How to set up automatic locking for Volkswagen Magotan?

1 Answers
McErin
07/30/25 8:31am
Magotan automatic locking setup method is as follows: 1. Set in the central control screen car menu, where the automatic locking function is available. 2. Find the "Auto Lock" option and tick it, so that the doors will automatically lock while driving. Here are some related information: 1. The purpose of the automatic locking function is anti-theft. It allows the doors to lock quickly after starting to drive, preventing door-pull robberies during traffic jams or at red lights, providing a certain level of security. Its advantage is that it protects child passengers inside the car, preventing young children from opening the door handles while the car is in motion. 2. The driving automatic locking is also called speed-sensitive automatic locking: it is an electronic device that automatically presses the lock button on the door when the vehicle speed reaches the value set by the computer, preventing accidental door opening. That is, when the speed reaches a set value, the car locks automatically. The set value is generally determined by the manufacturer, mostly between 10-20km/h.
Was this review help?
8
4
Share
More Forum Discussions

How to Deal with Scratches on White Car Paint?

Body scratches can be divided into several situations, each requiring different treatment methods: 1. Fine hairline scratches: Remove them using wax and fine cutting abrasives. Principle: The abrasives are as fine as nanometer level, which will not damage the original paint protection layer. 2. Light scratches: Use fine polishing wax to repair these minor scratches. Principle: Rearrange the molecules of the car's surface paint and move the edge surface paint to repair the wound. 3. Moderate scratches: Drive the car to a repair shop for professional treatment. During daily driving, try to avoid areas with high corrosiveness, such as seasides, roads with de-icing salt, newly paved asphalt roads, etc.
17
0
Share

Does the Civic 220 have VTEC?

Civic 220 does not have VTEC technology because VTEC is designed for naturally aspirated engines, while the Civic 220 uses a turbocharged engine. Below is a detailed introduction to VTEC: How VTEC works: In the intake camshaft, in addition to a pair of cams and rocker arms for two valves, there is also an additional higher intermediate cam and corresponding rocker arm. The three rocker arms contain small pistons controlled by hydraulic pressure. It can simultaneously control both the valve opening/closing timing and lift under different conditions. Models that use VTEC: VTEC and i-VTEC engines are used in many of Honda's naturally aspirated engine models. For example, the eighth-generation Accord 2.4L and Honda Lingpai 1.8L.
6
5
Share

What are the methods for replacing coolant?

Coolant, also known as antifreeze coolant, is a liquid with antifreeze properties. The specific replacement steps are as follows: 1. Open the front hood and inspect the connections of the radiator, hoses, and other components for any signs of leakage. 2. After confirming no leaks, open the reservoir cap or radiator cap to allow faster drainage of the coolant. 3. Locate the coolant drain port on the vehicle's radiator. Some models may not have a radiator drain port, in which case you can remove the heater hose to drain the antifreeze. If the drainage is incomplete, use a dust blower to pressurize the radiator, ensuring more complete coolant removal. 4. After draining the antifreeze, reinstall the drain plug or heater hose, then fill the radiator with clean water. 5. Start the engine and let the water circulate for 2-3 minutes before draining it again. This step helps clean dirt and rust from the cooling system. 6. After cleaning, drain all the water and reinstall the drain plug or heater hose. You can then add new antifreeze. 7. Once filled, start the engine and let it circulate for about 10 minutes. As some air is expelled from the system, the coolant level will drop. Top up the antifreeze until it reaches the maximum mark on the reservoir.
6
4
Share

How to Shift from D Gear to S Gear in an Automatic Transmission?

To shift from D gear to S gear, simply move the gear lever to the right from the D position. Switching between D and S gears is not affected by vehicle speed or road conditions, and there's no need to press the brake pedal; you can switch at any time. Here's some information about the S gear: 1. Sport Mode (SPORT) Driving Gear: Primarily enhances driving pleasure by increasing RPM and delaying gear shifts, or it can be used for short-term overtaking. 2. The transmission will automatically select a different gear ratio: This can also be simply understood as directly lowering one gear to keep the engine RPM within the maximum torque range, prioritizing power output. However, prolonged high-speed driving in this mode may increase fuel consumption.
1
3
Share

How to Choose the Right Headlight Height Adjustment?

Generally, the headlight height adjustment can be set at position 0. The specific methods for adjusting headlight height are as follows: 1. Position 0: Suitable when the front seats are occupied and the trunk is empty. 2. Position 1: Suitable when the vehicle is fully loaded with passengers and the trunk is empty. 3. Positions 2 and 3: Suitable when the vehicle is fully loaded with passengers and the trunk is fully loaded. The headlight height adjustment knob is usually located on the left side of the dashboard, next to the light control switch. Rotating the knob adjusts the height of the light beam. The higher the value, the higher the light beam, which can more easily cause glare for oncoming drivers.
19
5
Share

What to Do If You Haven't Completed the Driver's License Test Within Three Years?

After the three-year validity period for the driver's license test expires, if you haven't completed all the tests, the previously passed subjects will be invalidated, and you will need to retake the exams. The specific scenarios can be divided into the following three cases: 1. Enrolled in a driving school but didn't take any tests: In fact, only after passing the subject one test will the vehicle management office issue a learning driving permit, which then starts the three-year validity period. Therefore, the driving school should refund the full tuition fee. 2. Passed subject one but didn't complete the remaining subjects before the expiration: If some subjects have been passed but the remaining ones weren't completed within the three-year validity period, the driving school may refund part of the training fee. However, if the expiration is entirely due to the student's personal reasons, the driving school may not provide any refund. 3. Green channel for scheduling tests when the license validity is about to expire: If the learning driving permit has less than six months of validity remaining, students can switch to priority scheduling when booking tests.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.