How to Solve the Abnormal Noise During Acceleration in Mercedes-Benz E260?

1 Answers
DelEmmett
07/29/25 10:42pm
Mercedes-Benz E260 acceleration abnormal noise causes and solutions: Fuel pump motor abnormal noise: When there is internal wear or impurities in the fuel pump motor, abnormal noise will occur when accelerating. Solution: Replace the fuel pump. Throttle body abnormal noise: Modern throttle bodies use electronic throttle control, where the motor naturally controls the opening and closing of the throttle valve. When the motor gears wear out, insufficient engagement causes abnormal noise. Excessive carbon deposits or sludge in the throttle body can also lead to abnormal noise. Solution: Clean the throttle body; if the motor is damaged, disassemble the throttle body and replace the servo motor. Accelerator pedal bearing lubrication issue causing abnormal noise: Clutch release bearing damage leads to incomplete clutch disc separation, causing abnormal noise. Solution: Apply grease to the bearing for lubrication. Remove the clutch and replace the release bearing.
Was this review help?
3
5
Share
More Forum Discussions

What should the following vehicles do when there is an accident at a traffic light intersection?

The safest and most reliable way is to stop and wait. In such a situation, you cannot change lanes or make a U-turn, so just stop and wait. If some drivers have urgent matters, they can choose another way to detour by borrowing the opposite lane. Drivers who borrow the opposite lane should make some preparations. For example, when borrowing the opposite lane, it is best to be within the range of surveillance cameras, which can serve as evidence for reconsideration.
5
3
Share

How to Repair a Cracked Cylinder Block?

First, use coarse sandpaper to remove the rust around the crack in the cylinder block. When sanding to a certain extent, you can locate the end of the crack. Proceed directly with welding a repair plate. Pay attention to any warping at the welding site. If there is any, be sure to hammer the welded area while it's still hot to avoid leaving any welding slag. After the repair, place an asbestos gasket between the repair plate and the cylinder block (or cylinder head), and then apply a layer of lubricating oil on both sides.
2
5
Share

What is the method for reinstalling the spare tire in a Ford Focus hatchback?

Adjust the jack to the appropriate height; Insert the wrench head into the jack handle; Place the jack back into the trunk and secure it firmly using the rightmost hole (do not clip the wrench handle's fastener at this stage). After tightening the screw, clip the fastener on the wrench handle onto the jack handle; Return the spare tire to the trunk and secure it using the leftmost screw hole at the bottom of the trunk.
12
1
Share

What Vehicles Are Suitable for 89 Octane Gasoline?

Old Liberation trucks use 89 octane gasoline. Introduction: Gasoline is a volatile, flammable liquid hydrocarbon mixture separated from petroleum, used as fuel. Gasoline Usage Precautions: Gasoline is somewhat toxic; do not siphon it by mouth or deliberately sniff gasoline vapors. Monitor quality changes during long-term storage, particularly guarding against aging. When vehicles operate in hot summer regions, vapor lock may occur. Enhance engine cooling and ventilation accordingly. If necessary, insulate the fuel pump and fuel inlet pipe or apply drip cooling.
2
1
Share

How to Align the Timing Chain of a Toyota Corolla?

Adjust the electrical breaker contact gap to within the range of 0.35 to 0.40 millimeters. Locate the top dead center of the first cylinder's compression stroke and loosen the first cylinder's spark plug. Determine the position where the breaker contacts just begin to open, then loosen the fixing screw of the distributor housing. Connect the high-voltage wires according to the firing order. If the engine emits a brief and slight detonation sound that immediately disappears, the ignition timing is appropriate.
17
5
Share

How to Check the Engine Oil Level of Huasong 7

Pull the oil dipstick out of the dipstick tube; wipe the oil dipstick clean; insert the oil dipstick back into the tube until it reaches the stop position, then remove it; the oil level should be between the lower and upper marks. This can be done using the multifunction buttons on the left side of the steering wheel. Turn on the ignition switch. Repeatedly press the system selection button, which is the left and right buttons. The vehicle should be parked on level ground; if the engine is at normal operating temperature, turn it off for at least 5 minutes.
19
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.