How to Restore a Frozen Boyue Infotainment Screen?

1 Answers
DiOmar
07/29/25 7:07pm
If the screen frequently freezes, it is recommended to upgrade the system to resolve the issue. Below is some relevant information: 1. The Boyue is a compact SUV under the Geely brand, which has gained popularity among young consumers since its launch. 2. The Boyue is equipped with three types of engines: a 1.5-liter turbocharged engine, a 1.8-liter turbocharged engine, and a 2.0-liter naturally aspirated engine. The 1.5-liter turbocharged engine delivers a maximum power of 130 kW and a peak torque of 255 Nm, with the maximum power achieved at 5500 rpm and the peak torque available between 1500 to 4000 rpm. This engine features direct fuel injection technology and an aluminum cylinder head. The 1.8-liter turbocharged engine produces a maximum power of 135 kW and a peak torque of 300 Nm, with the maximum power achieved at 5500 rpm and the peak torque available between 1750 to 4000 rpm. This engine also features direct fuel injection technology, along with an aluminum cylinder head and a cast iron cylinder block. The 2.0-liter naturally aspirated engine generates a maximum power of 104 kW and a peak torque of 178 Nm, with the maximum power achieved at 6000 rpm and the peak torque available between 4000 to 4500 rpm. This engine utilizes multi-point fuel injection technology and an aluminum cylinder head and block. 3. The Boyue employs a MacPherson independent suspension at the front and a multi-link independent suspension at the rear. The multi-link independent suspension enhances the tire's road-holding performance.
Was this review help?
5
0
Share
More Forum Discussions

How to Start a Car with Tiptronic Transmission?

Correct starting method for a tiptronic transmission car: The vehicle can only be started in P or N gear. The N gear start is used when the vehicle is to move forward immediately after starting. You can first turn on the power, press the brake, shift the gear to N, then ignite the engine, and subsequently shift to D gear to move forward directly. This avoids the transmission experiencing a reverse impact when passing through R gear after ignition in P gear. More details are as follows: 1. Parking: After the car is in the parking position, press the brake, shift the gear lever to N gear, pull up the handbrake, release the foot brake, and then turn off the engine. Finally, press the brake again and push the gear lever into P gear. Of course, this is also a meticulous protection for the transmission. 2. Temporary parking: When temporarily parking (such as waiting for a red light), whether to use N gear or D gear is not wrong, it just depends on personal habits. Temporarily stopping and pressing the brake in D gear does not harm the car because the torque converter in the transmission is equipped with a reaction wheel with a one-way clutch, which amplifies the torque from the engine crankshaft. It does not rotate at engine idle speed and only comes into play when the engine speed increases.
14
1
Share

What to Do If the Lamination Film of the Driver's License Peels Off?

If the lamination film of the driver's license peels off, you can go to the vehicle management office for a replacement. Below is relevant information about driver's license damage: 1. Relevant regulations: Article 60 of the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses" stipulates that under any of the following circumstances, the motor vehicle driver shall apply for a replacement at the vehicle management office of the issuing authority or outside the issuing area within 30 days: (1) Within the jurisdiction of the vehicle management office, the motor vehicle driver's information recorded on the driver's license changes. (2) The motor vehicle driver's license is damaged and cannot be recognized. 2. Relevant materials: When applying, you should fill out the "Motor Vehicle Driver's License Application Form" and submit the following documents and proofs: (1) The identity proof of the motor vehicle driver. (2) The motor vehicle driver's license. (3) A physical condition certificate issued by a medical institution at or above the county level or the regimental level of the military. If applying for a driver's license for a small automatic passenger vehicle for the disabled, a physical condition certificate issued by a specialized medical institution designated by the provincial health authority must be submitted.
7
0
Share

What are the symptoms of engine air leakage?

Engine air leakage symptoms include: 1. When there is leakage at the carburetor gasket, intake manifold gasket, cylinder gasket, valves, cylinders, or any other part, it will result in reduced cylinder pressure; 2. Insufficient power; 3. Increased consumption of engine oil and fuel, and even difficulty in starting. More details are as follows: 1. The airtightness of the engine is one of the important conditions to ensure its normal operation. The better the airtightness of the engine, the higher the cylinder pressure, the greater the instantaneous effective pressure generated during the engine's working stroke, the faster the combustion of the air-fuel mixture, and the less heat loss from the cooling water and exhaust gases, resulting in better power performance and fuel economy. 2. The causes of engine air leakage are: During long-term use of the engine, due to wear and tear of cylinder-piston group components, wear and erosion of valves and valve seats, and warping of the sealing surfaces of the cylinder block and cylinder head, the amount of air leakage in the cylinder increases, and the sealing performance decreases, leading to reduced engine power and increased fuel consumption.
20
2
Share

How Long Does It Take for an Engine to Be Damaged by Adding Saltwater to the Fuel Tank?

Thousands of kilometers later, the engine will be completely ruined. Salt has severe corrosive effects on bearings and piston rings, while sugar dissolves in the engine oil, increasing its viscosity, reducing lubrication, and causing damage to moving parts such as bearings and pistons. It is necessary to drain the oil immediately, flush the engine interior once, and then replace it with new oil. If the duration is short, the damage will not be significant. Below is some related information about water entering the engine: 1. Significant water ingress into the engine: If a considerable amount of water enters the engine but does not affect normal driving, though the noise is louder, it may indicate a small amount of water in the oil or fuel, requiring an oil change and cleaning of related engine components. 2. Reasons for a car stalling in water: Water entering the distributor cap can disrupt normal ignition function, while water in the engine's air filter increases intake resistance and leads to water entering the combustion chamber, preventing the spark plugs from igniting. Restarting the engine under these conditions can easily cause a hydro lock.
7
5
Share

Why can't the Ford Focus trunk be opened?

The main reasons why the Ford Focus trunk cannot be opened are: 1. Problems with the linkage rod or lock cylinder; 2. The trunk is frozen or stuck; 3. The trunk is not unlocked; 4. The trunk itself has problems, etc. Additional information: 1. When the trunk cannot be opened, you can lift the rear seat, enter the trunk, open the interior panel, and manually pull the unlocking lever to unlock it. 2. The trunk capacity of the Ford Focus hatchback is 356L, while the sedan version has a trunk capacity of 530L. 3. The Ford Focus is an A-segment family car under the Ford brand. The Focus continues Ford's kinetic design philosophy, with the chrome metal trim in front of the hood being the latest design approach of the Ford family, not only fully showcasing the Focus's dynamic and stylish appearance but also continuing the distinctive brand characteristics of the Ford family. The changes to the large-mouth grille make the front face of the Focus look more impactful, and the newly designed headlights give the Focus a very aggressive appearance.
8
5
Share

What is the meaning of wheel rim?

Wheel rim, commonly known as wheel ring, is the component installed around the wheel to support and mount the tire, forming the wheel together with the wheel spokes. The wheel rim and spokes can be integral, permanently connected, or detachable. The wheel hub is the rotating component that connects the wheel and axle, responsible for bearing the load between the tire and axle. The classification of automobile wheel rims is as follows: 1. Deep well rim: This type of rim is integral, with a deep groove in the middle of its cross-section. It has a flanged shoulder for mounting the tire bead, with the shoulder usually slightly inclined towards the center at an angle of 4 to 6 degrees. The maximum diameter of the inclined part is called the tire bead seat diameter. The deep groove in the middle of the cross-section facilitates the mounting and dismounting of the tire; 2. Flat base rim: There are many structural forms of this type of rim. The retaining ring is integral, and an open elastic lock ring is used to prevent the retaining ring from coming off; 3. Split rim: This type of rim consists of inner and outer parts. The width of the inner and outer rims can be equal or unequal, and they are bolted together. When mounting or dismounting the tire, only the nuts need to be removed. The inner rim is made with an integral flange to replace the function of the retaining ring, and the inner rim is welded to the wheel disc.
13
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.