How to reset the tire pressure indicator light on the Octavia?

3 Answers
DeEmersyn
07/29/25 2:23am
Method to reset the Octavia's tire pressure indicator light: First, ensure that all four tires have normal pressure. With the tire pressure at the correct level, turn on the ignition and press and hold the tire pressure monitoring switch until you hear an alarm sound, then release to reset the tire pressure indicator light. The Octavia is a vehicle launched by SAIC Volkswagen, with dimensions of 4675mm in length, 1814mm in width, and 1460mm in height, and a wheelbase of 2686mm. In terms of exterior design, this car adopts Škoda's new family design language, showcasing a minimalist style, and the two-tone floating exterior rearview mirrors add a sense of layering to the body. For the suspension, the front uses a MacPherson independent suspension, while the rear employs a torsion beam non-independent suspension.
Was this review help?
17
4
Share
LeilaniRose
08/12/25 12:28pm
As a long-time owner of a Skoda Octavia, don't rush to reset when the tire pressure light comes on. It's best to first park in a safe location and check the air pressure of all tires. Use a simple pressure gauge to measure whether they meet the recommended values on the label inside the door frame, and don't forget the spare tire—some vehicles can trigger the light due to spare tire issues. After checking, get back in the car, turn the key to the ON position without starting the engine, and look for the SET button near the center console. It's usually a small round button with a tire pressure icon—hold it down for five to ten seconds without releasing until the indicator light turns off. If the light comes back on after turning off, there might be an actual leak or sensor malfunction, and you should visit a repair shop. Taking a few minutes to check tire pressure before daily driving not only avoids the hassle of the light coming on but also extends tire life and ensures safety.
Was this review help?
20
5
Share
Expand All
VonJuliana
10/02/25 4:05am
We have a Skoda Octavia as our daily driver, and the tire pressure warning light has come on a few times. The solution is straightforward: Park the car and first measure the tire pressure using a portable pressure gauge at home or the tools at a gas station to ensure each tire, including the spare, matches the recommended values in the manual. Then, get in the car, turn on the ignition without starting the engine, locate the SET button marked near the steering wheel, and press and hold it for three to five seconds until the light goes off. Don’t rush the process—if the light doesn’t turn off, repeat the steps. Make it a habit to check the tire pressure monthly, and while you’re at it, inspect the tread depth to avoid sudden skidding.
Was this review help?
15
1
Share
Expand All
More Forum Discussions

How to Solve the Engine Immobilizer Authentication Failure Issue on Baojun 510?

Fellow car owners should first check their car keys. The remote key fob contains a dedicated module specifically for engine starting. Simply pry open the casing, remove the old battery and replace it with a new one.
8
1
Share

How to Remove the Fuel Pump on a Buick Excelle?

First remove the rear seat to expose a black metal cover secured by four screws. Unscrew these to reveal the fuel pump. Disconnect all wiring connections, then use a specialized fuel pump removal tool to unscrew and extract the unit.
9
1
Share

How to fix the peeling dashboard of a Buick Excelle?

If the dashboard warping issue occurs during the car's warranty period, you can contact after-sales service for relevant handling. If the car's warranty period has expired but the dashboard warping issue occurs, you can go to an auto repair shop for handling.
13
2
Share

What Causes the ABS Light to Illuminate in a Jaguar?

ABS light illumination can occur in various states, with different causes and solutions for each state, as detailed below: State 1: ABS warning light remains constantly lit (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS control unit from determining the vehicle speed and wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the contaminants from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal operation. Cause 2: Poor signal transmission due to loose system wiring connections or poor contact in the ABS relay, leading to system malfunction. Solution: Inspect wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple electrical components are in use, the battery voltage drops below 10.5V. As engine speed increases, voltage rises, and the ABS light turns off. This may also occur due to insufficient power supply voltage to the ABS system, such as poor terminal contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light remains lit after engine startup until the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor electrical connector contact in the ABS hydraulic valve body; ABS control unit malfunction. Solution: Loosen and then retighten the grounding screw on the hydraulic valve body, cleaning the contact surface if necessary; check for enlarged connector gaps; replace the ABS or ABS/ASR control unit. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS control unit detects a significant discrepancy between rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's specified tire and wheel rim specifications, typically listed on the fuel tank cap sticker. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and manually push the brake switch linkage fully downward, then release the pedal to complete self-positioning; replace the brake light switch if necessary. If the ABS warning light is illuminated, it is advisable not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's trajectory, posing significant safety risks.
17
1
Share

How to adjust the ambient lighting in the 2021 Audi A6L?

You can adjust the interior ambient lighting through the MMI display. Press the CAR button to select the system and enter the background lighting interface. The ambient lighting at the front footwells, rear footwells, front door panels, and rear door panels can all be set via the MMI.
2
0
Share

How to Repair Cracked Leather in Car Interior?

Use a soft brush and a slightly damp towel to thoroughly clean the leather that needs repair or has wrinkles. Sand the leather surface that requires repair with water sandpaper, and remove any already cracked leather as well. Apply leather repair paste to the surface that needs fixing, spray a layer of primer on the leather surface, then complete the coloring within 60-150 seconds.
13
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.