How to reset the maintenance reminder for the 2020 Geely Vision X6?

What's the reason for difficulty starting both when the engine is hot and cold?

The reasons for difficulty starting both when the engine is hot and cold are as follows: 1. Excessive carbon deposits: This indicates severe carbon buildup in the car, requiring inspection of the engine's throttle valve and spark plugs, with replacement if necessary. 2. Residual fuel pressure in the fuel system is too low: Clamp the return fuel line and check the fuel pressure. If the pressure can be maintained for a period, it indicates a malfunctioning fuel pressure regulator, leading to excessively low residual fuel pressure and causing starting difficulties. If clamping the return fuel line still cannot maintain the pressure, it indicates a faulty electric fuel pump, resulting in insufficient fuel pressure.

10

2

Share

What are the signs of a motorcycle running low on engine oil?

When a motorcycle runs out of engine oil, the following phenomena will occur: Severe wear of components due to lack of lubrication will happen in a very short time, eventually causing the engine cylinder, piston, rings, and crankshaft to seize and stop functioning. Key characteristics of engine oil: The engine is the heart of a vehicle, containing many metal surfaces that rub against each other. These components operate at high speeds, in harsh environments, and can reach temperatures between 400°C to 600°C. PurePlus Technology: The new PurePlus technology converts natural gas into crystal-clear, fully synthetic base oil. Combined with exclusive power cleaning technology, it creates lubricants with superior cleaning and protective performance. Under such extreme conditions, only qualified lubricants can reduce engine component wear and extend service life.

20

3

Share

What is the Difference Between Original and Genuine Auto Parts?

Auto parts can be categorized as original or genuine, with the following differences: 1. Definition: Original parts: These are produced by the official suppliers of the vehicle manufacturer. Genuine parts: These are manufactured directly by the original manufacturer, not outsourced or assembled by other authorized manufacturers. 2. Production differences: Original parts: These are not made by the vehicle manufacturer itself but by the same production suppliers as the original parts, also sold in the market, including branded parts and imitations. Genuine parts: Some manufacturers with inadequate production technology are continuously commissioned by well-known brands to produce parts, either as OEM or joint ventures, making it difficult to distinguish genuine from fake in the market.

6

2

Share

How to Properly Jump Start a Car?

Correct method for jump starting a car: 1. Connect the red clamp to the positive terminal of the dead battery, then connect the other end of the red cable to the positive terminal of the booster car; 2. Connect the black clamp to the negative terminal of the booster car, then connect the other end of the black cable to the negative terminal of the dead battery or a suitable grounding point. Precautions for jump starting: 1. Keep the booster car running, and start the dead car normally after completing the jump start procedure; 2. When possible, it's recommended to let the revived car run for more than half an hour to ensure sufficient charging; 3. Avoid contact between positive and negative terminals and ensure correct polarity connection during jump starting.

10

0

Share

What maintenance items should be done for a family sedan at 60,000 kilometers?

The thermostat of the Magotan is located inside the plastic pipe at the interface of the upper and lower water pipes, and it is integrated. Working principle of the thermostat: The thermostat automatically adjusts the amount of water entering the radiator based on the temperature of the coolant, changing the circulation range of the water to regulate the heat dissipation capacity of the cooler and ensure the engine operates within the appropriate temperature range. The thermostat must be kept in good technical condition; otherwise, it will seriously affect the normal operation of the engine. Too late and too early: If the main valve of the thermostat opens too late, it will cause the engine to overheat; if the main valve opens too early, it will prolong the engine warm-up time, causing the engine temperature to be too low.

3

4

Share

What Causes Noise in the Steering Gear?

Reasons for noise in the steering gear: Lack of Lubrication: If there is a lack of lubrication in the screws inside the steering wheel, you need to remove the steering wheel cover and add lubricating oil. This should allow smooth movement in the track and pivot areas. Steering Gear Malfunction: The steering gear might also malfunction. Normally, if the steering wheel is turned too sharply while turning, it puts a greater load on the steering gear, leading to severe wear and resulting in abnormal noises. It is recommended to inspect and replace the faulty components. Insufficient Tire Pressure: Uneven tire pressure in the left front or right front tire can cause the car to pull to one side, leading to unbalanced wheel bearings, misaligned steering gear, and resulting in abnormal noises and pulling.

14

5

Share

How to reset the maintenance reminder for the 2020 Geely Vision X6?

What's the reason for difficulty starting both when the engine is hot and cold?

What are the signs of a motorcycle running low on engine oil?

What is the Difference Between Original and Genuine Auto Parts?

How to Properly Jump Start a Car?

What maintenance items should be done for a family sedan at 60,000 kilometers?

What Causes Noise in the Steering Gear?

How Many Chips Are There in a Car?

Where is the child lock on the Chevrolet Cavalier?

Is the Invoice Amount Important for Used Cars?

How to Push-Start a Car?