How to Reset the Tire Pressure on BYD Song?

1 Answers
LeValeria
07/30/25 3:06am
Regarding the method to reset tire pressure on BYD vehicles, follow these steps: 1. Inflate the tires to the normal pressure range. 2. Start the vehicle's ignition. 3. Locate the MENU button on the headlight control switch and press it to enter the menu. 4. Select the "Vehicle Information Menu" and use the option buttons on the steering wheel to access the "Tire Pressure" option in the onboard computer. 5. Press the SET button at the end and confirm the tire pressure reset as prompted. 6. Hold the "√" button on the right side of the steering wheel for a few seconds to complete the reset.
Was this review help?
3
4
Share
More Forum Discussions

What documents are required to drive a car on the road?

Documents required for driving a car on the road: The driver must carry the vehicle license, driver's license, compulsory traffic insurance label, vehicle inspection qualification label, and environmental protection label. The compulsory traffic insurance label, vehicle inspection qualification label, and environmental protection label should be affixed to the upper right side of the front windshield. Below is the relevant content introduction: Obey traffic rules: Not only must the vehicle carry all relevant documents when on the road, but it must also comply with traffic rules and avoid illegal parking. At intersections, do not run red lights. Vehicles should slow down in advance at traffic intersections and must stop outside the stop line when the traffic light signals to stop; if there is no stop line, stop outside the pedestrian crossing. When turning right without traffic lights, yield to pedestrians.
14
1
Share

What Causes the Brake Noise in Mercedes-Benz C-Class?

Mercedes-Benz C-Class brake noise can be attributed to: improper installation, defects in the brake system, and brake pad issues. Details are as follows: Improper Installation: When installing new brake pads without resurfacing the old brake discs, it leads to improper fitting. This causes the new pads to rub directly against the uneven surface of the old discs, resulting in uneven wear on the new brake pads. Defects in the Brake System: This causes the brake pads to only partially contact the brake discs, increasing the pressure per unit area and leading to noise. It is recommended to inspect components such as the calipers and guide pins. Brake Pad Issues: Harder brake pad materials are more likely to cause noise, while softer materials tend to produce sharper sounds. Consider replacing them with higher-quality brake pads.
16
0
Share

What is the material of the Prado body?

Prado body material is high-strength steel, and its body structure is a 5-door 7-seat SUV. The composition and function of automobile body materials are as follows: Composition of automobile body materials: Most car bodies on the market are still made of steel, accounting for 80% of the entire automotive industry. Other materials include fiberglass and traditional plastics (such as PE, ABS, EMA, etc.). With the development of science and technology, new materials have been widely applied to car bodies, mainly including aluminum alloys and carbon fiber composites. Function of the body: The main function of the body is to protect the driver and create a good aerodynamic environment. A good body not only enhances performance but also reflects the owner's personality. In terms of form, automobile body structures are mainly divided into two types: non-load-bearing and non-load-bearing.
12
1
Share

How to Calculate Horsepower from Diesel Engine Power?

Diesel engine power can be converted to horsepower using the formula 1kw equals 1.36 horsepower. Below is an introduction to diesel engines: 1. Advantages: Diesel engines are known for their high torque and excellent fuel efficiency. The working process of a diesel engine shares many similarities with a gasoline engine, with each working cycle also going through the four strokes of intake, compression, power, and exhaust. 2. Working Principle: In a diesel engine, the air-fuel mixture in the cylinder is ignited by compression. During operation, air enters the cylinder, and when compressed to the maximum point, the temperature can reach 500-700°C with a pressure of 40-50 atmospheres. As the piston approaches top dead center, the fuel injection system sprays fuel into the combustion chamber at extremely high pressure within a very short time. The diesel fuel forms fine droplets, mixing with the high-pressure, high-temperature air. The combustible mixture then self-ignites, rapidly expanding to generate explosive force that pushes the piston downward, performing work.
6
5
Share

How to Avoid Rear-End Collisions?

Adhering to traffic rules, maintaining a safe following distance, and controlling driving speed can help avoid rear-end collisions. Below is relevant information on determining liability for rear-end collisions: 1. If the leading vehicle did not intentionally change lanes: Each case must be analyzed specifically. Generally, as long as the leading vehicle did not intentionally change lanes, the trailing vehicle will be held responsible. In icy, snowy, or foggy weather conditions, liability for rear-end collisions is determined by traffic police after investigating the accident scene and considering all relevant factors. After a rear-end collision occurs, the driver should immediately stop the vehicle and preserve the scene, then promptly report to the police and notify the insurance company. 2. If the leading vehicle brakes suddenly: In cases where a rear-end collision is caused by sudden braking of the leading vehicle, traffic police typically assign full or primary responsibility to the trailing vehicle. Traffic regulations do not prohibit sudden braking, but they do require trailing vehicles to maintain a safe distance from the vehicle ahead. Therefore, unless the leading vehicle violated traffic rules, the trailing vehicle will be held responsible for the collision.
13
5
Share

What types of insurance should be purchased for a sedan?

Car insurance needs to include compulsory traffic insurance, third-party liability insurance, vehicle damage insurance, and no-deductible insurance, among others. Below is an introduction to relevant knowledge about car insurance: 1. Compulsory Traffic Insurance: Compulsory traffic insurance is a mandatory insurance stipulated by Chinese law, so all car owners must purchase it. If a car is driven on the road without compulsory traffic insurance, the driver will be penalized with points and fines if caught by traffic police. In severe cases, the driver may even face detention, as this is an illegal act. 2. Third-Party Liability Insurance: Third-party liability insurance (abbreviated as third-party insurance) primarily covers situations where the car collides with another vehicle while driving, with the compensation fully paid by the insurance company. 3. Vehicle Damage Insurance: Vehicle damage insurance refers to a type of commercial car insurance where the insurance company compensates within a reasonable range for damages to the vehicle caused by accidents while the insured is driving.
14
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.