How to reset the tire pressure warning on Geely GS?

What is the ground clearance of the Chevrolet Orlando?

The ground clearance of the Chevrolet Orlando is 167mm. Here is an introduction to the Chevrolet Orlando: 1. The Orlando is a compact SUV launched by Chevrolet; 2. The minimum ground clearance of this car is quite average, but the chassis tuning is relatively comfortable, which aligns with the car's positioning. Below is additional information about a car's minimum ground clearance: 1. It refers to the vertical height between the chassis and the ground when the car is at maximum load; 2. The minimum ground clearance of a car represents its passability. The greater the minimum ground clearance, the better the car's passability; the smaller the ground clearance, the worse the car's passability.

16

3

Share

How to Use D/S Gear?

Both D gear and S gear in a car are forward gears. Use D gear for normal driving, and S gear can be used for overtaking and acceleration. More information about the gears is as follows: P: Parking gear, start gear. Prevents the car from rolling. R: Reverse gear. Used when reversing. N: Neutral gear. Used for temporary parking. D: Drive gear, forward gear. The transmission automatically shifts between 1st to 5th gears based on speed and throttle conditions. S: Sport mode. When this gear is engaged, the gears can be freely switched, but it increases fuel consumption. L: Low gear. The transmission stays in 1st gear and does not upshift, providing some braking function when going downhill, and can be used in situations like slopes.

12

4

Share

What are the reasons for stalling during the start in Subject 3?

Subject 3 stalling during the start reasons are as follows: 1. Releasing the clutch too quickly. The solution is to slowly release the clutch, pause momentarily when the car moves slightly, and then continue to release the clutch gradually. Also, during the start, students must avoid turning the steering wheel. If a turn is necessary, it should be done after the car starts moving. 2. Starting the engine in gear. This very basic mistake is mainly caused by nervousness during the exam, so students should develop the habit of starting the engine in neutral while learning to drive. 3. Forgetting to release the handbrake. Forgetting to release the handbrake at the start can cause the car to stall. Additionally, the handbrake must be fully released. Also, when in first or second gear, pay attention to the braking force and match the clutch if the speed is slow.

20

1

Share

What does the lock mode of a four-wheel drive vehicle mean?

Four-wheel drive vehicle lock mode refers to the four-wheel drive being turned off. This mode is only used for special road conditions such as ice, snow, gravel, and mud, and can be used when the vehicle is stuck. During normal driving, this function must be turned off, otherwise it may cause damage to the four-wheel drive system components. If this function is turned on during normal driving, there will inevitably be a speed difference between the front and rear wheels when the vehicle turns. In this state, the four-wheel drive system will forcibly synchronize the speeds of the front and rear wheels, leading to interference in the four-wheel drive power and ultimately causing damage to the four-wheel drive system components, as well as generating noise during driving.

13

1

Share

How to Determine if a Car's Air Conditioning Thermostat Switch is Faulty?

Air conditioning thermostat switch failure may exhibit the following symptoms: 1. A damaged car thermostat switch can cause the cooling system temperature to become excessively high, with the water temperature gauge needle pointing to red, the water temperature warning light flashing, and coolant boiling (commonly known as overheating). 2. During engine acceleration, noticeable metallic knocking sounds may occur, accompanied by insufficient power or even engine stalling. The main causes of thermostat switch failure include: 1. Water pipe rupture or poor joint sealing; water pump seal excessive wear or damage leading to leakage; cylinder gasket leakage. 2. Cracks in the cylinder block or cylinder head; radiator damage causing leaks; malfunctioning radiator cap intake/exhaust valves resulting in coolant leakage.

7

2

Share

What Causes the Transmission to Not Move When Engaged?

Here are the reasons and solutions for a transmission that does not move when engaged: 1. Transmission oil pan leakage. Solution: It is recommended to visit a 4S shop for inspection and repair as soon as possible. 2. The linkage or cable between the control lever and the manual valve rocker arm is loose, or the manual valve remains in the neutral or parking position. Solution: If there is looseness, it should be reinstalled and the position of the control lever should be readjusted. 3. The oil pump intake or filter screen is clogged. Solution: Clean the fuel injectors and fuel lines. 4. Severe leakage in the main oil passage. Solution: It is recommended to visit a 4S shop for inspection and repair as soon as possible. 5. The oil pump is damaged. Solution: Replace the oil pump.

18

5

Share

How to reset the tire pressure warning on Geely GS?

What is the ground clearance of the Chevrolet Orlando?

How to Use D/S Gear?

What are the reasons for stalling during the start in Subject 3?

What does the lock mode of a four-wheel drive vehicle mean?

How to Determine if a Car's Air Conditioning Thermostat Switch is Faulty?

What Causes the Transmission to Not Move When Engaged?

Is the Superb a global car?

How to Connect Bluetooth for the Honda 10th Generation Accord?

How to Maintain a Used Car?

What car has a logo with four hearts?