How to Shift Between D and S Gears in an Automatic Transmission?

What are the reasons why a sedan cannot start?

The reasons why a sedan cannot start are as follows: 1. Battery depletion: If the car battery is dead, the car will not start. There are many reasons for battery depletion, such as battery water issues, battery failure, or prolonged parking, all of which can lead to a depleted car battery. 2. Ignition system failure: The function of the ignition system is to provide high voltage to the spark plug to ensure the car runs. If the car does not start and the battery is not the issue, it is likely that the ignition system has failed. Poor connections or high-voltage leakage can cause faults, affecting the car and making it difficult to start. 3. Low temperature: Most winters are quite cold, and it is common for cars not to start. In such environments, the viscosity and rotation speed of the car's engine oil decrease, and the battery's ignition energy also drops. As a result, flammable gases cannot form, making it hard to start the car. 4. Engine carbon buildup: Carbon buildup can make it difficult to start the vehicle. There are many reasons for engine carbon buildup, such as water in gasoline, poor fuel quality, or poor valve sealing. 5. Starter motor aging: If the car is hard to start, it may be due to an aging starter motor. If the starter motor has been used for too long, it can age, leading to weak starting or failure to start. Therefore, it is important to replace the starter motor regularly and avoid using it for too long.

12

3

Share

What is the Function of Engine Start-Stop?

Engine start-stop function: By equipping a traditional engine with an enhanced motor featuring idle start-stop capability, the engine completely shuts off when the vehicle meets idle stop conditions. When the vehicle needs to move forward again, the idle start-stop motor system quickly responds to the driver's start command, rapidly restarting the engine with seamless transition, thereby significantly reducing fuel consumption and exhaust emissions. Below is more information about engine start-stop technology: 1. Engine start-stop technology automatically shuts off the engine when the vehicle comes to a temporary stop during driving; when it's time to proceed, the system automatically restarts the engine. 2. Working principle: When the vehicle stops due to traffic congestion or at an intersection, the driver presses the brake pedal and shifts to neutral. At this point, the Start/Stop system automatically checks that the engine is idling without being in gear, the wheel speed sensors of the anti-lock system show zero, and the electronic battery sensor indicates sufficient energy for the next start. Once these three conditions are met, the engine automatically stops rotating.

15

4

Share

Why Does the Car Sound Get Louder?

Here are the main reasons why a car's sound gets louder: 1. Too much engine oil: This increases the instantaneous working resistance of the engine, thereby increasing the rotational resistance of the crankshaft and reducing the engine's output power. Additionally, excess oil can enter the combustion chamber and participate in combustion, leading to oil burning, blue smoke emission, increased fuel consumption, and a louder car sound. 2. Incorrect oil type: If you previously used fully synthetic oil and now switch to mineral oil, it can cause the car sound to become louder and the engine to behave abnormally. Counterfeit or inferior quality oil can cause significant damage to the engine. It is essential to strictly follow the oil type recommended in the maintenance manual when adding oil.

9

5

Share

What does 'hold' mean in a car?

The 'hold' in a car refers to the automatic parking function. The working principle and usage method of automatic parking are as follows: Working principle of automatic parking: The automatic parking function provides accurate parking force through a slope sensor controlled by the controller. During startup, the parking control unit calculates information provided by sensors such as clutch distance, clutch engagement speed, and throttle pedal. When the driving force exceeds the driving resistance, the parking brake is automatically released, allowing the car to start smoothly. Usage method of automatic parking: When the driver has fastened the seat belt, the driver's side door is closed, and the engine is running, pressing the automatic parking switch activates the function from off to standby mode. When the brake pedal is depressed to a certain depth and the vehicle has come to a complete stop, the automatic parking function switches from standby to parking mode. While in parking mode, selecting the appropriate forward or reverse gear and pressing the accelerator pedal will cause the automatic parking to release automatically based on the slope gradient.

19

1

Share

Where is the windshield washer nozzle located?

The windshield washer nozzle of a car is located under the hood, inside the engine compartment near the bottom of the windshield. The specific steps to locate it are as follows: 1. Open the driver's door of the car. 2. Pull the hood release lever located on the left side of the driver's leg area. 3. Lift the car's engine hood upward. 4. Secure the engine hood with the support rod to ensure it is firmly held in place and to prevent any hazards during operation. 5. The windshield washer nozzle is situated under the hood, inside the engine compartment near the bottom of the windshield.

3

5

Share

Do Plug-in Hybrid Vehicles Need to Be Charged?

Plug-in hybrid vehicles do require charging. Here are the specific details: 1. In simple terms, a plug-in hybrid electric vehicle (PHEV) is a type of vehicle that falls between a pure electric vehicle and a traditional fuel-powered vehicle. It is equipped with both the internal combustion engine, transmission, drivetrain, fuel system, and fuel tank of a conventional fuel-powered car, as well as the battery, electric motor, and control circuitry of an electric vehicle. Moreover, its battery capacity is sufficient to support driving in pure electric mode for a certain distance and includes a charging port. 2. In principle, plug-in hybrid vehicles can operate without being charged because when the battery is depleted, the engine can drive a generator to produce electricity. This electricity is then directly delivered to the electric motor via the motor controller, which in turn drives the vehicle. The power battery can also be charged externally. If the battery pack becomes ineffective or unusable, the engine alone can drive the electric motor to power the vehicle. Additionally, the power battery can be charged while the vehicle is parked. 3. However, due to the presence of the battery, plug-in hybrid vehicles are significantly heavier than traditional gasoline-powered vehicles. When the battery is depleted, the fuel consumption over the same distance is higher compared to conventional gasoline cars. Therefore, it is recommended to charge the vehicle promptly to achieve fuel-saving purposes. 4. Under normal circumstances, a typical plug-in hybrid vehicle needs to be charged every 2 to 3 days, with the charging schedule arranged according to individual usage scenarios.

3

5

Share

How to Shift Between D and S Gears in an Automatic Transmission?

What are the reasons why a sedan cannot start?

What is the Function of Engine Start-Stop?

Why Does the Car Sound Get Louder?

What does 'hold' mean in a car?

Where is the windshield washer nozzle located?

Do Plug-in Hybrid Vehicles Need to Be Charged?

What causes the yellow exclamation mark light to illuminate in an Audi?

Why is the air conditioning in a Ford car not cooling?

What is the L gear in a car?

What should be paid attention to when registering for a driving school?