How to reset the maintenance reminder on the Ford Kuga center console?

2 Answers
DelAlexis
07/23/25 11:11pm
Press and hold the reset button "A" while stepping on the brake, and at the same time turn the ignition switch to ON (note: do not start the car). At this point, you should see the display screen flashing or showing the characters "INSP". Continue holding the reset button A without releasing it. Wait until the display shows "..." before releasing the reset button "A". Release the brake and turn the ignition switch back to "OFF" to complete the reset process.
Was this review help?
19
2
Share
DeEliana
08/10/25 7:09pm
I encountered the maintenance reminder light while driving my Ford Kuga and found it quite annoying. A friend told me it can be turned off manually: Insert the key, turn it to the ON position without starting the engine, wait for all dashboard lights to illuminate, then immediately press and hold the OK button on the right side of the steering wheel for about 6 seconds. A setup menu will pop up on the screen—use the directional buttons to navigate to 'Maintenance Info,' select 'Reset Maintenance Reminder,' and confirm. The whole process takes just a minute or two, super convenient. If it doesn’t work, it might be due to an aging battery or loose wiring—check the manual or visit a repair shop. The maintenance reminder is there to prompt timely servicing, so don’t skip oil changes or inspections after turning it off, as regular maintenance extends your car’s lifespan and saves repair costs. A well-maintained car runs smoother and is much safer, especially on long trips.
Was this review help?
18
4
Share
Expand All
More Forum Discussions

What does the complete process of removing the cylinder head of a Roewe 550 look like?

Disconnect all pipelines and wiring connected to the cylinder head, and mark them if necessary to prevent confusion. After the engine has naturally cooled, drain the coolant. When removing the camshaft, follow the sequence of "from both sides to the center" to loosen the camshaft fixing screws to prevent bending deformation of the camshaft.
18
2
Share

How to Switch from S Mode to C Mode in a Mercedes-Benz?

To use the S mode in a Mercedes-Benz, simply move the gear shift lever while the vehicle's engine is running to engage the S mode. Open the driver's side door, press the brake pedal, push the one-touch start button to start the engine, and the dashboard will light up.
5
3
Share

What to Do When the Garage is Blocked?

If the temporarily parked vehicle blocking the garage entrance has the owner's contact information displayed, you can call to discuss the matter with them. If a private garage within the residential area is blocked by a vehicle without contact information or by debris, then call the property management or go directly to the property management office.
17
3
Share

How to Remove the Steering Wheel of a BMW 3 Series?

Release the steering wheel fixing lever, which is the lever that locks the steering wheel in place after adjustment. Pull the steering wheel to its outermost position. Start from the innermost part of the steering column cover, where there is a dust cover (leather), lift the upper cover upwards to remove it. The upper cover is secured with clips, which are very sturdy. After removing the upper cover, you can see that the lower cover is also fixed with clips on both sides. Release the clips and remove the lower cover.
12
1
Share

How to Check the Electronic Oil Dipstick on a Mercedes-Benz C200L?

Press the one-touch start button of the Mercedes-Benz C200 to turn off the engine. Pull the front hood release switch of the Mercedes-Benz C200 to unlock the front hood. Lift up the front hood of the Mercedes-Benz C200. Pull out the oil level dipstick located next to the engine. The oil level of the Mercedes-Benz C200 should be between the upper and lower marks on the dipstick.
12
4
Share

How to Connect Bluetooth in BMW 535?

Turn on the Bluetooth on your phone and also activate the vehicle's Bluetooth, keeping the phone's Bluetooth in a visible state. After enabling the car's Bluetooth, return to the phone's Bluetooth interface and click 'Search for Devices' to locate the car's Bluetooth for pairing. A password is required for pairing. The pairing code will be displayed on the car's system; enter it into your phone and press the pairing button. The car's Bluetooth will automatically connect to the phone upon receiving the correct pairing password. Ensure the password is entered accurately.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.