How to Reset the Maintenance Reminder on Geely Binrui?

1 Answers
LaLaila
07/29/25 1:56pm
Press the menu button on the steering wheel, and corresponding prompts will appear on the dashboard. Use the left and right cycle buttons to switch to vehicle settings; press the middle confirmation button to enter the vehicle settings system. Locate the remaining mileage option, click to enter; select the clear mileage option and confirm.
Was this review help?
10
0
Share
More Forum Discussions

What is the ground clearance of the XT5?

The ground clearance of the XT5 is 175mm. The Cadillac XT5 is a mid-size luxury model positioned by the Cadillac brand, featuring a four-door, five-seat SUV configuration. Its exterior dimensions are 4812mm in length, 1903mm in width, and 1680mm in height, with a wheelbase of 2857mm. The XT5 is equipped with a 2.0T 237-horsepower L4 turbocharged engine and a 9-speed automatic transmission, delivering a maximum power of 174 kW and a maximum torque of 350 Nm. The engine reaches its maximum power at 5000 rpm and its maximum torque between 1500 to 4000 rpm.
6
2
Share

How to Avoid Stalling and Rolling Back on a Hill Start?

Stalling mainly occurs when the clutch is released too quickly, causing the vehicle to roll back. Panicking and either hitting the brakes or releasing the clutch further leads to stalling. The correct way to perform a hill start is to ensure the clutch and brake are fully depressed before starting, then slowly release the clutch. When the vehicle begins to shake noticeably, keep the left foot steady on the clutch pedal without moving it, and gradually release the brake with the right foot.
9
3
Share

What Causes the One-Button Start to Not Respond in a Car?

Reasons why the one-button start in a car does not respond: 1. The steering wheel is locked. When the car is turned off, rotating the steering wheel from the centered position to a certain angle in one direction will lock the steering wheel. In this state, the one-button start function will fail; 2. The smart key battery is dead. The key's transmission power is very low, making it difficult for the car's sensor to detect it, preventing the one-button start from completing the ignition; 3. The gear is not in P (Park). For automatic transmission vehicles, ensure the gear is in the P position before ignition. To unlock the steering wheel, turn it left or right while pressing the engine one-button start button to release the tension.
17
1
Share

How to Prevent Mold When Not Driving for a Long Time?

Keep the car body clean and dry before parking. Carefully check areas prone to water accumulation at the bottom of the car, and remove any accumulated water promptly. Perform maintenance on the car before parking, including changing the oil and three filters. Then disconnect the positive and negative terminals of the battery to prevent it from losing charge. If parking outdoors, always park the car in a relatively elevated location. If it rains, the car could easily become waterlogged. Make sure to park the car on a fairly level surface. Parking on a level surface ensures even stress distribution on all suspensions.
5
0
Share

How to File an Insurance Claim for a Car Scratch?

Call the insurance company's customer service hotline to report the incident, providing a general description of your vehicle's condition. The repair shop will assess the damage and provide a cost estimate. Once both the insurance adjuster and the vehicle owner agree, they will sign to confirm. Gather all necessary documents for the case and submit them to the insurance adjuster to process the claim. After undergoing reviews by various departments within the insurance company, the approved claim amount will be transferred to the vehicle owner's account.
16
4
Share

How to Install Car Wiper Blades?

Lift the cover on top; for some new wiper blades, you can pinch both sides, and the cover will pop open by itself. Then, remove the wiper arm from the wiper. After removing the old wiper blade, gently place the wiper arm on a towel. Be sure not to let it snap back on its own. Remember to remove the rubber protector from the new wiper blade. Open the cover on the new wiper blade, then insert the U-shaped end of the wiper arm into the slot on the wiper. Ensure the U-shaped end is properly seated in the slot. Once installed, close the cover and gently lower the wiper blade into place.
4
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.