How to Set Up the Digital Instrument Cluster on the 2021 Lavida?

1 Answers
Perry
07/30/25 10:32am
Rotate the adjustment knob; turning it counterclockwise to the end adjusts the hour, and a brief rotation of this knob allows for one-hour increments. Repeatedly press and hold the reset button (for more than 2 seconds) to adjust the brightness of the instrument cluster backlight separately. Briefly press button A on the windshield wiper lever after turning on the ignition to select the memory.
Was this review help?
1
4
Share
More Forum Discussions

Does a Faulty Exhaust Valve Cause Engine Oil Burning?

A faulty exhaust valve can lead to engine oil burning issues, as well as problems like engine idling vibrations and stalling. The main causes of exhaust valve damage include: poor quality of the valve itself, improper maintenance, low-quality fuel, and prolonged use leading to aging. More details are as follows: 1. The exhaust valve, also known as the pressure control valve, is installed between the compressor outlet and the condenser inlet. It helps improve heat transfer efficiency inside the condenser and evaporator. 2. The exhaust valve effectively reduces the NOX content in exhaust emissions. By recirculating exhaust gases into the combustion chamber, it lowers the internal temperature of the cylinder, thereby inhibiting NOX formation and reducing NOX levels in the exhaust. 3. Engine oil burning may also be caused by: faulty valve stem seals, excessive carbon buildup inside the engine, low-quality fuel, a dirty throttle body, overfilled engine oil (exceeding the maximum mark), or a clogged oil filter. 4. Symptoms of engine oil burning include: blue smoke from the exhaust pipe, vehicle vibration during idling, and severe oil loss within regular maintenance intervals.
16
5
Share

What type of rear suspension does the C-TREK Weiling use?

C-TREK Weiling adopts a compound torsion beam non-independent suspension. Here is the relevant introduction about torsion beam non-independent suspension: 1. The application range of torsion beam non-independent suspension is not very extensive, because this type of suspension has relatively high rigidity, which affects driving comfort to a certain extent. 2. Torsion beam non-independent suspension connects the two rear wheels of the car on one axle. If the car is driven on roads with poor conditions, the fluctuation generated at the rear of the car will be relatively large, affecting the comfort of passengers. 3. During actual driving, if one side of the car's wheels generates fluctuation, the wheels on the other side will also fluctuate simultaneously. 4. The structure of torsion beam non-independent suspension is relatively simple, with lower production and manufacturing costs and smaller space occupation. Therefore, many compact cars or small cars use this type of suspension. 5. The comfort of torsion beam non-independent suspension is relatively poor, but the quality of the suspension used in a car is not determined by the suspension itself. The tuning of the suspension must also be considered. A more complex suspension structure does not necessarily mean better performance; comprehensive consideration of multiple factors is required.
19
0
Share

Are Car Spark Plugs the Same?

Car spark plugs are not the same. When replacing spark plugs, one should not only focus on the material and the number of electrodes but also pay attention to the heat range of the spark plug. Each brand's heat range corresponds to specific vehicle models. When purchasing, ensure the heat range matches your vehicle model; otherwise, it may cause varying degrees of impact. The main types of spark plugs include: standard spark plugs, extended tip spark plugs, electrode spark plugs, seat spark plugs, pole spark plugs, and surface gap spark plugs. Steps for replacing spark plugs: Open the engine hood, lift the plastic cover of the engine, and remove the high-voltage wires. Mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing, check for any external debris like leaves or dust and ensure they are cleaned thoroughly. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Install the removed high-voltage wires according to the firing order, and then secure the cover plate.
16
2
Share

How to Replace the Cabin Air Filter in a 2014 Sagitar?

14 Sagitar cabin air filter replacement steps are as follows: 1. Move the front passenger seat to its rearmost position. Unscrew the two plastic nuts counterclockwise by hand, then gently pull out the thin black partition panel. 2. Using a flashlight, you'll find a plastic bracket underneath. Push the bracket parallel to the right to release the clip. 3. After removing the cover panel, slowly pull out the cabin air filter by both ends, noting its orientation, then install the new one accordingly. The functions of the cabin air filter are as follows: 1. Ensures the filter fits tightly against the housing to prevent unfiltered air from entering the cabin. 2. Filters out solid impurities from the air such as dust, pollen, and abrasive particles. 3. Adsorbs moisture, soot, ozone, odors, carbon oxides, SO2, and CO2 from the air. 4. Prevents windshield fogging to maintain clear visibility for safe driving; provides fresh air to the cabin to protect occupants from inhaling harmful gases; effectively sterilizes and deodorizes.
4
0
Share

How to Adjust the Headlight Height of the New Teana?

The new Teana does not have a headlight height adjustment button. To adjust the headlight height, you need to manually adjust it from the front headlight position. Open the engine compartment, and you will find two plastic screws at the back of the headlights that can be adjusted for height. By turning these screws, you can adjust the headlight height to the desired position. The specific steps for adjusting the headlights are as follows: 1. Generally, headlight adjustment involves adjusting the height. The adjustment is done via the horizontal adjustment screws located at the back of the headlights in the engine compartment. 2. Tools you will need: a tape measure, masking tape, a Phillips screwdriver, and a hex socket. 3. Headlight height adjustment should not be done arbitrarily. Find a flat area with a vertical white wall—such as an underground parking lot. Face the white wall, drive the car slowly straight toward it, and stop when the front of the car is as close to the wall as possible. Mark a vertical line on the wall corresponding to the centerline of the car's front. 4. Open the hood and look at the back of the headlights. Pay attention to the height and adjust it to the appropriate position.
13
1
Share

Is the Chery Tiggo 8's dual-clutch transmission dry or wet?

Chery Tiggo 8 is equipped with a dry dual-clutch transmission. The dry transmission transmits power through multiple friction plates and metal diaphragm plates connected to the input shaft. Power is transmitted when the friction plates and diaphragm plates are pressed together, and power transmission is interrupted when they are separated, which is the same principle as manual transmissions. Dry and wet dual-clutch transmissions share the same power transmission principle, but the working environments of the clutch driving plates and driven plates differ. The dry type operates in air, while the wet type works in oil. Dry dual-clutch transmissions have higher transmission efficiency, but since they can only rely on air for cooling, they are prone to overheating and wear in stop-and-go traffic conditions due to insufficient airflow. Wet dual-clutch transmissions are more durable and less likely to overheat. A clutch cooled by air is called a dry clutch. In use, the clutch should be able to engage and disengage from the power source easily and freely, and should not overheat even when operating in a semi-engaged state for short periods. Because dry clutches are not affected by the resistance of engine oil, they generally have faster engagement response and slightly stronger engagement force. Also, due to the lack of oil cooling, dry clutches usually adopt an exposed design for heat dissipation.
6
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.