How to reset tire pressure after replacing the central control screen?

Do Tubeless Tires Need to Be Inflated?

Tubeless tires contain gas inside, and sometimes they may experience insufficient air pressure, so they do require inflation. Below is relevant information about tubeless tires: 1. Advantages: Tubeless tires rely on the airtight layer on the inner wall and bead of the tire to ensure a good seal between the tire and the rim. The outer tire also serves as the inner tube, and there is an additional rubber sealing layer on the outer side of the bead specifically designed to retain air, providing self-sealing capabilities in case of punctures. When the tire is punctured, air does not immediately escape. The rubber sealing layer tightly grips the puncturing object, making it less prone to leaks and preventing sudden pressure loss, thereby reducing the likelihood of a blowout. 2. Precautions: To ensure driving safety, it is generally recommended to check the tire pressure once a month. Even the most airtight tires will experience natural leakage over time, and external environmental factors can also cause variations in air pressure due to the principle of thermal expansion and contraction.

9

3

Share

Do I Need to Change the Transmission Fluid When Replacing the Clutch Three-Piece Set?

Yes, you need to change the transmission fluid. When replacing the clutch three-piece set, the transmission must be removed from the vehicle, and the half-shafts on both sides of the transmission must be taken off. When the half-shafts are removed, the gear oil in the transmission will flow out. Below is an introduction to the automotive transmission: 1. Transmission: A device that changes the speed ratio and direction of motion. It is used in automobiles, tractors, ships, machine tools, and various machines to alter the torque, speed, and direction of motion transmitted from the driving shaft to the driven shaft under different working conditions. A gear-driven transmission generally consists of a housing and several pairs of gears. 2. Definition: The transmission is a gearbox that changes the transmission ratio and direction of motion. It is located between the clutch and the central drive. Its main functions are: changing the driving force and speed of the vehicle (shifting gears) when the engine speed and torque remain unchanged; allowing the vehicle to reverse (changing direction); and enabling the engine to stop without stalling (neutral gear).

20

1

Share

What is the wading depth of the Camry?

The Camry can handle wading depths of around half a meter without issues. Key operating points and precautions for wading with the Camry: 1. When wading: Ensure the engine is running normally, and the steering and braking systems are responsive and reliable. Engage a low gear and drive smoothly into the water, avoiding excessive throttle or sudden acceleration to prevent water splashing into the engine and causing it to stall. 2. While driving: Maintain steady throttle to provide the Camry with sufficient and stable power, aiming to pass through in one go. Avoid stopping, shifting gears, or making sharp turns midway, especially when the underwater surface is sandy or muddy. 3. If encountering quicksand or the Camry's wheels spinning without traction: Stop immediately. Do not force the vehicle forward or backward, and avoid pressing the throttle pedal aggressively with the clutch partially engaged. Keep the engine running and organize manpower or other vehicles to push or tow the car out to prevent sinking deeper.

12

2

Share

What type of suspension does the Great Wall C30 NEV use?

The Great Wall C30 NEV uses a MacPherson independent suspension at the front and a torsion beam non-independent suspension at the rear. Below is an introduction to the MacPherson independent suspension and torsion beam non-independent suspension: 1. The most common non-independent suspension in cars is the torsion beam suspension. This type of suspension has a simple structure, small size, occupies little space, and is relatively low-cost. 2. Many compact cars and small cars use torsion beam suspensions. This is not only to reduce costs but also because many small and compact cars do not have enough space at the rear to install a multi-link independent suspension. Using a torsion beam suspension can also increase rear passenger space and trunk space. 3. The MacPherson suspension is the most widely used suspension, with a relatively simple structure. The MacPherson suspension has only one L-shaped control arm and hardly occupies any engine compartment space. Many cars with front-mounted transverse engines use MacPherson suspensions, which are also relatively low-cost.

11

5

Share

What are the requirements for self-training a driver's license?

The prerequisite for self-training a driver's license is that the applicant must have previously obtained a driver's license. For example, if the license was canceled due to failure to renew it for two years because of going abroad or forgetting, or if the license was revoked by traffic authorities due to reasons such as traffic accidents or drunk driving, but after a certain period, the law allows reapplying for a license. These individuals can directly apply for the exam at the vehicle management office without going through a driving school. Related information about obtaining a driver's license: 1. Requirements: Individuals who meet the driving license conditions stipulated by China's public security department and wish to obtain a motor vehicle driver's license must first undergo driver training and then pass the examination conducted by the traffic management department of the public security authority. Only after passing the exam can they obtain a motor vehicle driver's license. 2. Content: The motor vehicle driver's license examination is divided into subjects covering road traffic safety laws, regulations, and related knowledge, field driving skills, and road driving skills along with safe and civilized driving knowledge. The examination content and passing standards are uniform nationwide, with corresponding test items specified according to different types of vehicles eligible for driving.

1

5

Share

What Type of Engine Oil is Suitable for the Lynk & Co 03?

The Lynk & Co 03 uses fully synthetic engine oil with a 0W-20 viscosity grade. This is because the Lynk & Co 03 is equipped with either a 1.5T or 2.0T turbocharged engine, which requires higher-performance oil for optimal engine protection. Fully synthetic oil offers superior fluidity and lubricity compared to other types of engine oils, thereby providing better protection for the engine. Below is an introduction to engine oil: 1. There are three types of engine oils used in vehicles: mineral oil, fully synthetic oil, and semi-synthetic oil. Among these, fully synthetic oil performs the best, as it can adapt to a wider range of temperatures and has a longer service life. 2. Under the same operating conditions, fully synthetic oil can protect the engine effectively even at lower viscosity levels. 3. The service life of mineral oil is approximately 5,000 kilometers, semi-synthetic oil around 6,500 kilometers, and fully synthetic oil about 10,000 kilometers. Different service intervals result in varying levels of performance and protection.

19

1

Share

How to reset tire pressure after replacing the central control screen?

Do Tubeless Tires Need to Be Inflated?

Do I Need to Change the Transmission Fluid When Replacing the Clutch Three-Piece Set?

What is the wading depth of the Camry?

What type of suspension does the Great Wall C30 NEV use?

What are the requirements for self-training a driver's license?

What Type of Engine Oil is Suitable for the Lynk & Co 03?

Where is the engine number located on the JMC Shunda?

What are the test items for Automatic Transmission Subject 2?

Why should you straighten your legs during a car crash?

Will driving a 9-seater car with a C1 license be penalized?