···
Log in / Register

How to Reset the Remaining Maintenance Mileage on Binrui?

1 Answers
McMarley
09/05/25 3:37am
First, start the vehicle by powering it on; there's no need to start the engine. After powering on, press the menu button on the steering wheel, and corresponding prompts will appear on the dashboard. Then, use the Binrui's 'Left-Right Cycle' button to switch to the vehicle settings. Next, press the 'Confirm' button in the center of the Binrui to enter the vehicle settings system. Locate the Binrui's remaining mileage option and click to enter. After entering the remaining mileage option, select the 'Clear Mileage' option and confirm to complete the process.
Was this review help?
16
4
Share
More Forum Discussions

How to Set Up Touch Lock for Magotan?

When opening the door, retract your thumb towards the palm and pull the door handle without touching the indentation. To lock the car, simply touch the indentation with any finger; "Mag" symbolizes confidence, decisiveness, and dynamism; "otan" represents soaring, surpassing, and passion.
10
4
Share

How to Repair a Slightly Bulging Tire?

If the bulge is relatively small, some repair shops may use a hot patch method for repair. Hot patching, also known as vulcanization, fundamentally addresses the issue of broken cord threads. Hot patching requires a higher level of technical skill from the technician, and it is generally recommended to directly replace the tire with a new one rather than attempting a repair.
6
5
Share

What to Do When the Car Remote Lock Fails?

Due to sealing issues, the key may become damp or get oxidized by dirt inside. Clean it thoroughly and reinstall to test if it functions properly. Poor contact on the circuit board requires soldering, such as with a soldering iron. It is recommended to take it to a precision electronics repair shop or a mobile phone repair center for professional handling.
7
2
Share

How to Completely Remove Spray Paint from a Car?

After wiping, wait for a while to allow the spray paint to soften and dissolve; otherwise, the original car paint may lose its luster due to wiping. You can also use brake fluid or other substitutes for gasoline. Alcohol (industrial alcohol) can be used to wipe off the spray paint. Take a soft cotton cloth, dip it in alcohol, and gently wipe the sprayed area until the surface becomes completely smooth.
4
5
Share

What are the symptoms of a damaged AT automatic transmission?

AT automatic transmission damage may manifest as abnormal noises, overheating, or slipping issues. Below are detailed explanations: Transmission Abnormal Noises: Symptoms: Unusual sounds or loud noises from the transmission during idling, driving, or under high load, with irregular, dull noises during gear shifts. Causes: Prolonged high temperatures degrade the transmission fluid's anti-wear and lubricating properties, leading to wear or severe damage to bearings, gears, or gear surfaces. Action: Consult transmission specialists immediately for professional advice before proceeding. Transmission Overheating: Symptoms: The computer alerts to high transmission temperature while driving, or the transmission feels excessively hot to touch after driving. Causes: Inability to effectively control temperature under high load, or slipping can cause overheating. In some dual-clutch transmissions, friction from clutch plates during low-speed crawling generates excessive heat. Action: Pull over and let the vehicle rest for a few minutes before restarting. Seek professional repair if the issue persists. Transmission Slipping: Symptoms: Engine revving without corresponding speed increase when accelerating (similar to pressing the throttle in P or N gear), or normal driving on flat roads but poor uphill performance with high engine RPM. Causes: Excessive hydraulic fluid creating bubbles when agitated, or worn/burnt clutch/brake friction materials.
8
0
Share

How to Interpret a Three-Light Traffic Signal?

When encountering a traffic signal with three circular lights arranged horizontally while driving, the direction displaying a green light indicates permission to proceed, while a red light prohibits passage. In addition to the three circular signal lights mentioned above, there may also be arrow signal lights. The left arrow corresponds to left turns, the middle arrow to straight-through movement, and the right arrow to right turns. When needing to proceed, you may pass through the intersection when the light corresponding to your intended direction of travel displays green; directions showing red lights are prohibited from entry.
15
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.