How to reset the tire pressure monitoring light on Volkswagen Lavida?

2 Answers
KalebDella
07/29/25 5:26pm
Methods to reset the tire pressure monitoring light on Volkswagen Lavida are as follows: 1. For Lavida Plus, with the ignition switch on, briefly press the OK button repeatedly to select the tire pressure display and 'Tire Pressure' function. Hold for about 3 seconds until a beep is heard, and the tire pressure monitoring light will be deactivated. 2. After changing tire inflation pressure or replacing wheels, a reset is required to clear the warning light. Turn on the ignition switch, press and hold the SET button of the tire pressure control system (the black button located on the front panel near the gearshift lever) until the indicator light on the dashboard illuminates. Confirm that the new parameters are stored and the light goes off, indicating the tire pressure light reset is complete. 3. Press the black stalk on the dashboard and turn the ignition key three times from off to position 2 (without starting the vehicle) to reset. If it's near the service time, try not to delay the maintenance. When the ignition is in the ON position, the 'SERVICE' indicator on the display will flash and disappear after starting the engine, indicating that maintenance is required. After maintenance, the service light should be reset.
Was this review help?
4
3
Share
Josiah
08/14/25 8:21am
I've been driving a Volkswagen Lavida for over five years and have encountered the tire pressure monitoring light issue several times. The most straightforward solution is to first check the actual tire pressure of all four tires, ensuring they're inflated to the standard values (marked on the inside of the fuel filler cap). Then, sit in the car, turn the key to the power-on position without starting the engine, locate the vehicle settings menu on the center console screen, enter the tire options, and select tire pressure reset. At this point, the tire pressure light on the dashboard will flash a few times and then turn off. Drive the car for about ten minutes, and the system will automatically reset. If your car doesn't have a large center console screen, you can try holding down the SET button next to the gear lever for five seconds. A beep sound indicates the reset has started. Remember to avoid bumpy roads after the reset and maintain a steady speed for a while to allow the system to stably record data, otherwise the light might come on again.
Was this review help?
4
5
Share
Expand All
More Forum Discussions

How to Solve the Engine Immobilizer Authentication Failure Issue on Baojun 510?

Fellow car owners should first check their car keys. The remote key fob contains a dedicated module specifically for engine starting. Simply pry open the casing, remove the old battery and replace it with a new one.
8
1
Share

How to Remove the Fuel Pump on a Buick Excelle?

First remove the rear seat to expose a black metal cover secured by four screws. Unscrew these to reveal the fuel pump. Disconnect all wiring connections, then use a specialized fuel pump removal tool to unscrew and extract the unit.
9
1
Share

How to fix the peeling dashboard of a Buick Excelle?

If the dashboard warping issue occurs during the car's warranty period, you can contact after-sales service for relevant handling. If the car's warranty period has expired but the dashboard warping issue occurs, you can go to an auto repair shop for handling.
13
2
Share

What Causes the ABS Light to Illuminate in a Jaguar?

ABS light illumination can occur in various states, with different causes and solutions for each state, as detailed below: State 1: ABS warning light remains constantly lit (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS control unit from determining the vehicle speed and wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the contaminants from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal operation. Cause 2: Poor signal transmission due to loose system wiring connections or poor contact in the ABS relay, leading to system malfunction. Solution: Inspect wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple electrical components are in use, the battery voltage drops below 10.5V. As engine speed increases, voltage rises, and the ABS light turns off. This may also occur due to insufficient power supply voltage to the ABS system, such as poor terminal contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light remains lit after engine startup until the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor electrical connector contact in the ABS hydraulic valve body; ABS control unit malfunction. Solution: Loosen and then retighten the grounding screw on the hydraulic valve body, cleaning the contact surface if necessary; check for enlarged connector gaps; replace the ABS or ABS/ASR control unit. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS control unit detects a significant discrepancy between rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's specified tire and wheel rim specifications, typically listed on the fuel tank cap sticker. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and manually push the brake switch linkage fully downward, then release the pedal to complete self-positioning; replace the brake light switch if necessary. If the ABS warning light is illuminated, it is advisable not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's trajectory, posing significant safety risks.
17
1
Share

How to adjust the ambient lighting in the 2021 Audi A6L?

You can adjust the interior ambient lighting through the MMI display. Press the CAR button to select the system and enter the background lighting interface. The ambient lighting at the front footwells, rear footwells, front door panels, and rear door panels can all be set via the MMI.
2
0
Share

How to Repair Cracked Leather in Car Interior?

Use a soft brush and a slightly damp towel to thoroughly clean the leather that needs repair or has wrinkles. Sand the leather surface that requires repair with water sandpaper, and remove any already cracked leather as well. Apply leather repair paste to the surface that needs fixing, spray a layer of primer on the leather surface, then complete the coloring within 60-150 seconds.
13
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.