How to Set Nighttime Charging Time for Tesla?

Is the Tayron equipped with a dry or wet dual-clutch transmission?

The 1.4-liter version of the Tayron uses a dry dual-clutch transmission, while the 2.0-liter version is equipped with a wet dual-clutch transmission. Detailed information about dual-clutch transmissions is as follows: 1. In a dry dual-clutch transmission, the clutch connects the driving plate and the driven plate through air, directly contacting the engine flywheel. 2. A wet dual-clutch transmission uses oil to connect the driving plate and the driven plate, immersing the clutch plates in a sealed oil trough to absorb the heat they generate, significantly improving heat dissipation performance. This results in better performance in terms of shifting speed, fuel consumption, and comfort. 3. A dual-clutch transmission (DCT) has two sets of clutches in the transmission system, each connected to an input shaft—one controlling the odd-numbered gears and the other the even-numbered gears. This greatly reduces shifting time and increases efficiency, enhancing comfort during gear changes.

9

5

Share

What Causes the Motorcycle Engine Oil Light to Illuminate?

Analysis and solutions for the motorcycle engine oil light illumination: 1. Insufficient engine oil level, leading to inadequate lubrication and low oil pressure. Solution: Top up oil. 2. Dirty or thickened oil preventing the oil pump from effectively circulating oil, causing low or no oil pressure. Solution: Change oil. 3. Thin oil or thinning due to high engine temperature, resulting in leakage through engine gaps and low oil pressure. Solution: Change oil or inspect cooling system. 4. Oil pipe leakage or oil pump damage/excessive wear reducing oil circulation, leading to low or no oil pressure. Solution: Inspect and repair. 5. Excessive clearance between crankshaft and bearings causing oil leakage and low pressure. Solution: Repair. 6. Faulty pressure relief valve due to weak/ stuck spring or damaged ball, reducing oil pressure. Solution: Replace or repair. 7. Oil sensor, pressure gauge, or electrical circuit malfunction causing low oil pressure. Solution: Replace or inspect.

11

3

Share

What are the battery specifications of the Baojun 730?

The Baojun 730 uses a Camel brand 86550T-12V-55Ah-550CCA battery. The car battery is installed in an appropriate location with special safety features. If the battery must be replaced, ensure the new battery's electromagnetic compatibility, dimensions, maintenance, output power, and safety requirements are considered before purchase. Here are the relevant details: 1. Checking the electrolyte level of a battery with an inspection eye: (1) To clearly identify the color inside the circular window on the battery, ensure sufficient lighting. Never use an open flame or sparking items for illumination. (2) The circular window on the upper part of the car battery changes color based on the electrolyte level. 2. Checking the electrolyte level of a battery without an inspection eye: (1) The electrolyte level should always be between the "Min" and "Max" marks on the side of the battery and should never exceed the "Max" mark. (2) If the electrolyte level is below or near the "Min" mark, the battery should be replaced immediately.

18

5

Share

How to Confirm ETC is Functioning Properly?

Methods to check if ETC is functioning properly: Manually insert and remove the card once. If there is a sound, it indicates that the ETC is in normal working condition. ETC working principle: Through the dedicated short-range communication between the on-board electronic tag installed on the vehicle's windshield and the microwave antenna on the ETC lane of the toll station, computer networking technology is used to conduct background settlement processing with the bank, thereby achieving the purpose of vehicles passing through highway or bridge toll stations without stopping while being able to pay highway or bridge fees. Where can ETC be installed: For small vehicles such as cars and minivans, the OBU device is installed in the upper middle part of the front windshield, while for large vehicles such as trucks and buses, the installation position is in the middle and lower part. ETC installation position requirements: The height should not be less than 1.2 meters or higher than 2.5 meters; the installation angle N should be between 30º and 90º (the angle between the surface of the electronic tag and the horizontal plane).

5

4

Share

How to reset the maintenance light on the 2016 Great Wall H6?

There are two versions of the Great Wall H6: the Red Label and the Blue Label. Below are the methods to reset the maintenance light for both versions: 1. For the Great Wall Red Label Haval H6, follow these steps to reset the maintenance light: 1. Insert the key and keep the engine off. 2. Press the reset button once to display the system that needs to be reset. Each press will switch to the next system. 3. Select the system you want to reset and hold the reset button for about 3 seconds. 4. The multifunction display on the dashboard will show the relevant icon, indicating the maintenance light has been successfully reset. 2. For the Great Wall Blue Label Haval H6, follow these steps to reset the maintenance light: 1. Turn on the ignition without starting the engine. 2. Press the reset button once to switch and select the system you need to adjust. 3. Turn the ignition to the second position and hold the reset button for about 3 seconds. 4. The multifunction display on the dashboard will show the relevant icon, indicating the maintenance light reset is complete.

5

3

Share

What are the reasons for an automatic transmission not engaging?

An automatic transmission not engaging may be due to a malfunction in the gearshift lever assembly, a failure in the P-gear lock solenoid valve inside the gearshift lever, or a damaged brake light switch, which can also prevent the gear from moving. Related explanations are as follows: 1. During the use of the car's gearshift lever, shifting gears requires looking down at the lever. Driving for long periods in low gear is not recommended, as high gears are more fuel-efficient than low gears, so it is advisable to shift up promptly after starting. If the clutch is not fully depressed when shifting, it can cause gear damage. Additionally, when not using the clutch, the foot should not rest on it, as this can lead to excessive wear on the release bearing. 2. If a gear does not engage on the first attempt, avoid forcing it. When the gearshift lever is in neutral, it should not be shaken back and forth, as this can cause unnecessary wear on components and affect the timing of gear shifts. Skipping gears when upshifting is not recommended; upshifting should be done step by step to ensure continuous power delivery, while downshifting can skip gears. Avoid engaging reverse gear before the vehicle has come to a complete stop, as this can damage the gears.

8

2

Share

How to Set Nighttime Charging Time for Tesla?

Is the Tayron equipped with a dry or wet dual-clutch transmission?

What Causes the Motorcycle Engine Oil Light to Illuminate?

What are the battery specifications of the Baojun 730?

How to Confirm ETC is Functioning Properly?

How to reset the maintenance light on the 2016 Great Wall H6?

What are the reasons for an automatic transmission not engaging?

What Causes Severe Engine Shaking During Cold Start?

Where to Check the Production Date of a Newly Purchased Car?

What is the maximum age for driving with a C1 driver's license?

What Are the Causes of BMW Transmission Abnormal Warning?