How to Set Cruise Control on Volkswagen Magotan?

Can a Car Pass Annual Inspection with a Small Spoiler Installed?

Small cars with installed spoilers cannot pass the annual inspection. Below is the relevant introduction to the annual inspection: 1. Required documents for personal vehicles: (1) Original vehicle license; (2) Copy of compulsory traffic insurance; (3) Copy of ID card; (4) The vehicle. 2. Required documents for company vehicles: (1) Original vehicle license; (2) Copy of compulsory traffic insurance; (3) Organization code certificate of the People's Republic of China (with fresh seal); (4) Power of attorney (with fresh seal) and copy of the agent's ID card. 3. Inspection models: Small and micro passenger vehicles within six years are exempt from inspection. Moreover, small and micro passenger vehicles over six years but less than 10 years will have their inspection frequency adjusted from once a year to once every two years.

15

5

Share

What to Do If a Car Designed for 92 Octane Fuel Accidentally Uses 95 Octane?

Using 95 octane fuel in a car designed for 92 octane actually has minimal negative impact. The primary reason is that higher-octane fuel has a greater octane rating than lower-octane fuel, leading to more complete combustion. As a result, the vehicle may exhibit improved performance in terms of power output. Below are some additional details: When higher-octane fuel is mistakenly replaced with lower-octane fuel, the following situations may occur: 1. The vehicle may experience insufficient power and increased fuel consumption: Some vehicles' engine warning lights may activate, and in severe cases, the engine may stall or fail to start. 2. If there is a significant difference between the octane ratings of the mistakenly added fuel: The owner should promptly drain the fuel from the tank and thoroughly clean the fuel tank and fuel system to minimize potential damage to the engine caused by lower-quality fuel.

6

3

Share

What is the National Testing Standard for China VI Diesel?

The national testing standards for China VI diesel mainly include: 1. A 50% reduction in carbon monoxide emissions from gasoline vehicles. 2. A 50% decrease in the emission limits for total hydrocarbons and non-methane hydrocarbons. 3. A 42% stricter nitrogen oxide emission limit. Here are some additional details: 1. Introduction: The China VI vehicle pollutant emission standards were established to implement the "Environmental Protection Law of the People's Republic of China" and the "Air Pollution Prevention and Control Law of the People's Republic of China," aiming to prevent pollution from the exhaust of compression-ignition and gas-fueled ignition engine vehicles, protect the ecological environment, and safeguard human health. 2. Coverage: The standards consist of two parts: "Limits and Measurement Methods for Emissions from Light-Duty Vehicles (China VI)" and "Limits and Measurement Methods for Emissions from Heavy-Duty Diesel Vehicles (China VI)."

18

0

Share

How to Deal with Scratches on Car Bumpers?

Minor scratches on the bumper can be polished with coarse wax. Below is a detailed introduction about car bumpers: 1. Overview: Car bumpers are safety devices designed to absorb and mitigate external impacts, protecting the front and rear parts of the vehicle body. With the development of the automotive industry and the extensive application of engineering plastics, car bumpers, as an important safety device, have gradually evolved. In addition to maintaining their original protective functions, the front and rear bumpers of cars also pursue harmony and unity with the vehicle's styling and aim for lightweight construction. 2. Composition: The front and rear bumpers of cars are made of plastic, commonly referred to as plastic bumpers. Generally, a car's plastic bumper consists of three parts: the outer panel, the cushioning material, and the crossbeam. The outer panel and cushioning material are made of plastic, while the crossbeam is formed by stamping cold-rolled thin sheets into a U-shaped channel. The outer panel and cushioning material are attached to the crossbeam.

20

4

Share

What are the components and functions of the crank-connecting rod mechanism?

The function of the crank-connecting rod mechanism is to provide a combustion chamber, convert the expansion pressure of the gas acting on the top of the piston after fuel combustion into the rotational torque of the crankshaft, and continuously output power. The following are the components of the crank-connecting rod mechanism: 1. Engine block group: cylinder block, cylinder gasket, cylinder head, crankcase, cylinder liner, and oil pan; 2. Piston-connecting rod group: piston, piston ring, piston pin, connecting rod; 3. Crankshaft-flywheel group: crankshaft, flywheel, torsional vibration damper, balance shaft. The following are its functions: 1. Convert gas pressure into crankshaft torque; 2. Convert the reciprocating motion of the piston into the rotational motion of the crankshaft; 3. Convert the force of combustion acting on the top of the piston into crankshaft torque to output mechanical energy to the working machinery.

19

4

Share

What is the symbol for the auto-hold function?

The auto start-stop button symbol is a circle with an 'A' inside and the letters 'OFF' below it. Auto start-stop switch: The auto start-stop function is enabled by default. To turn off the engine's auto start-stop function, press the auto start-stop button. However, it will be enabled by default again when the car is started next time. Engine start-stop technology: Engine start-stop is a relatively advanced technology, a system that can automatically control engine shutdown and ignition. When the engine is in a brief dormant state, it achieves the purpose of energy saving and emission reduction, and is suitable for urban traffic. Automatic control: The auto start-stop function allows the car to automatically shut down when needed and automatically restart the engine when the car needs to move forward. The auto start-stop function is achieved by implanting an idle start-stop motor in the car engine. When the car meets the idle condition, the engine automatically shuts down and stops working. When the car needs to move forward, the motor system quickly starts the engine, reducing the car's fuel consumption and exhaust emissions, and improving the car's fuel economy.

16

2

Share

How to Set Cruise Control on Volkswagen Magotan?

Can a Car Pass Annual Inspection with a Small Spoiler Installed?

What to Do If a Car Designed for 92 Octane Fuel Accidentally Uses 95 Octane?

What is the National Testing Standard for China VI Diesel?

How to Deal with Scratches on Car Bumpers?

What are the components and functions of the crank-connecting rod mechanism?

What is the symbol for the auto-hold function?

What Causes Fogging on the Outside of the Windshield When Using Air Conditioning?

How to Obtain a New Energy Vehicle Quota in Beijing?

What is the penalty for honking in a no-honking zone?

What to Do When the Car Won't Start After Sitting for a Long Time?