How to Reset the Oil Maintenance Light on the Benben?

[TannerFitz]

The method to reset the oil maintenance light on the Benben is as follows: With the engine turned off, press and hold the TRIP button while turning the key to the ON position. After approximately three seconds, you will see the maintenance light flash twice. Then, release the TRIP button and press it again for about three seconds. Additional relevant information is provided below: 1. The small wrench icon on the dashboard is a factory setting that illuminates when the vehicle reaches a certain mileage or time interval, reminding the owner to perform timely maintenance checks. 2. The Changan Benben is a model under the Changan Automobile brand. Its body dimensions are 3525mm in length, 1650mm in width, and 1550mm in height, with a wheelbase of 2365mm. In terms of exterior design, the Benben features a high waistline and two muscular lines on the engine hood, combined with the body light design, creating a three-dimensional and layered overall appearance.

[LeAriana]

I used to reset the maintenance light on my car by myself, and it's quite simple for the Benben. First, make sure the maintenance has been done, otherwise resetting it is meaningless. The specific steps are: turn off the engine first, then turn the key to the second position (the position where the engine is not started but the power is on). Then find a button on the dashboard called ODO or TRIP, usually a small plastic button, and hold it down without releasing. You'll see the wrench icon flashing, and after a few seconds, it will go off by itself. This completes the reset. Remember to operate in the power-on state, and don't start the engine. I recommend changing the engine oil every 5,000 kilometers or so to keep the engine lubricated and reduce carbon buildup. If the light comes on again before the maintenance period, it might be an oil pressure issue, and you should check it immediately. Developing good habits makes driving smoother and safer.

[Madeleine]

The maintenance light is a reminder function; when it comes on, it's time to change the oil. Ignoring it might mislead you. Let me share how to reset it. After turning off the engine, rotate the key to the ON position only—do not start the ignition. Then, locate the odometer button or a similar small button on the dashboard and hold it down. Keep an eye on the indicator light; it should turn off in about 5 to 10 seconds, indicating a successful reset. If the light keeps coming on, remember to check whether the oil has deteriorated or is leaking. I also make it a habit to regularly inspect the coolant and tire pressure, as these small details can extend the car's lifespan and avoid major repairs. Overall, resetting isn't difficult, but be sure to confirm the oil quality is fine before doing it.

[GeorgeLynn]

Resetting the oil light on my Benben is quite simple, let me quickly walk you through the steps. Turn off the engine, then rotate the key to the ACC or ON position to power up. There's an ODO button or TRIP button on the dashboard, just press and hold it for more than five seconds until the wrench icon disappears. This method works for most small-displacement cars. If the light comes on, it means you should change the oil as soon as possible—don't delay too long, or it could cause serious engine wear. I always keep some spare oil in the car for emergency top-ups. The whole process takes just a minute or two.

[SpencerAnn]

The basic method to reset the oil light is to turn off the engine and rotate the key to the second position (accessory mode without starting). Then press and hold the button on the dashboard while watching the indicator light - success is achieved when it lights up and then turns off. This design is commonly used in Benben vehicles. It's recommended to perform this operation after parking and shutting off the engine, not while driving. Be patient during operation as the button position might not be obvious. Afterwards, check the oil dipstick level - maintaining a medium level is sufficient. A constantly illuminated light can be annoying, so it's best to address it promptly.

[JaxsonMarie]

Resetting the maintenance light is a routine operation. In the Benben car, turn the key to the ON position after turning off the engine. Locate the TRIP button on the dashboard and hold it for five seconds until the light goes off. Don't forget to reset it after each maintenance, as it reminds based on time or mileage. I also regularly check the oil color and viscosity, and never miss the oil change time. If the light fails to reset, check if the fuse or wiring harness is loose. Overall, maintaining good car condition is a key step to prevent the light from coming on, and it can also save some repair costs.