How to reset the maintenance reminder on the Lavida?

What Causes the Brake Pedal to Be Hard to Press and the Car Unable to Start?

Here are the reasons why the brake pedal is hard to press and the car cannot start: 1. The car's vacuum booster pump is leaking or malfunctioning. The force applied to the brake pedal is amplified by the brake booster pump. If it fails, the brake loses its assist, making it difficult to press. 2. Pressing the brake after the engine is turned off is related to the brake booster pump. The brake booster pump only continuously generates vacuum when the engine is running. When the engine is off, it relies on the remaining vacuum assist, which will restore after restarting and is not a malfunction. 3. In driving, to prevent unexpected situations like sudden movement or rolling when starting the car, automatic transmission models are designed to require pressing the brake to start. If the brake is not pressed, the car cannot successfully start. Additionally, the gear must be in P (Park) or N (Neutral) when starting an automatic transmission car. If starting in N without the handbrake engaged, the car may roll, so the "press brake to start" design is entirely for safety considerations.

12

0

Share

How to Solve the Jerking Issue During Dual-Clutch Transmission Startup?

Here are solutions for addressing jerking during dual-clutch transmission startup: 1. Large difference between engine output speed and transmission output speed: Similar to manual transmissions, dual-clutch transmissions also have a semi-engaged state during power transfer to reduce clutch plate wear. Engineers design the clutch pressure plate and friction disc to engage quickly. If there's a significant speed difference between engine and transmission outputs, jerking may occur. Dry dual-clutch transmissions use mechanical control arms and sleeves to deform diaphragm springs. Structurally, they offer higher transmission efficiency. After optimization with hydraulic systems, they can better filter vibrations, further reducing jerking. 2. Jerking during low-speed gear shifts: Some drivers may notice differences in transmission performance between "cold" and "warm" states at the same speed ranges. This phenomenon isn't unique to dual-clutch transmissions but also occurs in AT and CVT automatic transmissions. 3. Vehicle driving smoothness: Driving smoothness is also related to the engine. Torque response speed is one factor affecting driving feel. Additionally, powertrain mounting design influences the driver's perception of smoothness. Therefore, optimizing powertrain smoothness is a far more complex engineering challenge than one might imagine.

19

1

Share

How to Check if the Radiator Frame Has Been Replaced?

Here are the methods to check if the radiator frame has been replaced: 1. Check for signs of re-grinding on the welding points of the frame. 2. Look for traces of reshaping on the frame. 3. Check if the paint on the frame matches the paint in the engine compartment. 4. Look for signs of repainting or complete repainting. 5. Inspect the side of the car body for any signs of collision repair. Check if the doors fit tightly with the car body, if there is any warping, and if the door gaps are uniform. If repairs or replacements have been made, certain defects will inevitably appear. Below is some related information about the radiator: 1. The radiator is part of the car's cooling system. The radiator in the engine's water cooling system consists of three parts: the inlet chamber, the outlet chamber, the main plate, and the radiator core. The coolant flows inside the radiator core, while air passes outside the radiator core. 2. The hoses of the engine radiator will age over time and are prone to cracking, allowing water to easily enter the radiator. If a hose cracks while driving, the high-temperature water sprayed out can form large clouds of steam escaping from under the engine hood. If this happens, immediately choose a safe place to stop the car and take emergency measures to resolve the issue.

17

2

Share

What items are tested in the C1 License Subject 3 exam?

The C1 license Subject 3 exam includes the following items: vehicle preparation, starting, driving straight, shifting gears, changing lanes, pulling over, going straight through intersections, turning left at intersections, turning right at intersections, crossing pedestrian crossings, passing school zones, passing bus stops, meeting oncoming vehicles, overtaking, making U-turns, and driving at night. According to the "Regulations on the Application and Use of Motor Vehicle Driving Licenses," the scope of vehicles that can be driven with a C1 license includes: small and micro passenger vehicles with a total weight not exceeding 4.5 tons; light and micro cargo vehicles, with the total length of the cargo vehicle not exceeding 6 meters; light, small, and micro special-purpose vehicles; small passenger vehicles with a seating capacity of 9 or fewer people, meaning vehicles with 9 or more seats cannot be driven. A C1 license also allows driving vehicles covered under C2, C3, and C4 license categories. Key points to note for the C1 Subject 3 exam are as follows: Pre-exam preparation: Walk around the vehicle once before getting in and pause near the monitoring area. Light simulation: Check if the light switches are reset before starting the simulation test. Starting: Always observe the surrounding traffic environment before starting. While driving: Keep your gaze straight ahead and avoid following other vehicles too closely. Details on the penalty points for the C1 license Subject 3 exam are as follows: Failing to observe the traffic behind and to the right via the rearview and side mirrors before stopping results in failure. Failing to stop within the specified distance after the examiner gives the instruction to pull over results in failure. If the vehicle body exceeds the right edge of the road or the sidewalk edge after stopping, it results in failure. Failing to observe the side and rear traffic before opening the door after stopping results in failure. Not using or incorrectly using the turn signal before stopping deducts 10 points. Turning the steering wheel less than 3 seconds after activating the turn signal before stopping deducts 10 points. If the vehicle body is more than 30 cm away from the right edge of the road or the sidewalk edge after stopping, it deducts 10 points. Not tightening the parking brake lever after stopping deducts 10 points. Releasing the foot brake before tightening the parking brake lever deducts 10 points. Not turning off the engine before getting out deducts 5 points.

14

2

Share

What material is the suspension of the Hongqi HS5 made of?

The suspension of the Hongqi HS5 is made of aluminum alloy. The front suspension uses a MacPherson independent suspension, while the rear suspension employs a multi-link independent suspension. Both the MacPherson and multi-link suspensions are commonly encountered independent suspension types. The Hongqi HS5 is a mid-size SUV under the Hongqi brand, with a wheelbase of 2870mm and dimensions of 4760mm in length, 1907mm in width, and 1700mm in height. The Hongqi HS5 is equipped with a 2.0-liter turbocharged engine across all variants, delivering a maximum power of 165kW and a peak torque of 340Nm.

17

1

Share

How to Determine if Tires Are Nearing Failure?

Methods to determine if tires are nearing failure include: 1. The tread patterns on the tire surface are almost completely worn out; 2. The tire sidewalls have sustained hard damage due to impacts or other reasons; 3. Sand holes appear on the tire surface, leading to air leakage; 4. Frequent air loss occurs without any identifiable cause; 5. Despite no significant hard damage, the tire has been patched multiple times with excessive trauma. Failing to replace nearly worn-out tires promptly may result in traffic accidents, loss of vehicle control, or breakdowns during driving. Tires are circular elastic rubber products mounted on various vehicles or machinery for ground rolling.

2

3

Share

How to reset the maintenance reminder on the Lavida?

What Causes the Brake Pedal to Be Hard to Press and the Car Unable to Start?

How to Solve the Jerking Issue During Dual-Clutch Transmission Startup?

How to Check if the Radiator Frame Has Been Replaced?

What items are tested in the C1 License Subject 3 exam?

What material is the suspension of the Hongqi HS5 made of?

How to Determine if Tires Are Nearing Failure?

How to Determine if an Engine Has a Misfiring Cylinder?

What is the meaning of a car 4S store?

Where is the diagnostic connector located on the Peugeot 5008?

How to Deal with Rust in the Radiator?