How to Reset the Maintenance Reminder on Volkswagen Lamando?

1 Answers
SanLily
07/29/25 7:25pm
To reset the maintenance reminder on the Lamando, follow these methods: Method 1: 1. First, turn off the ignition switch to shut down the vehicle. 2. Then, use your left index finger to press and hold the "0.0" button located below the instrument panel. 3. Next, use your right hand to turn on the ignition switch while keeping the "0.0" button pressed until the maintenance service message appears in English on the instrument panel, then release the button. 4. After releasing, press the "0.0" button below the instrument panel once again within 30 seconds. 5. Once the above steps are completed, the maintenance reminder light will be reset. Method 2: 1. Turn on the ignition switch and press the CAR button located at the bottom left. 2. Tap the settings icon at the bottom right of the screen, then scroll up to find the maintenance option. 3. Click on "Reset Maintenance Information" and confirm to clear the maintenance reminder light.
Was this review help?
5
3
Share
More Forum Discussions

What Causes Idle Vibration After the Car Warms Up?

Reasons for idle vibration after the car warms up: 1. The idle speed motor is damaged and cannot adjust the opening of the air valve; 2. The fuel injector is clogged or the fuel pump is faulty, the fuel line is obstructed; throttle body failure, air leakage prevents proper control of the air intake; 3. The intake sensor is faulty, leading to uncontrolled air intake; 4. Engine control logic error, unable to stabilize idle speed. Solutions for idle vibration after the car warms up are: 1. Clean the fuel system, check the idle speed motor for carbon buildup and clean if necessary; 2. Inspect the spark plugs for excessive carbon deposits and replace them if needed; 3. Check the fuel pressure and replace components as necessary.
2
2
Share

Where is the coolant reservoir located in the 10th generation Accord?

The coolant reservoir in the 10th generation Accord is located in the engine compartment. Coolant is a special additive-containing liquid primarily used in liquid-cooled engine cooling systems. It offers excellent performance characteristics such as freeze protection in winter, boil-over prevention in summer, and year-round anti-scaling and anti-corrosion properties. Coolant composition: The main components of coolant are: 50% purified water, 40% methanol, and 10% other substances. Types of coolant: Coolants are generally classified into three types: ethanol-water type, glycerin-water type, and ethylene glycol-water type. Can different coolants be mixed? It is necessary to use the same brand of coolant. Different brands may have varying production formulas, and mixing them could cause chemical reactions between additives, rendering them ineffective. How to choose coolant: The basic indicators for coolant are freezing point and boiling point. Market-available coolants come in specifications like -15°C, -25°C, -30°C, and -40°C freezing points. Generally, it's advisable to choose a coolant with a freezing point at least 10°C lower than the lowest temperature in your region.
19
5
Share

Is the Ferrari F12 naturally aspirated?

Ferrari F12 is naturally aspirated. This car is equipped with a 6.3-liter V12 naturally aspirated engine, delivering a maximum power of 741 horsepower and a maximum torque of 690 Nm. The maximum power is achieved at 8,250 rpm, and the maximum torque is reached at 6,000 rpm. The engine is paired with a 7-speed dual-clutch transmission. The Ferrari F12 is a front-engine sports car under the Ferrari brand, with body dimensions of 4,618 mm in length, 1,942 mm in width, and 1,273 mm in height. The F12 features an aluminum body frame made from 20 composite materials, utilizing laser welding technology to achieve near-perfect body tolerances. The body extensively incorporates carbon fiber components to perfectly balance lightweight construction with structural strength requirements.
20
0
Share

What is the reason for the Volkswagen Lavida's battery running out after being parked for 3 days?

According to the capacity of a car battery, it is abnormal for the vehicle to run out of power after being parked for 3 days. Possible reasons include poor battery quality leading to insufficient stored power or leakage, or unswitched-off electrical appliances after the vehicle is locked. A car battery, also known as a storage battery, is a type of battery that works by converting chemical energy into electrical energy. The battery of a Volkswagen Lavida typically needs replacement every 3 to 5 years. Under normal conditions where the vehicle's alternator charges properly and there are no electrical leakages or grounding issues, the Lavida's battery can generally last for more than 3 years. The Lavida is a compact sedan under the Volkswagen brand, with body dimensions of 4670 mm in length, 1806 mm in width, and 1474 mm in height, and a wheelbase of 2688 mm. Here are some relevant details: If the battery runs out after the vehicle has been parked for 3 days, you will need to jump-start the vehicle. Drive the car to a repair shop, where the battery can be charged first. Once the battery is fully charged, use a battery tester to measure its capacity and compare it with the original battery capacity marked on the vehicle to see the difference. A significant difference indicates that the battery has aged, and insufficient capacity can cause the battery to run out after just 3 days of parking. If the capacity is sufficient, measure the vehicle's discharge current using an ammeter. Normally, for vehicles with fewer control modules, the discharge current should be between 12-20 milliamperes. For vehicles with more control modules, the discharge current should not exceed 55 milliamperes. An abnormal discharge current indicates that there is a component in the vehicle causing a discharge, leading to the battery running out after 3 days. The issue can be resolved by identifying and fixing the source of the leakage. Battery maintenance tips for the Lavida include: Avoid parking the car in open parking areas for extended periods; In winter, when the engine is harder to start, each attempt to start the car should not exceed 5 seconds, with a minimum interval of 15 seconds between attempts; Clean the battery terminals periodically.
4
3
Share

What is the procedure to reset the tire pressure light on a 2012 Mini?

The steps to reset the tire pressure on a 2012 Mini: First, turn on the ignition, then press and hold the tire pressure monitoring reset button until you hear a "ding" sound before releasing it. The tire pressure monitoring system will then store the current normal tire pressure data, automatically clear the previous data, and finally, the warning light on the dashboard will turn off, completing the tire pressure reset. Precautions for inflating tires: Always use a pressure gauge to check the tire pressure to avoid overinflation, which can cause the tire to burst. After stopping the vehicle, wait for the tires to cool down before inflating, as driving increases tire temperature, affecting the pressure. Check the valve stem. If the valve stem and core are not properly aligned, have protrusions, depressions, or other defects, it will be difficult to inflate and measure the pressure. Ensure cleanliness when inflating. The air being pumped in should not contain moisture or oil, as this can deteriorate and damage the inner tube rubber. Do not exceed the standard pressure significantly and then release air, nor should you overinflate after being unable to inflate for a long time while traveling. Exceeding the standard pressure too much can cause excessive stretching of the cords, reducing their strength and affecting the tire's lifespan.
3
4
Share

How to Check an Oxygen Sensor?

Oxygen sensor inspection method: The condition can be judged by observing its color. The normal color of the oxygen sensor tip is light gray. Any color change indicates the oxygen sensor has a fault or potential failure. A black-tipped oxygen sensor is caused by carbon contamination. After removal, the carbon deposits should be cleaned off. If the oxygen sensor tip appears reddish-brown, it indicates lead contamination, which results from using leaded gasoline in the vehicle. The function of the oxygen sensor is to measure whether there is excess oxygen in the exhaust gas after engine combustion (i.e., oxygen content) and convert the oxygen content into a voltage signal transmitted to the engine computer. This enables the engine to achieve closed-loop control targeting the excess air factor, ensuring the three-way catalytic converter maintains maximum conversion efficiency for the three pollutants in the exhaust: hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NOx), thereby maximizing the conversion and purification of emission pollutants.
7
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.