How to Return a Yong'anxing Bike When There Are No Available Docks?

What are the symptoms of a faulty plain bearing?

When a plain bearing is faulty, the following symptoms may occur: 1. A "click-click-click" noise when turning the steering wheel. 2. A "thud-thud-thud" sound when turning the steering wheel while stationary or at low speeds. 3. Vibration in the steering wheel, increased steering effort, and noticeably louder tire noise while driving. In severe cases, a "humming" sound may be heard. 4. Noise when passing over speed bumps, vehicle pulling to one side, damage to the steering system, and damage to the suspension system. 5. Poor quality bearing materials and insufficient surface treatment hardness. The first part to fail is the area marked in the red circle, as it is the weakest point.

6

2

Share

How to activate cruise control on the Leiling?

To activate cruise control on the Leiling, follow these steps: when the vehicle speed reaches above 40 km/h, turn on the cruise control switch, then press the deceleration button. Taking the 2021 Leiling as an example, it belongs to the compact car category with the following dimensions: length 4640mm, width 1780mm, height 1455mm, wheelbase 2700mm, fuel tank capacity 43L, and curb weight 1410kg. The 2021 Leiling features a MacPherson strut front suspension and an E-type multi-link rear suspension. It is equipped with a 1.8L naturally aspirated engine, delivering a maximum horsepower of 98PS, maximum power of 72kW, maximum torque of 142Nm, paired with an electronic continuously variable transmission.

2

1

Share

What are Plug-in Hybrid Electric Vehicles?

Plug-in hybrid electric vehicles include: BMW 7 Series Plug-in Hybrid, Mercedes-Benz C350eL, Audi A3 Sportback e-tron, Golf GTE Plug-in Hybrid, and other plug-in hybrid versions. Below is extended information about plug-in hybrid electric vehicles: 1. The BMW 7 Series Plug-in Hybrid is equipped with a powertrain consisting of a 2.0T engine and an electric motor, with a maximum output power of 313 horsepower (230 kW). 2. The Mercedes-Benz C350eL Plug-in Hybrid model features a hybrid system composed of a 2.0T engine and an electric motor, paired with a newly upgraded 7-speed automatic transmission. It delivers a maximum power of 155 kW and a peak torque of 350 N·m. 3. The Audi A3 Sportback e-tron is equipped with a plug-in hybrid system consisting of a 1.4TFSI engine and an electric motor, achieving a maximum power of 204 horsepower and a peak torque of 350 N·m. 4. The Golf GTE Plug-in Hybrid system combines a 1.4TSI engine with an electric motor, delivering a maximum power output of 204 horsepower and a maximum torque of 350 N·m. For transmission, it is paired with a 6-speed DSG gearbox.

4

0

Share

What is the emission standard for 2008 vehicles?

2008 vehicles comply with either China III or China IV emission standards. Methods to check a vehicle's emission standard include: 1. Inspecting the vehicle's environmental protection label; 2. Querying on the website of the Motor Vehicle Exhaust Pollution Supervision and Management Center; 3. Checking the vehicle's factory-issued compliance certificate; 4. Roughly estimating based on the vehicle's registration year; 5. Visiting the vehicle management office with the original or copy of the motor vehicle registration certificate. Major automotive emission pollutants include hydrocarbons, nitrogen oxides, carbon monoxide, and particulate matter. Through technologies such as improved catalytic converter active layers, secondary air injection, and exhaust gas recirculation systems with cooling devices, these pollutants are controlled and reduced to meet specified standards.

13

4

Share

How to Replace the Seat Belt Socket of Lynk & Co 01?

Lynk & Co 01 seat belt socket replacement steps are as follows: 1. Remove the seat belt cover and lower fixing bolt. 2. Remove the upper pillar trim panel. 3. Remove the seat belt cover, fixing bolt and lower pillar trim panel. 4. Remove the seat belt retractor fixing bolt. 5. Remove the height adjuster fixing bolt. 6. Take out the new seat belt and reverse the above steps to install it. The seat belt needs to be replaced under the following circumstances: 1. When the internal retractor of the seat belt ages, causing the seat belt to be too loose or unable to tighten in time, the seat belt should be replaced immediately. 2. If the seat belt has been subjected to strong tensile loads during use, it should be replaced in time for safety reasons, even if it is not damaged yet, and should no longer be used. 3. If the vehicle is involved in a collision that causes the airbag to deploy or explode, the seat belt must be replaced at the same time.

3

5

Share

What is the structure of the steering system?

The structure of the steering system consists of: the control mechanism, the steering gear, and the steering linkage, which are a series of devices used to change or maintain the direction of the car's movement or reverse. The causes of steering system failures include: 1. Abnormal noise when turning; 2. Steering gear oil leakage; 3. Difficulty in returning to the original position; 4. Power steering pump oil leakage; 5. Heavy steering. The solutions for steering system failures are: 1. Inspect the steering gear, steering pump control valve, oil cup filter, and steering oil, and clean the entire power steering system; 2. Check the tire pressure and replenish it in time if low; 3. Inspect all connection points of the oil pipes and tighten all connection bolts; 4. Replace the oil pipes, power steering pump, or power steering gear.

18

0

Share

How to Return a Yong'anxing Bike When There Are No Available Docks?

What are the symptoms of a faulty plain bearing?

How to activate cruise control on the Leiling?

What are Plug-in Hybrid Electric Vehicles?

What is the emission standard for 2008 vehicles?

How to Replace the Seat Belt Socket of Lynk & Co 01?

What is the structure of the steering system?

What is the reason for not being able to start the car with a jump start?

What kind of engine oil is best for FAW-Volkswagen Sagitar?

What are the reasons for car shaking after starting?

Is it normal for the side of a tire to feel indented?