How to Reset the Tire Pressure on a Land Rover Range Rover?

1 Answers
Carter
07/28/25 2:48pm
Method to reset the tire pressure on a Land Rover Range Rover: First, adjust the tire pressure to light load in the settings on the dashboard. After setting it to light load, inflate the front tires to 2.3 bar and the rear tires to 2.5 bar. Then drive for a while. If no fault is reported, the tire pressure is normal, and the reset is complete. The Land Rover Range Rover has a length of 5000 mm, width of 2073 mm, height of 1869 mm, wheelbase of 2922 mm, front track of 1693 mm, rear track of 1685 mm, and minimum ground clearance of 220 mm. It is a mid-to-large SUV equipped with full-time four-wheel drive.
Was this review help?
15
4
Share
More Forum Discussions

Can You Wash Your Car in Winter?

You can wash your car in winter. Although temperatures are low during winter, it is still possible to wash your car. It's best to choose a sunny afternoon for washing and promptly remove any water from the car's surface afterward to prevent freezing. When washing your car in winter, it's advisable to use warm water first to effectively avoid freezing. Winter car washing steps: 1. Wait for the engine to cool: In winter, the engine temperature is relatively high, and washing the car abruptly can lead to thermal expansion and contraction, which can significantly affect the engine and other components. 2. Pre-wash: Before the formal wash, a pre-wash is necessary. Professional tools are available at 4S shops for this process. 3. During the formal wash, different cleaning methods should be chosen for different parts of the car, following a top-down approach.
15
0
Share

How to Remove the ETC Device from the Car?

ETC Removal Method: The back of the ETC device is attached with double-sided tape. You can use a hairdryer to heat it up, then gently pry it off with a small plastic scraper, and finally wipe the area clean with a cloth. Note that removing the ETC device by yourself will deactivate it, so you must take your vehicle's registration certificate to the ETC service provider for reactivation. The ETC installation process is as follows: First, inspect the ETC card and the electronic tag (OBU) for any damage upon receiving the device. Press the anti-tamper button on the back of the OBU; a red light will briefly illuminate, and the OLED screen will display 'Tag Invalid, Please Insert Card,' indicating the device is functioning properly. Clean the front windshield to ensure the surface is smooth, clean, and dry. Then, peel off the protective film from the OBU's adhesive backing and attach it to the designated installation spot. Press firmly for 2-3 minutes to eliminate any air bubbles. Insert the ETC card with the front side facing the driver and the back side facing the windshield, ensuring the chip is properly inserted into the OBU device. Benefits of Installing ETC: Time-saving: Eliminates the hassle of waiting in queues; Green and eco-friendly: Promotes low-carbon travel by allowing vehicles to pass through toll stations without stopping, reducing noise and exhaust emissions, and minimizing pollution; Cost and wear reduction: Saves money by decreasing the frequency of vehicle starts and stops, thus reducing wear and fuel consumption. Users also enjoy a 5% discount on toll fees; Improved efficiency: ETC lanes can theoretically increase vehicle throughput by 2-3 times, making traditional ETC systems more updated, faster, and more technologically advanced. Compared to license plate payment, ETC technology is more mature and advantageous.
11
3
Share

Which fuse is for the cigarette lighter in a Volkswagen Polo?

The following is relevant information about the Volkswagen Polo: 1. Fuse Box: The fuse box in the new Volkswagen Polo can be opened by simply prying it with your hand. Since car fuses are housed in the fuse box, they generally do not require special maintenance. However, it is important to note that if the fuse box cover is missing, the fuses should not be left exposed to avoid short circuits. Additionally, when covering fuses, do not use other materials as substitutes, as the fuse box material is specifically designed for insulation and high-temperature resistance. Using improper materials to cover fuses may pose a fire hazard. 2. Familiarize Yourself with Fuse Locations: If individual electrical components such as the cigarette lighter, power windows, air conditioning, or headlights stop working, and you hear a current or relay sound when turning them on, it is likely that a fuse has blown. If the vehicle fails to start, avoid repeatedly attempting to ignite the engine, as this can lead to excessive battery discharge. If the vehicle's lights remain bright, the issue may be a blown fuse responsible for the starter motor, which can melt due to excessive instantaneous current. When electrical components stop working, the first step is to check whether the fuse has blown before proceeding with further troubleshooting. Therefore, knowing the locations of the fuses in your vehicle is crucial. 3. High-Power Headlights: Be cautious when installing high-power headlights. Modifying headlights with excessive power can easily blow fuses, so it is necessary to promptly replace them with higher-current fuses and power cables to prevent overheating due to excessive current. Similarly, installing high-power audio systems can also cause fuses to blow. When adding high-power electrical components, always pay attention to the current requirements and replace the corresponding fuses accordingly. Reputable modification shops typically address this issue properly.
10
2
Share

Should the Nissan Tiida ECO Mode Be Turned On?

ECO mode works best when turned on in congested urban traffic conditions. In such scenarios, strong power is not required, and the frequent stops and starts lead to higher fuel consumption. Activating ECO mode not only reduces fuel consumption but also provides a more comfortable driving experience. Instances where ECO mode is unnecessary: There are a few situations where ECO mode is not needed: 1. When driving at high speeds (up to 100km/h), even if ECO is turned on, the vehicle's computer will prioritize speed, causing the ECO mode to automatically deactivate. 2. When high torque output is required, such as when climbing hills, the engine computer will prioritize ensuring sufficient power to drive the vehicle, and the ECO mode will automatically deactivate. Location of the ECO button: The ECO button is generally located on the left side of the car, marked with the letters 'ECO'. Some models feature a green button, making it easily identifiable.
12
2
Share

How long is it appropriate to warm up the car before driving?

It is appropriate to warm up the car for about one minute before driving. Warming up the car means keeping the car in an idle state after starting it. When the car is not in motion, the engine is not running, and the oil does not circulate. If the car remains stationary for a long time, the oil will settle at the bottom of the oil pan. If you start driving immediately after ignition, the oil cannot reach all parts of the components in time, failing to provide any lubrication, which can damage the engine. Warming up the car should not take too long, but it should not be completely ignored either, as this step is crucial. It is recommended that car owners pay attention to this, especially during cold winter months when warming up the car becomes even more important. This step must not be skipped, otherwise the car may suffer damage.
16
3
Share

What is the fault when the EPC light is on in a Jianghuai diesel vehicle?

There are two possible reasons for the EPC light being on in a Jianghuai diesel vehicle. One is a dirty throttle valve, which should be cleaned. The other situation is that the brake light is not working, and the brake switch and wiring need to be checked. Below is more information about Jianghuai Automobile: 1. Company Profile: Anhui Jianghuai Automobile Group Corp., Ltd. is a comprehensive automobile enterprise group that integrates the research, production, and sales of a full range of commercial vehicles, passenger vehicles, and powertrains, focusing on "advanced energy-saving vehicles, new energy vehicles, and intelligent connected vehicles," covering numerous fields such as automobile travel and financial services. 2. Company Business: The group has formed four core sectors: vehicle business (passenger vehicles, commercial vehicles, buses, new energy), core components, automobile travel, and automobile services, striving to build a comprehensive automobile service platform with a "full ecological chain, full industrial chain, and full value chain."
12
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.