How to Retrieve a Card Dropped Inside the Car Door?

2 Answers
DelLila
07/24/25 12:38pm
If a card falls inside the car door, removing the door panel is necessary to retrieve it. It's common to see people inserting small cards into the gap between the door and the window glass. Before lowering the window, car owners must remove the card; otherwise, it can easily fall into the door. If a card gets stuck between the door and the window glass, it can cause scratches on the glass surface and lead to issues like slower window operation or even jamming. Car doors have drainage holes, and if a card blocks these holes, it can cause more serious malfunctions. Therefore, if a card falls into the door, the interior panel should be removed immediately to retrieve it. During regular car use, if any foreign objects fall into the door, they should be promptly removed to prevent clogging the drainage holes, which can cause further problems.
Was this review help?
6
1
Share
DelTaylor
08/11/25 6:42am
I've encountered a situation where a card fell into the car door, and it felt quite troublesome, but don't panic. As someone who's loved cars for years, here's how I handled it: First, stay calm and avoid moving around too much. Use a flashlight to look through the door gap to locate the card. If you can see it, try using a strong magnet or tape to slowly pull it out – magnets work for metal cards, while tape is better for other materials. If that doesn't work, try using a vacuum cleaner with the nozzle aimed at the gap; sometimes that does the trick. Whatever you do, avoid using hard objects to pry it out, as this can easily scratch the door paint or damage internal wiring – I almost ruined something that way. If all else fails, it's best to contact a professional auto repair shop. They have endoscopic tools to retrieve the card precisely, which is safer and more convenient. Finally, develop good habits: store your cards securely while driving, avoiding places where they might fall, to prevent this from happening again.
Was this review help?
14
4
Share
Expand All
More Forum Discussions

What is the Minimum Speed Limit Sign?

The minimum speed limit sign indicates the minimum speed restriction for motor vehicles entering the road ahead. This sign is placed at the starting point of expressways or other speed-limited road sections. It specifies that under good road conditions ahead, motor vehicles must maintain a minimum speed of no less than 50 km/h. The sign is installed at appropriate locations including the starting points of expressways or other speed-limited road sections and after various interchange intersections. Below are detailed explanations about the minimum speed limit sign: 1. Meaning: Road traffic signs are facilities that convey specific information through graphic symbols, colors, and text to manage traffic. They play a crucial role in ensuring smooth traffic flow and driving safety, thus must be observed by all drivers and traffic participants. Traffic safety slogans can enhance drivers' and traffic participants' awareness of voluntarily complying with traffic regulations, which is significant for building a safe and smooth traffic environment. 2. Current Situation: In China, speed limit signs are primarily set based on segmented road sections. For general road sections with good alignment, speed limits are determined according to operating speeds; while for other sections, they are set based on traffic conditions or road accident statistics.
7
3
Share

What is the wading standard for the Regal?

The Regal's exhaust pipe has a ground clearance of 30.5 cm, and the half-height of its wheels is 32.5 cm. The half-height of the wheels is a conservative safe wading depth. At this water level, there is a possibility of water entering the exhaust pipe, but it won't cause the engine to stall, so you can safely pass through. Below is relevant information: Wading driving: Always drive at a low speed. For manual transmission vehicles, depending on the water depth, it is recommended to use second or third gear. In cases of deep water and heavy traffic, use first gear. Wading limit: The vehicle's air intake is located behind the grille, with the opening facing forward. The air filter is positioned about 5 cm above the air intake, so even if some water enters the intake, it won't reach the air filter. The Regal's air intake has a ground clearance of 61 cm, which is its wading limit. This is roughly equivalent to five-sixths of the wheel height, or the top of the wheel hub. When the water level reaches this point, although there is still about 5 cm to the air filter, it already prevents the engine from breathing normally. Therefore, when the water level reaches the upper seam between the wheel hub and tire, you should not continue wading.
20
0
Share

What suspension does the Volvo S80L use?

Volvo S80L uses MacPherson independent suspension for the front suspension and multi-link independent suspension for the rear suspension. The MacPherson suspension has only one L-shaped control arm, which does not occupy engine compartment space; the multi-link independent suspension is an improvement based on the double-wishbone suspension, replacing the two wishbones of the double-wishbone suspension with separate links. MacPherson suspension is an independent suspension, meaning there is no connection between the two wheels on the same axle, thus eliminating any motion interference. Multi-link suspension can improve the tire's ground contact performance, enhancing grip and thereby improving the vehicle's handling.
8
4
Share

Reasons for Car AC Not Cooling at Low Speeds

Car AC not cooling at low speeds is caused by insufficient pressure. Reason 1: Insufficient Freon: When the car is idling, especially when stopping at traffic lights or in traffic jams (lacking the cooling effect from driving wind speed), the low engine speed causes the compressor speed to also decrease. With insufficient Freon, its instant pressurization cannot reach the standard state, resulting in excessively low high pressure and suboptimal cooling performance. This can be resolved by adding some Freon, but it is important to use high-purity, environmentally friendly Freon. Reason 2: Compressor Pressure Leakage: This directly leads to severely low pressure at idle speed. In this case, the compressor needs to be replaced, which can be a significant expense. Reason 3: AC Cooling Fan Not Working: When the car is stationary, poor heat dissipation (lacking the cooling wind speed from driving) causes the pressure to become excessively high. The high-pressure sensor then forces the compressor to stop working, resulting in no cold air. In this situation, check the fuse, relay, and the fan itself to identify the faulty component and replace it. Reason 4: Expansion Valve Orifice Too Large: At idle speed, the low pressure becomes too high, significantly reducing the AC's cooling effect. This requires replacing the expansion valve and completely refilling the system with Freon.
1
3
Share

How to Identify a Car Engine Model?

Here is a detailed introduction to engine models: 1. Generally includes: number of cylinders, bore diameter, inline or V-shaped arrangement. Front part: Product series symbol and generation indicator symbol, represented by letters chosen by the manufacturer as needed, but must be approved by the relevant authority. 2. Middle part: Composed of symbols for the number of cylinders, stroke, cylinder arrangement, and bore diameter. 3. Rear part: Structural and usage characteristic symbols, represented by letters. 4. Tail part: Distinguishing symbols. L4 = Inline 4-cylinder. V6 = V-type 6-cylinder (3 cylinders per side in one row, arranged in two rows in a V shape). V8 = V-type 8-cylinder (4 cylinders per side in one row, arranged in two rows in a V shape). W12 = W-type 12-cylinder (4 cylinders per group in one row, arranged in four rows in a W shape; generally used in sports cars). For example, the 4102 engine indicates 4 cylinders in line with a bore diameter of 102 mm. 5. Usually, the manufacturer's self-assigned code is added at the front, and a Q or other letter is added at the end to indicate whether it is for automotive, marine, power generation, etc.
11
2
Share

How to Fix a Continuously Running Self-Priming Pump?

It is likely that there is air leakage in the water valve of the pressure well. The best solution is to install a separate pipe for the self-priming pump into the well. If this is not feasible, install a valve at the bottom of the pressure water device and close it when the device is not in use. This prevents air from entering the pipeline, allowing the self-priming pump to function properly. Solutions for self-priming pump motor malfunctions: 1. Pump does not work after power is connected: This could be due to issues with the power plug or wiring, such as insufficient power or a short circuit. 2. Difficult to start or noise during startup: During inspection, gently move the fan blade with a small bamboo stick. If the motor runs normally, the starting winding may be damaged. Replace the capacitor with one of the same capacity or repair the starting winding. If the motor is stuck, it may be due to faults in the motor or pump head, such as bearing damage or impeller blockage. 3. Motor runs but at a slow speed, with overheating and a burning smell: This could be caused by a motor short circuit. Open the motor to assess the damage and repair accordingly. 4. Excessive noise and vibration during operation: This is often due to bearing damage or improper fit between the bearing and the motor casing. Disassemble the motor for inspection. If the bearing is damaged, replace it. If the bearing "runs outer circle," notch the pump casing's fitting surface. If the bearing "runs inner circle," notch the worn part of the motor shaft. For severe wear, use welding followed by turning to repair.
3
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.