, it might indicate deformed guide rails or aging seals, in which case I recommend a professional inspection at a 4S shop. For daily maintenance, it's best to clean the sunroof monthly and drive slower on rough roads to minimize noise. Prevention is better than repair—don’t let minor issues escalate into major problems that affect your driving mood and cost more to fix.
Was this review help?
10
3
Share
Expand All
More Forum Discussions

Can the Great Wall Fengjun 5 be turned off while it is self-cleaning?

Great Wall Fengjun 5 can be turned off while it is self-cleaning. The self-cleaning function of the car is controlled by the computer, and turning off the car will not hinder the operation of the self-cleaning function. After the car self-cleans, it can effectively reduce the pollution of particulate matter in the exhaust emissions to the air and improve the cleanliness of the air. The time for car self-cleaning: There is no specific requirement for the time of car self-cleaning, which needs to be determined according to the use of the car and the driving environment. Self-cleaning is also divided into manual and automatic. Automatic cleaning vehicles will have active prompts, and manual cleaning once every 15,000 to 20,000 kilometers is more reasonable. If the engine shakes while driving, it needs to be cleaned and self-cleaned. The operation method of car self-cleaning: Turn on the ignition switch, connect the power supply, and press and hold the DPF regeneration switch behind the steering wheel until the dashboard prompts to start the vehicle and idle, then start the vehicle. The engine speed will automatically maintain at 2000 rpm until the dashboard shows that the self-cleaning is completed, and then turn off the car.
3
5
Share

How to reset the maintenance light on Audi A6?

Here is the method to reset the maintenance light on Audi A6: 1. First, enter the vehicle option on the main page and select settings and services. 2. Then click to enter the maintenance cycle submenu interface and select reset oil change cycle. Here are some related information about vehicle maintenance: 1. The internal parts of the vehicle will gradually wear out as the driving time increases. To ensure the normal operation of the car, the manufacturer has set up some reminder indicator lights. After reaching a certain mileage, it is necessary to replace the parts in time. After successful replacement, the car maintenance light needs to be reset. 2. The function of the maintenance light is to record the mileage of some important parts, like a timer, to remind the car owner and maintenance staff. If the relevant parts are replaced without resetting the maintenance light, it will not affect the performance of the vehicle, but it will cause trouble for the next replacement of car parts, as the exact usage time of the new parts cannot be known. 3. Generally, during vehicle maintenance, the maintenance personnel will first check the lights. Check whether the front lights are working normally and whether the rear lights are working normally. The next step is to open the engine compartment. Check whether the various liquid levels in the engine compartment are normal, then lift the vehicle to check the tires, etc. Finally, perform a computer detection and reset.
1
4
Share

How to Check Tesla Hardware Version?

Tesla hardware version can be checked by first removing the glove compartment in front of the passenger seat. After opening it with tools, you will see a label indicating the hardware version, which can then be verified against the codes on the official website. Here is some relevant information: 1. Since late 2016, Tesla has comprehensively upgraded the configurations of all its production models, equipping them with the 2.0 autonomous driving hardware system, which utilizes Tesla's independently developed deep learning neural network vision technology. It is believed that full autonomous driving will be achieved in the near future. 2. This system is currently the most powerful driving computer in all mass-produced models, and Tesla's S, X, and 3 models all use this hardware, significantly reducing driver pressure and improving the driving experience.
20
3
Share

What is the difference between Crystal White and Pearl White?

Pearl White and Sparkling Crystal White car paints are different, with the following distinctions: 1. Different appearance colors: Pearl White appears slightly yellowish under the sun, resembling the inner wall of a clam shell, with relatively lower brightness; Sparkling Crystal White appears very white under the sun, subtly reflective among white paints, with relatively higher brightness. 2. Different compositions: Pearl White contains mica coated with titanium dioxide and pearl powder; Sparkling Crystal White contains silver powder, with luminescent white particles mixed in and fluorescent whitening agents. Both belong to metallic paints.
13
0
Share

China V Diesel Quality Standards?

China V diesel standards specify the following parameters: color 3.5, oxidation stability 2.5mg/100ml, sulfur content 0.001%, acidity 7mgKOH/100ml, 10% distillation residue carbon content 0.3%, no mechanical impurities, polycyclic aromatic hydrocarbons content 11%, flash point (closed cup) 55°C, 50% evaporation temperature 300°C, 90% evaporation temperature 355°C, 95% evaporation temperature 365°C. Below is additional information: 1. Anti-knock quality: Determined by cetane number. Low cetane number makes fuel difficult to ignite with long ignition delay and unstable engine operation, while higher cetane number provides better ignition performance, shorter ignition delay, more uniform combustion and smoother operation. Excessively high cetane number may cause incomplete combustion and black smoke. 2. Evaporation characteristics: Evaluated by distillation range and flash point. Lower 50% evaporation temperature indicates more light fractions in the fuel, making diesel engines easier to start. Lower 90% and 95% evaporation temperatures indicate fewer heavy fractions. National standards specify that -35 and -50 grade light diesel must have flash points not lower than 45°C. 3. Flow characteristics: Evaluated by viscosity, pour point and cold filter plugging point. Too low viscosity may cause leakage between high-pressure fuel pump plunger and barrel, while too high viscosity makes fuel supply difficult. 4. Corrosiveness: Evaluated by sulfur compounds and sulfur content. Stability is evaluated by total insolubles and 10% distillation residue carbon content.
3
1
Share

What is the direction of car tire screws?

The direction for tightening car tire screws is clockwise, while the direction for loosening them is counterclockwise. Signals indicating the need for car tire replacement: 1. Tread wear approaching the wear indicator: Any brand of tire will have a wear indicator at the bottom of the tread grooves. Generally, the wear indicator height for passenger car tires is 1.6 mm, while for heavy-duty tires it is 2.4 mm. Some car owners believe that as long as the tire is not punctured, they can continue to use it even if the tread pattern is almost worn out. Such old tires are actually very dangerous. When encountering wet or slippery roads, the tread pattern cannot completely drain the water beneath the tire, which can easily lead to loss of vehicle control. 2. Tire damage such as cracks or bulges: Tire damage includes tread cracks, tread bulges, missing tread rubber, severe sidewall wear, and multiple punctures by foreign objects. Especially in the case of bulges, the tire is at risk of bursting at any time. As soon as these types of damage are noticed, car owners should promptly take their vehicle to a professional tire shop for inspection and replace the tires as necessary. 3. Tire age expiration: The typical service life of a tire is around 5 years. Beyond this period, the tire begins to age. The main signs of tire aging are surface hardening followed by the appearance of cracks. Aged tires lose their elasticity, and continued use can lead to tread deformation, posing a risk of tire blowout.
17
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.