How to Reset the Maintenance Reminder Light on Zhonghua Vehicles

1 Answers
SanGage
07/29/25 4:31pm
The method to reset the maintenance reminder light on Zhonghua vehicles is as follows: 1. Insert the key and hold down the small button on the right; 2. Turn the key to the 'on' position without starting the engine; 3. Continue holding the small button for a few seconds before releasing it; 4. Hold the small button again and turn it slightly to the right before releasing to reset the light. Zhonghua is a sub-brand of Brilliance Auto Group. Taking the 2020 Zhonghua V3 Manual Classic as an example, it is a 5-door, 5-seat compact SUV with the following dimensions: length 4240mm, width 1803mm, height 1600mm, and a wheelbase of 2570mm.
Was this review help?
4
3
Share
More Forum Discussions

How to reset the tire pressure light on Volkswagen Magotan?

To reset the tire pressure light on Volkswagen Magotan: 1. Turn on the ignition and press the car button on the infotainment system screen; 2. Click settings, open vehicle settings, and click the tire button; 3. Confirm the tire pressure range, adjust the tire pressure, and drive at a speed of 15 kilometers per hour for ten minutes to automatically reset. Taking the 2020 Volkswagen Magotan as an example, it is a mid-size car with a body size of 4865mm in length, 1832mm in width, 1471mm in height, a wheelbase of 2871mm, a fuel tank capacity of 66 liters, and a trunk capacity of 533 liters.
7
0
Share

Is it necessary to apply film to a sunroof?

It is not necessary to apply film to a sunroof. The sunroof glass usually already has UV protection and heat insulation functions. Applying film again would first result in a certain degree of resource waste and could also have some impact on the overall vehicle quality. The functions of a sunroof are: 1. Release toxic gases inside the car; 2. Prevent exhaust fumes from entering; 3. Reduce the temperature inside the car; 4. Effectively reduce wind noise; 5. Eliminate fogging. The functions of car film are: 1. Block heat generated by infrared rays; 2. Block UV rays to prevent skin damage; 3. Safety and explosion-proof, as the base layer of car film is polyester film, which has tear-resistant and penetration-proof functions; 4. Maintain privacy and security; 5. Reduce air conditioning load; 6. Reduce accidents caused by glare factors.
6
4
Share

Does Brake Fluid Need to Be Replaced?

Brake fluid needs to be replaced, and the replacement method is as follows: 1. Place the vehicle on an inspection pit or lift it with a jack; 2. Clean the drain port, remove the dust cap, loosen the drain screw, repeatedly press the brake pedal until the fluid runs clear, then tighten the drain screw; 3. Add new brake fluid. Characteristics of brake fluid: 1. Very low freezing point: maintains good fluidity in low temperatures; 2. High boiling point: prevents vapor lock under high temperatures; 3. Minimal quality changes: does not cause corrosion to metal or rubber. The function of brake fluid is to transmit hydraulic pressure from the master cylinder to the wheel cylinders, where the pistons, under the action of the seals, push out to apply force on the brake discs and pads, thereby enabling the braking function.
2
2
Share

How long after installing explosion-proof film can you roll down the windows?

After installing explosion-proof film, you can roll down the windows in three days during summer and seven days during winter. Things to note after car window tinting: 1. After installation, wipe the film surface with a wet towel, sponge, or soft cloth; 2. Avoid washing the windows with water for the first three days after tinting to prevent the film from peeling off due to moisture; 3. Try not to use the rear window defogger for the first week, as moisture can also adversely affect the defogger lines. Functions of explosion-proof film: 1. After installation, it can provide heat insulation in summer and save on air conditioning energy; 2. In winter, it can reduce energy loss and maintain interior temperature; 3. It blocks ultraviolet rays; 4. It automatically adjusts interior lighting to suit any weather changes, ensuring clear visibility.
3
0
Share

Where is the reversing radar control unit of Golf VI located?

The reversing radar control unit of Golf VI is located under the interior trim panel on the side of the trunk. The reversing radar mainly consists of ultrasonic sensors, a controller, and a display. When reversing, the reversing radar uses the ultrasonic principle, where the sensors installed on the rear bumper emit ultrasonic waves that reflect off obstacles. The system then calculates the actual distance between the vehicle and the obstacle and provides feedback to the driver, making parking or reversing easier and safer. The Golf VI has dimensions of 4199mm in length, 1786mm in width, and 1479mm in height, with a wheelbase of 2578mm. The car is powered by a 1.6L engine paired with a 7-speed DSG dual-clutch transmission.
3
0
Share

What does 0w40 engine oil mean?

Engine oil 0w40 refers to the oil specification. The 'w' stands for winter use, corresponding to a freezing point of minus 35 degrees Celsius. The number 40 indicates that the oil's kinematic viscosity at 100 degrees Celsius is between 12.5mm2s and 16.3mm2s. A smaller number before the 'w' means better engine protection during cold starts, while a larger number after the 'w' indicates higher viscosity. Engine oil, also known as motor lubricant, serves multiple functions including lubrication, wear reduction, auxiliary cooling, sealing, rust prevention, and shock absorption. It consists of base oil and additives. The base oil is the primary component, determining the fundamental properties of the lubricant, while additives enhance and compensate for any deficiencies in the base oil, providing additional performance characteristics.
6
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.