How to reset the maintenance reminder for Ford Escort?

What is the principle of an automotive electronic regulator?

The principle of an automotive electronic regulator is: When the engine's output voltage is too low or fails due to other reasons, the battery will generate a current in the generator's windings (known as reverse current). The electronic regulator cuts off this reverse current to prevent over-discharge of the battery, which could damage the battery, and to avoid excessive current flowing into the generator windings, which could damage the generator. The regulator consists of three relays: one is responsible for adjusting the generator's output voltage, another for preventing excessive charging current. When the charging current is too high, the circuit activates both the voltage regulation relay and the current limiting relay simultaneously, disconnecting the generator's excitation circuit and stopping the generator. The third relay is responsible for cutting off the charging circuit when reverse current occurs, activating to disconnect the charging circuit in such cases.

12

5

Share

Should You Power On First or Plug In First When Charging a New Energy Vehicle?

When charging, power on first, then plug in the charging gun. When disconnecting, unplug the charging gun first, then power off. Here is some relevant information about new energy vehicles: 1. Recommendations: The number of charge/discharge cycles has no direct impact on the lifespan of the power battery. The battery itself has no memory function. In principle, it is recommended that customers charge and discharge promptly, as timely charging and discharging can maintain the battery's good charge/discharge capability. 2. Winter Usage Tips: Charging immediately after use in winter ensures the power battery remains at a relatively high temperature, avoiding the heating phase during charging and effectively reducing charging time. If the current range does not affect normal travel, it is also acceptable to perform a charge/discharge cycle every 3-5 days on average.

11

3

Share

What are the three components of a mechanical steering system?

The three components that make up a mechanical steering system are the steering control mechanism, the steering gear, and the steering linkage. The specific components include: 1. Power steering gear. 2. Steering transmission pair. 3. Steering pitman arm. 4. Steering longitudinal rod. 5. Steering tie rod. 6. Steering knuckle arm. Information about the mechanical hydraulic power steering system is as follows: 1. Mechanical hydraulic power steering system: This is an economical power steering system, generally composed of components such as a hydraulic pump, oil pipes, pressure flow control valve body, V-belt, and oil reservoir. 2. Classification: Rack and pinion steering gear type hydraulic power steering system, worm and sector steering gear type hydraulic power steering system, and recirculating ball steering gear type hydraulic power steering system.

18

5

Share

What Lights to Turn On When Driving at Night?

When driving at night, turn on the width marker lights and low beams. If the illumination is insufficient or there are few oncoming vehicles, you may also use high beams. However, it is important to note that when encountering oncoming traffic, you should switch from high beams to low beams to avoid affecting the visibility of the oncoming vehicles and creating safety hazards. When driving at night at speeds below 30 kilometers per hour, use low beams, with the light projecting more than 30 meters ahead. At speeds above 30 kilometers per hour, use high beams, with the light projecting more than 100 meters ahead. When driving on roads with streetlights, you may use anti-glare lights or low beams and width marker lights.

15

5

Share

How to Start a Car Correctly?

Correct steps to start a car: 1. Insert the key into the Lock position without turning it immediately, wait for about 2 seconds; 2. Turn the key directly through the ACC position and stop at the ON position, waiting for about 5 seconds; 3. Turn the key to the START position to ignite, the ignition time should not be too long, it is recommended not to exceed 3 seconds, release the key immediately after hearing the car engine start, allowing the key to automatically return to the ON position; 4. Do not operate immediately after the engine starts, wait for about 30 seconds for the engine to warm up; 5. Press the foot brake, shift the gear to D, release the handbrake, then slowly release the foot brake, and the car starting process is completed.

12

3

Share

What is the use of a VIN number?

VIN is the vehicle identification code on the driving license, equivalent to a person's ID card. Knowing the VIN allows you to check vehicle maintenance records and traffic violation information online. Here is more information about VIN: 1. A VIN is a unique set of seventeen letters or numbers used on vehicles to identify the manufacturer, engine, chassis number, and other specifications. To avoid confusion with numbers 1, 0, and 9, the letters "I", "O", and "Q" are not used. The 10th digit representing the model year does not use "I", "O", "Q", "U", "Z", or "0". 2. Through permutation and combination, the VIN ensures that no two vehicles of the same model will have the same number within 30 years.

10

5

Share

How to reset the maintenance reminder for Ford Escort?

What is the principle of an automotive electronic regulator?

Should You Power On First or Plug In First When Charging a New Energy Vehicle?

What are the three components of a mechanical steering system?

What Lights to Turn On When Driving at Night?

How to Start a Car Correctly?

What is the use of a VIN number?

Why is there no production date on the tire?

What is the reason for the exhaust system warning light in the Magotan?

How many days after booking can I take the Subject 4 exam?

What does the DEF light on Jiangling Motors mean?