···
Log in / Register

How to Set the Time on a Buick Excelle?

4 Answers
LaMichael
07/29/25 2:02am
To set the time on a Buick Excelle: 1. Turn on the radio and wait until the LCD display changes from frequency to time display. Then press and hold the number 4 button for more than 4 seconds; 2. Next, press the rewind button to select the hour (each press increases by one hour), then use the fast-forward button to set the minutes. The Buick Excelle is a mid-size sedan with body dimensions of 4468mm in length, 1765mm in width, and 1469mm in height. In terms of power, the Buick Excelle is equipped with a 1.3L naturally aspirated engine delivering 107 horsepower and 133 N·m of maximum torque, capable of reaching peak power at 6200 rpm.
Was this review help?
2
0
Share
NathanLee
08/12/25 12:01pm
I recently helped my neighbor set the time on his old Excelle. For older models, you usually adjust it at the instrument cluster: first locate two small buttons below the dashboard, press and hold the left one until the hour flashes, then briefly press the right button to adjust the hour; then press and hold the left button again to switch to minutes and use the right button to adjust. The newer models with central control screens are much simpler—just go to the settings menu and find the clock option. This car tends to forget the time setting, especially after a battery disconnect, so it's recommended to have the technician set the time when replacing the battery in winter. Last time, I also noticed that after adjusting the time accurately, the fuel consumption calculation became more precise, since the accuracy of the trip computer's timing affects mileage statistics.
Was this review help?
16
4
Share
Expand All
VonEverly
10/02/25 3:29am
When I drove the Buick Excelle before, setting the time was the biggest headache. You had to press and hold that small pillar-like button on the dashboard until the numbers blinked, then rotate the knob to adjust. Pay attention to AM/PM as the 12-hour format can be confusing. I usually adjusted it while refueling at gas stations since the engine idle provides stable voltage. If the button gets stuck, don't force it - use an alcohol-dipped cotton swab to clean the contacts as plastic parts age in older cars. After setting, remember to confirm synchronization via the CD player, otherwise the multimedia display and dashboard clocks won't match, which looks particularly annoying when driving at night.
Was this review help?
13
2
Share
Expand All
FernandoDella
11/15/25 5:12am
Adjusting the Excelle's time varies by model. For pre-2007 models with H/M buttons on the dashboard: After ignition, press H to adjust hours and M to adjust minutes. If buttons feel stiff, gently tap them with a fingernail before pressing. For post-2010 models, use steering wheel button combinations—enter the setup menu via left-side control buttons. Personal tip: Don't exceed 30 seconds when adjusting time, or the ECU may reset. Once, my cruise control failed after adjustment and only resumed after resetting the time. Older car circuits are sensitive—recommend operating before engine shutdown.
Was this review help?
4
1
Share
Expand All
More Forum Discussions

What to Do When the Gear Won't Come Out?

If the gear won't come out, you must go to a 4S shop or a professional auto repair shop to have professionals inspect and repair it. The reasons why the gear won't come out include: 1. At the rear of the transmission, there are two connecting rods. If the screw is loose or falls off, the gearshift lever inside the car can move, but the movement won't be transmitted to the transmission, so the gear won't come out; 2. The clutch pressure plate is damaged and cannot disengage, making it difficult to shift out of gear; 3. The gearshift cable is broken. If the gearshift cable is broken, the response of the gearshift lever cannot be transmitted to the transmission actuator. The transmission mainly refers to the car's transmission, including manual and automatic types. The manual transmission mainly consists of gears and shafts, achieving speed and torque changes through different gear combinations, while the automatic transmission (AT) is composed of a torque converter, planetary gears, a hydraulic torque variation system, and a hydraulic control system, achieving speed and torque changes through hydraulic transmission and gear combinations.
3
1
Share

What to Do If There's a Rust Hole in the Vehicle's Metal Sheet?

If there's a rust hole in the vehicle's metal sheet, the rusted area needs to be cut out and then re-welded or treated with anti-corrosion measures. The materials used for automobile bodies can generally be divided into two major categories: 1. Metal materials, including heavy metals such as steel plates and cast iron, as well as light metals like aluminum, magnesium, titanium and their alloys, and foam metals; 2. Non-metal materials, including engineering plastics, fibers, resins, glass, rubber, non-metal foam materials, and non-metal composite materials. With the advancement of automotive technology, in addition to metal and non-metal materials, composite materials and nanomaterials will also see widespread application in future automotive materials.
1
4
Share

How to Replace the Battery in an Audi Q3 Remote?

Audi Q3 remote battery replacement steps: 1. Flip the car remote key to the back side, where you can see the back cover divided into two parts. The side with the keyring is where the battery is located under the back cover; 2. Turn the key sideways to look for a gap, usually near the keyring and along the side of the key. However, the back cover cannot be removed by hand; 3. Use a flathead screwdriver to insert into the gap and apply slight upward force to lift part of the back cover. Since force is applied at one point, the entire back cover cannot be removed at once; 4. Move the screwdriver along the gap to both sides to gradually widen the gap; 5. The entire back cover can then be pried open; 6. Push the back cover towards the closed side by hand to remove it, revealing the battery inside; 7. A protruding clip can be seen on one side of the battery. Press the clip part of the battery, and the battery will expand. Slide the battery to the other side to remove it; 8. Insert the new battery into the car remote key in the reverse order of removal, paying attention to the positive and negative poles to avoid installing the battery in reverse.
7
5
Share

What transmission does the Axela use?

The Axela is equipped with the Skyactiv-Drive 6-speed automatic transmission. The Axela comes with two naturally aspirated engines featuring Skyactiv technology: a 1.5L and a 2.0L, delivering maximum power outputs of 117 horsepower and 158 horsepower respectively, with peak torques of 148 Nm and 202 Nm. The transmission system is paired with either a 6-speed manual or a 6-speed automatic transmission. For suspension, the new model adopts a front MacPherson strut independent suspension and a rear multi-link independent suspension combination. The sedan version of the Axela has body dimensions of 4582mm in length, 1795mm in width, and 1458mm in height, while the hatchback version measures 4461mm in length, 1795mm in width, and 1474mm in height. Both versions share the same wheelbase of 2700mm.
14
4
Share

What does the D in an automatic car mean?

In an automatic transmission car, D stands for Drive, which is used for forward movement on regular road surfaces and is one of the most commonly used gears. It automatically adjusts to a comfortable working state based on road conditions and vehicle speed. Nowadays, more and more cars are equipped with automatic transmissions, commonly known as automatic cars. Automatic cars typically have P, N, R, and D gears. N stands for Neutral, which functions similarly to the neutral gear in manual transmissions, used for temporary parking. Another purpose is when the engine suddenly stalls while driving; if you need to restart the engine while moving, you must shift into N gear. P stands for Park, used when the engine is off and the car is stationary or parked. When the vehicle is stopped, you must shift into P gear to power off, remove the key, and lock the doors. R stands for Reverse, which functions the same as the reverse gear in manual transmissions.
11
5
Share

Do I need to retake Subject 1 when switching from C1 to C2?

Switching from C1 to C2 does not require retaking the exam, but you need to resubmit the application form and medical examination certificate. Passing score for Subject 1: The total time for the Subject 1 exam is 45 minutes. The exam consists of 100 questions, including true/false and multiple-choice questions, with a full score of 100 and a passing score of 90. The exam papers are randomly selected and combined by the computer driver examination system according to the proportion specified in the "Motor Vehicle Driver's License Work Specifications". Exam process: Follow the staff's arrangements and collect your driving school file in order in the waiting area; Carry and present your ID card for inspection by the supervising officer; Mobile phones must be turned off when entering the exam area; No loud noise is allowed in the exam area; Regulation textbooks are not allowed in the exam area (or should be placed in your bag); After the exam, keep your ID card safe and submit the file to the "Document Submission Window" at the front of the exam area; Students who pass the exam will sign under the guidance of the staff at the exam exit and then leave the exam area; Students who fail the exam can leave the exam area immediately and wait for the driving school staff to notify them of the retake time.
6
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.