How to reset the maintenance reminder light on a 408?

1 Answers
McJeffrey
07/29/25 10:28pm
Here are the steps to reset the maintenance reminder light on a Dongfeng Peugeot 408: 1. Locate the maintenance light reset button on the screen and press it. At this point, you'll notice the wrench icon on the dashboard remains illuminated. 2. While holding the button, rotate the ignition key to the ON position. 3. You'll observe the yellow wrench icon disappears, indicating the maintenance light has been reset. Additional information: The maintenance interval for the Dongfeng Peugeot 408 is 7,500 kilometers. The first maintenance service should be performed at 7,500 kilometers and is provided free of charge. The second maintenance, a minor service, should be done at 15,000 kilometers and requires an oil change and oil filter replacement.
Was this review help?
12
2
Share
More Forum Discussions

How Long is the Warranty for BYD New Energy Commercial Vehicles?

BYD new energy vehicles generally come with a whole vehicle warranty of 6 years or 150,000 kilometers, while the battery pack warranty extends up to 8 years or 150,000 kilometers. Additionally, the battery cells are covered by a lifetime warranty service, which is overall superior to other electric vehicle brands in the same category. New energy vehicles refer to automobiles that utilize unconventional vehicle fuels as power sources, integrating advanced technologies in vehicle power control and driving systems to form vehicles with advanced technical principles, new technologies, and novel structures. Below is a detailed introduction to new energy vehicles: 1. Classification: New energy vehicles include pure electric vehicles, extended-range electric vehicles, hybrid electric vehicles, fuel cell electric vehicles, hydrogen engine vehicles, and other new energy vehicles. 2. License Plates: Special license plates for new energy vehicles feature a green background with black characters and black borders. The new energy vehicle license plates are gradient green, while large new energy vehicle license plates are a combination of yellow and green.
19
1
Share

Why is the BMW fan noise particularly loud?

There are many reasons for this issue, such as loud noise when the air conditioning is on, loud noise due to high temperatures, or loud noise caused by damaged components. Below is some relevant information about BMW: 1. Models: BMW is a German automobile manufacturer with a wide range of cars and SUV models. Many BMW models have been locally produced in China, including the 1 Series, 3 Series, 5 Series, X1, X2, X3, and others. The BMW 3 Series is a mid-sized car from BMW, available in both standard wheelbase and long wheelbase versions. 2. Engine: The domestically produced BMW 3 Series models are equipped with three types of engines: a low-power 2.0-liter turbocharged engine, a medium-power 2.0-liter turbocharged engine, and a high-power 2.0-liter turbocharged engine.
5
3
Share

How to Restore Transmission Failure?

Solutions can be determined based on different failures: 1. Automatic transmission oil leakage: Cause of failure: Different models have different leakage locations. The main reason for leakage is poor sealing effect of sealing components, and sometimes it can also be caused by pitting, rust, etc. on the parts. If the leakage is not addressed in time, the transmission will operate with insufficient oil for a long time, leading to further severe internal damage. Repair solution: Overhaul the transmission and replace the sealing components. 2. Vehicle does not move after releasing the brake when in gear: The vehicle can start by accelerating but with noticeable jerking. Cause of failure: Mainly due to pressure leakage in the components responsible for the first gear oil circuit inside the transmission, such as the E1 clutch retaining ring, E1 clutch piston, etc. If this failure is not repaired promptly, it will further damage the transmission's oil pressure solenoid valve, causing severe internal damage to the transmission. Repair solution: Overhaul the transmission and replace the related first gear oil circuit components. 3. Vehicle SPT light and failure light alternately flashing: Cause of failure: The oil pressure solenoid valve is damaged, preventing the transmission from establishing normal working oil pressure (no boost). This failure must be addressed immediately; otherwise, it will cause severe internal burning of the transmission in a short time. Repair solution: Replace the oil pressure solenoid valve.
5
0
Share

What is the tutorial for adding windshield washer fluid to Honda CRV?

crv windshield washer fluid filler port is located at the lower left corner of the engine compartment, with a washer symbol on the cap. Open it to add fluid. The Honda CRV windshield washer fluid capacity is 4L, and it should be added appropriately based on the remaining amount. Windshield washer fluid is only consumed when used, so there is no fixed refill interval; it should be refilled when low. Below are related instructions: 1. Adding detergent: In summer when there is more dust, you can add slightly more detergent, about one capful. Be careful not to use too much, as excessive detergent can leave the windshield unclean. 2. Adding alcohol: In winter when temperatures are colder, the freezing point can be lowered by adding an appropriate amount of alcohol. A mixture of 40-50% alcohol and 50-60% water can achieve a freezing point of -25°C, which meets the needs of most regions across the country.
13
3
Share

What to do if there is a sound of metal scraping the ground when the car is running?

Prompt inspection and repair are necessary. Below are the reasons for abnormal noises in cars and their solutions: 1. Brake noise: The brake is a very important part of the car and also a frequently used component. Over time, various issues may arise, leading to different sounds. Common causes of such noises include: excessive iron content in the brake pads, worn-out brake pads reaching their limit, or foreign objects on the brake disc. Solution: The owner can replace the brake pads with new ones. 2. Tire noise: Tires are the most severely worn part during driving. Over time, tires may produce abnormal noises, and the frequency of these noises increases with the car's speed. Generally, when the owner hears such sounds, it indicates a problem with the car's tires. Solution: The owner should stop and carefully inspect the tires, trying to remove any foreign objects. Otherwise, prolonged driving with such issues can cause severe wear to the tires. 3. Bearing noise: During driving, due to road conditions and other factors, pressure bearings often crack or get damaged, leading to a "clunking" sound from the front when driving on bumpy roads. In severe cases, this can cause wheel misalignment. Aging bearings can also produce abnormal noises. If a "humming" sound is heard while driving, it usually indicates a problem with the bearings, and the noise tends to worsen as the car's speed increases. Solution: The owner should promptly visit a nearby repair shop for maintenance and replace the wheel hub bearings in time.
3
1
Share

How to Deal with the DPF Light in Diesel Vehicles?

The DPF light in diesel vehicles indicates the particulate filter warning light. The specific handling methods are as follows: 1. Automatic Regeneration: When the DPF light is green, no intervention is needed. At this time, the vehicle is generally driving at high speed (above 80km/h). Keep the vehicle in normal driving state, and the DPF indicator light will automatically turn off after the particulate matter is processed. 2. Manual Regeneration: When the DPF light is yellow, you should leave the lane in time. After the vehicle is turned off, press the DPF light control button. At this time, the yellow indicator light will stay on, and the processing time is about 15-30 minutes. After the particulate matter is processed, the indicator light will automatically turn off. 3. Random Regeneration: It can be operated at any time. After the vehicle is parked, press and hold the DPF processing button for 3-5 seconds to start the detection and processing. If the yellow indicator light flashes, it means manual regeneration is required, and you need to press the DPF button again; if the yellow indicator light stays on, wait for 15-30 minutes. When the indicator light turns off, it means the particulate matter processing is completed.
1
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.