How to Reset the MINI Brake Pad Warning Light?

1 Answers
McNaomi
07/29/25 11:49pm
When the warning light is on, first insert the remote key, then without pressing the brake pedal, press the start/stop engine button. All dashboard lights will illuminate. Then, hold the reset button on the dashboard for about 8 seconds. Here are some tips for replacing brake pads: 1. Engage the handbrake and loosen the hub nuts of the wheel where the brake pads need to be replaced. Use a jack to lift the car and remove the tire. Before working on the brakes, it's best to spray the brake system with a dedicated brake cleaner to avoid inhaling dust particles, which can be harmful to health. 2. Remove the screws of the brake caliper. 3. Secure the brake caliper with a rope to prevent damage to the brake lines. Then remove the old brake pads. 4. Use a C-clamp to push the brake piston all the way back. Install the new brake pads. 5. Reinstall the brake caliper and tighten the caliper screws to the specified torque. Put the tire back on and slightly tighten the hub nuts. 6. Lower the jack and fully tighten the hub nuts. 7. Since the brake piston was pushed all the way in during the replacement process, the brake pedal may feel loose initially. Press it several times in succession to restore normal operation.
Was this review help?
16
0
Share
More Forum Discussions

Should Subaru Use 92 or 95 Octane Gasoline?

Subaru's turbocharged models use 95 octane gasoline; naturally aspirated models use 92 octane gasoline. More information about 92 and 95 octane gasoline is as follows: 1. The octane ratings of 92 and 95 gasoline represent the fuel's anti-knock performance. The higher the octane number, the greater the isooctane content, indicating better anti-knock performance. 2. The higher the compression ratio, the higher the octane rating of the gasoline used: For engines with a compression ratio greater than 9:1, it is recommended to use gasoline with an octane rating above 90; for engines with a compression ratio greater than 9.5:1, it is best to use gasoline with an octane rating above 92; when the compression ratio is greater than 10:1, it is best to use 95 octane or higher-rated gasoline.
12
5
Share

Which generation of EA888 is the DBF model?

dbf model is the third generation of EA888, the second generation has been discontinued, and now the third generation is uniformly used. The specific introduction is as follows: Methods to determine which generation of EA888 it is: According to the oil-gas separator model: The first and second generation models have different oil-gas separator models, but it is difficult to distinguish between the first and second generations from appearance. Distinguishing from appearance: The second and third generations can be distinguished from appearance because the oil filler port positions are different. The third-generation engine's oil filler port is on the left rear side, while the second-generation's oil filler port is on the left side near the middle. Overall, the third generation has significant improvements and differs greatly from the first and second generations. The main differences lie in the internal mechanisms and materials, while the first and second generations are difficult to distinguish from appearance and require disassembling some parts to determine. The Volkswagen EA888 engine is a newly designed engine by Volkswagen, with main models including 1.8L and 2.0L displacements. The engine integrates technologies such as direct injection, turbocharging, and variable valve timing, achieving a balance between power and economic environmental protection.
2
2
Share

What is the highway fuel consumption of the Tang DM?

The Tang DM currently has 1 model available for sale. The 2021 2.0T Automatic Flagship model, equipped with a 192 horsepower engine, has an NEDC fuel consumption of 9L per 100 kilometers. Different models of the Tang DM have varying fuel tank capacities. The distance that can be covered on a full tank of fuel is as follows: For the model equipped with a 192 horsepower engine, the fuel tank capacity is 68L, and the distance that can be covered on a full tank is 68/9*100=756KM. The fuel consumption of a car is directly influenced by five major factors: driving habits, the car itself, road conditions, natural wind, and environmental temperature. Specific factors that can increase fuel consumption include: Driving habits: Aggressive driving behaviors such as sudden acceleration, frequent overtaking, and not easing off the throttle before encountering a red light can increase fuel consumption. The car itself: Cars with larger engine displacements generally consume more fuel than those with smaller displacements because larger displacements usually mean higher power output, requiring more gasoline for combustion. Heavier cars also tend to have higher fuel consumption because greater weight requires more driving torque. Road conditions: Driving on unpaved roads, muddy roads, soft surfaces, or mountainous terrain increases resistance and fuel consumption. Natural wind: Driving against the wind or on windy days increases the car's resistance, leading to higher fuel consumption. Low environmental temperatures: When the engine block is cold, the injected gasoline does not atomize easily during cold starts, requiring more gasoline for combustion, which increases fuel consumption. Additionally, in low temperatures, the engine's computer may control the engine to run at higher RPMs to warm up, further increasing fuel consumption.
11
5
Share

What is the displacement of the Mercedes-Benz A180?

The displacement of the Mercedes-Benz A180 is 1.3T. Displacement is a specialized term in hydraulic transmission, referring to the volume of fluid inhaled or discharged per stroke or cycle. Below is a related introduction to the Mercedes-Benz A180: In terms of body dimensions: The Mercedes-Benz A180 is a compact sedan launched by Mercedes-Benz, serving as an entry-level model in the brand's lineup. In terms of body dimensions, the Mercedes-Benz A180 measures 4622mm in length, 1796mm in width, and 1454mm in height, with a wheelbase of 2789mm. In terms of the powertrain: The Mercedes-Benz A180 is equipped with a 1.3T turbocharged engine, which is an inline four-cylinder engine. This engine delivers a maximum power of 100 kW, a maximum torque of 200 Nm, and a maximum horsepower of 136 PS. It is paired with a 7-speed dual-clutch transmission. In terms of model configuration: The Mercedes-Benz A180 features a MacPherson strut front suspension and a torsion beam non-independent rear suspension.
10
0
Share

What is the fuel tank capacity of the Leiling 1.2T in liters?

The fuel tank capacity of the Leiling 1.2T is 50 liters, as officially announced. Owners who have purchased the Leiling 1.2T can also check this information on the vehicle's configuration sheet. The Leiling 1.2T uses 92-octane fuel, with a fuel consumption of 5.6-5.7L per 100 kilometers. A full tank can cover a distance of 877-892 kilometers. During daily driving, it is essential to monitor the remaining fuel level in the tank. This is typically observed through the fuel gauge inside the vehicle. If there are no other issues, the fuel level will be accurately reflected on the gauge. The fuel gauge usually has 5 to 6 segments, and it is advisable to refuel when only 2 segments remain to avoid running out of fuel midway. During actual refueling, the amount of fuel added may exceed the calibrated capacity. This is because the fuel tank capacity specified by the manufacturer is measured from the bottom of the tank to the safety limit, and there is additional space from the safety limit to the tank opening. This extra space ensures that the fuel can expand when temperatures rise without overflowing. If fuel is added up to the tank opening during refueling, the actual amount of fuel added may exceed the calibrated tank capacity.
12
3
Share

Should Polo Use 92 or 95 Octane Gasoline?

Polo can use 92 octane gasoline. Below are the differences between 92 and 95 octane: 1. Different compositions: It can be confirmed that there is no difference in the quality of 92 and 95 octane gasoline; their quality is the same. Analyzing their main components, 92 octane gasoline consists of 92% isooctane and 8% n-heptane, while 95 octane consists of 95% isooctane and 5% n-heptane. The reason 95 octane gasoline is slightly more expensive is due to the higher proportion of isooctane. Isooctane also has another function, which is anti-knock. This means that the higher the proportion of isooctane, the better the anti-knock performance. 2. Different prices: A tank of 95 octane gasoline is slightly more expensive than 92 octane. 3. Different power outputs: 95 octane gasoline, with its higher octane rating, is suitable for engines with higher compression ratios. This is because as the engine speed increases, the ignition timing in the cylinder advances. When the speed reaches a critical point, the air-fuel mixture in the cylinder may ignite prematurely before the spark plug fires, a phenomenon known as knocking. Increasing the octane rating of gasoline can effectively improve anti-knock performance.
12
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.