How to Solve Engine Noise?

1 Answers
DeJoshua
07/29/25 5:17pm
Methods to solve engine noise are as follows: 1. If the engine noise is loud and you want to reduce it, you can install soundproofing cotton on the engine cover, which can effectively block part of the noise. You can also install soundproofing cotton inside the car doors to block some noise. 2. There are many reasons for loud engine noise, and some cars have inherently noisy engines from the factory. 3. Most noisy engines are direct-injection engines, and many direct-injection engines produce a ticking sound during operation. This is actually normal and is the sound of the high-pressure fuel pump working.
Was this review help?
4
0
Share
More Forum Discussions

Why does the gasoline engine water pump lack suction?

Reasons for the gasoline engine water pump lacking suction: 1. Insufficient priming water: Before starting the pump, the pump (including the inlet pipe) should be filled with water. Otherwise, insufficient priming water or air inside the pump will prevent it from drawing water. The solution is to fill enough priming water and exhaust all air from the pump. 2. Inlet pipe leakage: Leakage mainly occurs at the connection between the inlet pipe and the pump body. Check if the rubber gasket is intact, tighten all connecting bolts, and seal the leakage point. 3. Filter head blockage: During installation and use, the filter head often gets clogged by mud, weeds, leaves, or other debris, preventing water flow. Remove the filter head for cleaning. To prevent re-clogging, cover the filter head with a metal mesh to block debris. 4. Shaft (oil) seal leakage: The shaft seal, made of oil-resistant rubber, may wear out over time, causing leakage. Replace the shaft (oil) seal to restore operation. 5. Low voltage: Low voltage reduces water output. Avoid using the pump during peak electricity hours and use larger cross-section wires. Excessive impeller clearance: The impeller clearance is affected by the conical ring. If the clearance is too large, adjust it or replace the conical ring. 6. Installation position too high: If the pump is installed too high, the filter head may be too shallow in the water, easily sucking in air and causing cavitation. It may also exceed the pump's specified lift capacity, resulting in insufficient water output.
20
5
Share

What is the difference between pearl white and white?

The difference between pearl white and white car paint: 1. Different colors: Pearl white and white are two types of car paint colors. Pearl white paint contains mica powder inside, which reflects glossy mica particles under sunlight, making it appear very vibrant. In contrast, white car paint does not contain mica powder; the paint is pure white from inside to out and does not emit dazzling colors under sunlight. 2. Different processes: Pearl white is a type of metallic paint, while white car paint is ordinary paint without metallic luster. From a long-term usage perspective, ordinary white car paint tends to turn yellow over time, whereas pearl white paint may show color differences when touched up due to its unique properties. 3. Different prices: Because pearl white contains mica paint, it looks more attractive and is slightly more expensive to repair. Pure white car paint is not as expensive and does not incur such high costs during repairs.
12
1
Share

Will the Car Stall if You Only Press the Brake?

Only pressing the brake without engaging the clutch will cause the car to stall because the clutch is not fully disengaged. If the brake is pressed hard, the clutch won't be engaged. At this point, the power transmission is blocked by the locked wheels, and the car will stall due to the reaction force. Typically, when decelerating a manual transmission car, you should first press the brake, then engage the clutch, and begin slowing down. Only by pressing the clutch can the engine be separated from the transmission, ensuring the car doesn't stall when it comes to a stop. Reasons for Vehicle Stalling: Automatic transmission stalling is mainly caused by using low-quality fuel. You can refuel with high-quality fuel at reputable gas stations, such as using 97-octane gasoline. Although it is more expensive, it ensures longer vehicle lifespan and better driving performance. Thoroughly clean the fuel system, including the fuel injectors, throttle body, and fuel tank. The issue may be due to poor fuel quality, excessive gum deposits, or clogged fuel lines, leading to inadequate fuel flow. The main reason for stalling during idle is excessive dust in the air. When the engine is running, a large amount of dirt accumulates on the idle control valve and throttle body. Excessive dirt buildup can cause low idle speed, unstable idle, or stalling while driving. To fix this, simply clean the idle control valve. Fuel line obstruction is also a common cause of stalling while driving.
9
5
Share

What does the low beam symbol look like?

The low beam symbol is green. Here is more information about low beams: 1. Introduction: Low beams are designed for close-range illumination, with design requirements including a wide irradiation range (160°), short irradiation distance, and non-adjustable focus. 2. The following situations require the use of low beams: (1) Driving in areas without streetlights at night, or during dusk when it's getting dark or dawn when light is just appearing, low beams must be turned on. (2) In conditions of heavy fog, snow, or heavy rain where visibility is obstructed, low beams must be used even during the day. (3) In some areas where there is lighting but the brightness is insufficient, low beams should also be turned on.
7
4
Share

What Causes the Clutch Pedal Not to Return to Position?

The reasons for the clutch pedal not returning to position are: 1. Air in the hydraulic system, causing excessive clutch travel and poor return; 2. Aging clutch spring, which occurs when the vehicle has been used for a long time; 3. Contaminated clutch fluid, leading to clogged oil passages and resulting in the pedal not returning. The clutch pedal is the control device for the manual transmission clutch assembly and serves as the human-machine interface between the car and the driver. It is one of the five major controls in driving, whether during learning or normal operation, and is used very frequently. For convenience, it is commonly referred to as the 'clutch.' Proper operation of the clutch directly affects the vehicle's starting, gear shifting, and reversing.
18
1
Share

Can I get a refund for the tuition fee if I don't take the driving test after registering?

You cannot get a refund for the tuition fee if you decide not to take the driving test. Below is relevant information about the driving test process: 1. Driving test procedures: registration, traffic rules study, subject one test, subject two test, subject three test, subject four test. 2. Test content: The test subjects include three items: traffic regulations and related knowledge, field driving, and road driving (including safe and civilized driving). Specific contents include reversing into a garage, turning around on a narrow road, parallel parking, stopping and starting on a slope, turning at a right angle, driving on a curve, emergency braking, tunnel, taking a card at a toll booth, driving straight, changing lanes, passing through intersections, and parking by the roadside.
2
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.