How to set the power mode to ON for the Haval H6 third generation?

2 Answers
Deanna
07/29/25 6:10am
To set the power mode to ON for the Haval H6 third generation, press the one-touch start button once when the gear lever is in the P position. Below is an introduction to the Haval H6: 1. Design Evolution: After three generations of glorious evolution, the third-generation Haval H6 boasts a powerful presence; its Eastern-style futuristic aesthetic design language highlights strong dynamic lines, while the interior features a super-sensory future smart cockpit design. 2. Intelligent Evolution: With over a thousand intelligent upgrades, it integrates cutting-edge smart technologies, including full-vehicle FOTA upgrades and supports beyond L2-level autonomous driving. It also features 22 intelligent driving assistance functions such as full-scenario AEB automatic emergency braking, 50-meter fully automatic tracking reverse, and smart evasion.
Was this review help?
11
5
Share
LeilaniRose
08/12/25 9:39am
Turning on the ON mode for the 3rd-gen H6's power supply is quite simple. First, I make sure the smart key is inside the vehicle. Then, without pressing the brake pedal, I press the start button on the center console once—this puts the car into ACC mode, where the air conditioning and audio system are operational but the dashboard isn't fully lit. Pressing the button once more switches it to ON mode, powering all electronic systems and illuminating the dashboard without starting the engine. I sometimes do this to listen to the radio or charge devices, avoiding unnecessary battery drain. The whole process takes just seconds, with dashboard indicator changes confirming the current mode. Remember not to press the button too quickly while keeping your foot off the brake, as this could directly start the engine. As an enthusiast who closely follows automotive technology, I appreciate this staged power supply design for protecting battery life. I also regularly check the smart key's battery health to prevent malfunctions, ensuring safe, convenient, and worry-free operation.
Was this review help?
4
0
Share
Expand All
More Forum Discussions

What Octane Gasoline Should a Normal Car Use?

The selection of gasoline octane rating should be determined by the compression ratio of the car's engine. The appropriate fuel octane rating for the vehicle is usually indicated on the inside of the fuel tank cap. If it specifies 92-octane fuel, then use 92-octane. If it specifies 95-octane fuel, then use 95-octane. Whether the gasoline is 92 or 95 octane, the number represents the fuel's anti-knock performance. A higher octane rating indicates better anti-knock performance, but it does not necessarily mean higher fuel quality, contrary to the common belief that higher octane fuel is always better. For naturally aspirated engines, 92-octane gasoline is generally recommended. Higher-octane fuel has better anti-knock performance but burns relatively slower, which can lead to higher compression ratios in the engine, resulting in reduced power and increased temperatures. For turbocharged engines, manufacturers typically recommend 92-octane or higher. Using 95-octane gasoline not only ensures higher torque at low speeds but also helps reduce engine vibration and noise.
12
0
Share

How to Turn Off the Auto Start-Stop Function in the Honda Avancier?

The auto start-stop function of the Honda Avancier is set via a mechanical button located on the left side of the driver's seat. To deactivate it, simply press the button. Below are some usage tips for the Honda Avancier's auto start-stop feature: 1. The auto start-stop function can only be manually turned off each time. 2. It is recommended to disable the start-stop function during frequent traffic congestion. 3. Additionally, this function should be turned off when starting on a slope. Possible reasons why the Honda Avancier's auto start-stop may not work: 1. The start-stop function is activated only when the battery charge exceeds 60%. 2. The temperature inside or outside the vehicle is too low. 3. The engine has not reached the standard operating temperature. 4. The steering wheel angle deviates more than 30 degrees from the central axis.
12
1
Share

How to Fold Down the Rear Seats of Baojun 530?

Method to fold down the rear seats of Baojun 530: 1. There is a buckle in the middle position under the rear seat cushion. Lift it forcefully to fold the cushion forward. There is a pull strap below the backrest; pulling it allows you to adjust or fold down the backrest. 2. The Baojun 530 is a compact SUV. Its front features a hexagonal grille with dual chrome slats, and the headlights on both sides adopt a split-type design. 3. The rear seats of the Baojun 530 can be folded down as a whole. This means the backrest of the rear seats is a single unit. When transporting large items and needing more space, you can fold down the rear seat backrest to gain additional room, making it highly suitable for family use.
3
2
Share

How many kilometers can you drive when the tire wears to the safety line?

Tires should not be driven when they wear to the safety line because at this point, the tire's drainage and grip are very poor, which may lead to loss of control or skidding during driving. It is necessary to replace the tire promptly. The safety line is usually located at the bottom of the tire grooves as a wear indicator. Its purpose is to remind the owner that if the tire tread wears down to this position, the tire must be replaced. The following are precautions for car tire maintenance: Pay attention to tire pressure: Tire pressure is crucial for tires. Both overinflation and underinflation can shorten the tire's lifespan. Underinflation increases tire deformation, leading to cracks on the sidewalls and excessive flexing, which generates heat and accelerates rubber aging, fatigue of the cord layers, and cord breakage. Regularly check front-wheel alignment: Front-wheel alignment significantly affects tire lifespan, with toe-in and camber being the primary factors. Excessive camber mainly accelerates shoulder wear, while incorrect toe-in (too small or too large) primarily accelerates wear on the inner or outer edges of the tire. Be mindful of driving habits: Choose smooth roads while driving to avoid sharp objects like stones, glass, or metal that may puncture or damage the tires. Avoid chemical spills that could adhere to or corrode the tires. When driving on roads with significant curvature, try to stay centered to reduce uneven tire wear caused by increased load on one side.
8
0
Share

What to Do About High Fuel Consumption in Nissan Sylphy?

Sylphy high fuel consumption solutions are as follows: 1. Regularly clean the air filter to ensure the engine breathes fresh air and maintains smooth air intake. 2. Periodically inspect and replace spark plugs in the ignition system, as sufficiently strong ignition sparks are essential for complete combustion of the fuel-air mixture. 3. The fuel system should also be cleaned regularly, as carbon buildup on the fuel injectors can cause needle valve sealing issues, leading to fuel leakage. 4. The engine interior should be periodically cleaned of carbon deposits, as excessive carbon buildup can cause inaccurate fuel control, thereby increasing fuel consumption.
16
5
Share

Where is Audi produced?

Audi's production site is at the company headquarters: Ingolstadt, an industrial city in Bavaria, Germany, located on the banks of the Danube. Audi also has production plants in China (Changchun), Malaysia, South Africa, and other locations. Below is a detailed introduction about Audi: 1. The Audi Group includes the parent company and its subsidiaries, Audi Hungaria, quattro GmbH, as well as Lamborghini Automobili and Coworth Technology, Audi Brazil, and Audi Senna. 2. In 1969, Auto Union GmbH and NSU GmbH were renamed Audi-NSU Auto Union AG, and in 1985, it was officially renamed Audi AG. Currently, Audi AG has become a subsidiary of Volkswagen AG.
1
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.