How to Set the Speed on the Volkswagen Lavida Screen?

1 Answers
AaronMarie
07/29/25 1:42pm
The method to set the speed on the Volkswagen Lavida screen is: 1. Use the trip button to navigate to the page displaying the circled km/h, then press the OK or reset button; 2. The screen will show a default speed of 30 km/h. To increase the number, press the up button on the trip key located on the wiper stalk—each press increases the speed by 5 km/h. Taking the 2021 Volkswagen Lavida as an example, it is a compact car with the following dimensions: length 4670mm, width 1806mm, height 1474mm, wheelbase 2688mm, and a trunk capacity of 510 liters. The 2021 Volkswagen Lavida features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.4T turbocharged engine, delivering a maximum horsepower of 150 PS, maximum torque of 250 Nm, and maximum power of 110 kW, paired with a 7-speed dual-clutch transmission.
Was this review help?
14
5
Share
More Forum Discussions

Is the Green Book Required for Vehicle Scrapping?

Article 27 of the "Regulations on the Registration of Motor Vehicles" stipulates that when a motor vehicle that has reached the national mandatory scrapping standard is sold by the owner to a motor vehicle recycling enterprise, the owner shall fill out an application form and submit the motor vehicle registration certificate, license plate, and vehicle license. The motor vehicle recycling enterprise shall confirm the motor vehicle and dismantle it, and issue a "Recycling Certificate for Scrapped Motor Vehicles" to the owner. Scrapped school buses, large passenger vehicles, trucks, and other commercial vehicles shall be dismantled under the supervision of the vehicle management office. The compensation standards for vehicles totaled in traffic accidents are as follows: 1. First category: When the repair cost of the vehicle exceeds 80% or more of the vehicle's value, the insurance company will settle the claim as a vehicle scrapping insurance. 2. Second category: The vehicle meets the mandatory scrapping standards. According to Article 4 of the "Mandatory Scrapping Standards for Motor Vehicles," registered motor vehicles shall be mandatorily scrapped under the following circumstances: First: After repair and adjustment, they still fail to meet the national safety technical standards for in-use motor vehicles; Second: After repair, adjustment, or the use of control technology, the emission of pollutants or noise into the atmosphere still fails to meet national standards for in-use motor vehicles.
13
4
Share

How Long Can the Air in a Car Sustain a Person?

How Long Can the Air in a Car Sustain a Person? The air in a car can sustain a person for about 10 hours. Below are some relevant points about resting in a car: 1. Parking with the Air Conditioning On: Another major hazard of resting in a car is parking with the air conditioning on, which may lead to carbon monoxide poisoning. However, pure electric vehicles do not have this concern, as this mainly applies to fuel-powered vehicles. Running the air conditioning requires the engine to be on, and burning fuel produces a certain amount of carbon monoxide. Long-term idling of the vehicle can emit large amounts of carbon monoxide. Additionally, with poor air circulation around the car, even if the windows and doors are tightly closed, carbon monoxide can enter the car through the external air conditioning circulation. Accumulation to a certain level can cause poisoning. 2. Precautions: The interior of a car is essentially a sealed environment. If you plan to sleep in the car, it is recommended to leave the windows slightly open as a precaution. This is especially important for those who prefer to park with the air conditioning on—always park in an open area and ensure the windows are not completely closed.
9
2
Share

What are the reasons for the Buick Excelle's air conditioning not cooling?

Buick Excelle's air conditioning not cooling reasons include refrigerant leakage, internal damage to the air conditioning pump, compressor damage, and excessively dirty condenser fins. Below are detailed explanations: Refrigerant Leakage: If the refrigerant in the air conditioning system leaks completely, there will be no refrigerant left, causing the air conditioning not to cool. Solution: Check for leaking components, add refrigerant along with fluorescent dye. Internal Damage to the Air Conditioning Pump: This results in the inability to initiate the cooling effect, and generally, a damaged air conditioning pump will produce abnormal noises. Solution: Inspect the air conditioning pump and replace it. Compressor Damage: When the compressor is damaged, it stops working or the pressure difference in the high and low-pressure pipelines becomes very small. This situation will cause the air conditioning not to cool. Solution: Check the compressor and replace it. Excessively Dirty Condenser Fins: This leads to excessively high pressure and temperature in the air conditioning system. To protect the system, the air conditioning pump stops working, resulting in the air conditioning not cooling. Solution: Use a high-pressure water gun to clean the condenser fins, then dry them with a high-pressure air gun.
10
1
Share

How to Use Electronic Parking Brake Correctly?

Using the electronic parking brake is relatively simple, typically achieved by pressing the electronic parking button inside the vehicle. After parking and turning off the engine, the driver can directly press the electronic parking button. The Electronic Parking Brake (EPB) integrates temporary braking during driving with long-term braking after parking, and employs electronic control to achieve parking braking. Below is an introduction to the electronic parking brake: 1. The working principle of the electronic parking brake is the same as that of a mechanical handbrake, both of which tighten the rear brake shoes via cables to achieve braking. Another type uses an electromechanical caliper, where the motor clamps the brake to control parking braking, extending the basic parking function to the automatic parking function AUTO-HOLD. 2. Currently, there are two types of electronic parking brake switches on the market: one is a standard button type, where pressing once activates the electronic parking brake, and pressing again deactivates it; the other is a toggle switch type, similar to a window control switch, where pushing up activates the parking brake function, and pushing down deactivates it.
9
1
Share

Where is the Jetta trunk switch located?

You need to gently lift the trunk button to open it. Additionally, you can also use the key to turn the switch. Many models allow you to unlock the trunk directly by pressing the trunk unlock button on the key. If the key is within the sensing range, you can directly pull the trunk handle and lift the trunk lid. Some models also have two additional buttons on the trunk: the left button is for closing the trunk, and the right button is for closing the trunk and locking the car.
19
4
Share

Where is the Buick LaCrosse cabin air filter located?

Buick LaCrosse cabin air filter is located behind the glove box on the passenger side. Here are the steps to locate the cabin air filter: 1. Open the glove box cover, push the lever to the right and remove it. 2. Remove the glove box to reveal the cabin air filter housing cover. 3. Open the cabin air filter cover to access the filter. The functions of the cabin air filter include: 1. Absorbing dust particles. 2. Reducing respiratory discomfort for drivers. 3. Minimizing irritation for allergy sufferers. 4. Protecting the air conditioning cooling system. Below is the replacement method for Buick LaCrosse cabin air filter: 1. Remove the passenger side glove box. Open the glove box, disconnect the damper, squeeze the side walls inward to release the limit clips, allowing the glove box to tilt downward. Alternatively, loosen the upper and lower fixing screws to remove the entire glove box. Note to unplug the glove box lighting connector. 2. Remove the cabin air filter cover. The elongated cover has clips on both sides - squeeze them toward the center to release. 3. Take out the old filter and install the new one. Pay attention to the orientation - the arrow mark on the new filter should face upward. 4. Reinstall the filter cover and reassemble the glove box in reverse order.
14
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.