How to Reset the Maintenance Reminder on a Polo?

1 Answers
McLillian
07/30/25 4:20am
The method to reset the maintenance reminder on a Polo is as follows: 1. Insert the car key but do not turn it. 2. Press the trip reset button located below the speedometer with moderate force and keep it pressed for the next steps. 3. While holding the reset button, turn the key to the self-check position without starting the engine, still keeping the reset button pressed. 4. Continue holding the reset button for more than 10 seconds, then release it to successfully reset the reminder. Here is some related information: The Polo is a compact car under the SAIC Volkswagen brand, with body dimensions of 3970mm in length, 1682mm in width, and 1462mm in height, and a wheelbase of 2470mm. It is equipped with Volkswagen's high-power version EA211 1.4T turbocharged engine, delivering a maximum power of 150kW and a maximum torque of 250Nm, paired with a 7-speed DSG dual-clutch transmission.
Was this review help?
7
3
Share
More Forum Discussions

What is the ground clearance of the Audi A6 allroad?

Audi A6 allroad's ground clearance can be lowered to a minimum of 140 mm and raised to a maximum of 200 mm. Definition of ground clearance: The vertical distance between the lowest part of the vehicle's chassis and the ground. Ground clearance data reflects the vehicle's ability to pass through complex terrain. Advantages of low ground clearance: Vehicles with low ground clearance have better grip performance. At high speeds, the smaller the distance between the bottom of the car and the ground, the greater the pressure the body receives, which can provide downward force to the body. As a result, the friction between the tires and the ground increases, so even at high speeds, the car's handling can be very good. Differences between high and low ground clearance: Generally speaking, the higher the ground clearance, the better the vehicle's passability, but the stability is relatively poor. If you want to maintain stability while increasing the height of the vehicle, the tires need to have greater grip, which must be achieved by sacrificing fuel consumption. This is also why off-road vehicles have such high fuel consumption. Low ground clearance brings comfort and lower fuel consumption, but if you encounter ditches or bumps, the passability is not as good.
11
4
Share

Does the Toyota Camry use 92 or 95 octane gasoline?

The Toyota Camry uses 92 octane gasoline. The gasoline octane rating only refers to the octane number of the gasoline, representing its anti-knock properties. It has no relation to purity; what truly affects gasoline purity is the collection and transportation process. The higher the octane rating, the more octane it contains, and the better its anti-knock performance. Here are some details about the Toyota Camry: 1. Exterior: The eighth-generation Camry features dual styling designs—Luxury and Sport—both inspired by Toyota's latest "Keen-Look" design language. The Luxury version adopts a large trapezoidal horizontal grille, with a streamlined body posture, lower waistline, and an extended rear roofline that increases rear headroom. 2. Interior: The eighth-generation Camry has undergone significant changes. All three models share the same interior design, differing only in the material of the decorative panels above the glove box and near the gear lever. The interior adopts an asymmetrical design, with a Y-shaped curve on the dashboard. 3. Features: The eighth-generation Camry is equipped with Toyota's latest Toyota Safety Sense, including the Pre-Collision System (PCS), Lane Departure Alert (LDA), Automatic High Beam (AHB), and Dynamic Radar Cruise Control (DRCC), providing enhanced driving assistance for greater safety.
3
1
Share

What are the reasons for brake noise?

Brake noise occurs due to: 1. When the brake discs rub against each other, they generate some metal powder, which can cause unusual sounds when braking. Such noises from the brake pads are normal phenomena; 2. Brake noise may indicate that the brake pads have worn to their limit, causing the brake warning shim to rub against the brake disc, resulting in a metal-on-metal sound. Solutions for brake noise: 1. Firmly pressing the brakes several times or performing emergency stops in an open area can improve the situation; 2. It is necessary to promptly replace the car's brake pads to prevent potential hazards.
18
1
Share

What are the body dimensions of the Audi A5?

Audi A5 body dimensions are: length 4757mm, width 1843mm, height 1358mm, wheelbase 2826mm, fuel tank capacity 54L, luggage compartment capacity 480L, and curb weight 1640kg. Taking the 2021 Audi A5 as an example, it belongs to the midsize car category with a 5-door, 5-seat hatchback body structure. The 2021 Audi A5 features a five-link independent suspension both in the front and rear. It is equipped with a 2.0T turbocharged engine, delivering a maximum horsepower of 204PS, maximum power of 150kW, maximum torque of 320Nm, and is paired with a 7-speed dual-clutch transmission.
7
3
Share

Where is the water temperature gauge located on the MG ZS?

The water temperature gauge of the MG ZS is displayed on the right side of the central instrument panel. To check the water temperature gauge: Step on the brake pedal of the MG ZS, press the one-touch start button, and the instrument panel of the MG ZS will light up, indicating that the vehicle's power is fully connected. Meaning of the water temperature gauge: One mark on the MG ZS water temperature gauge represents 50 degrees Celsius, while four marks indicate the normal operating temperature of 90 degrees Celsius. Function of the water temperature gauge: The car water temperature gauge indicates whether the engine's cooling system is functioning properly. It consists of a pointer, scales, and the letters C and H, where C represents 60 degrees Celsius and the red H mark indicates 110 degrees Celsius. The primary function of the car water temperature gauge is to display the temperature of the coolant in the radiator while the engine is running, with the scale measured in degrees Celsius. When starting the engine, the water temperature gauge should read no lower than 50 degrees Celsius; during normal driving, the normal reading should be between 80-90 degrees Celsius.
1
2
Share

What Are the Reasons for the Vehicle's Engine Malfunction Light Staying On?

The reasons for the vehicle's engine malfunction light staying on are: 1. Sensor damage, poor contact, or signal interruption; 2. Poor engine maintenance; 3. Poor quality of fuel and oil; 4. Incomplete combustion of the air-fuel mixture; 5. Spark plug or ignition coil failure; 6. Fuel pump failure or clogged fuel lines; 7. Clogged air filter. The solutions for the vehicle's engine malfunction light being on are: 1. Use fuel additives to clean the entire fuel system; 2. After cleaning the engine, use higher-grade gasoline; 3. Use high-quality fuel additives to improve the cleanliness level of the fuel; 4. Replace the catalytic converter.
7
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.