How to reset the maintenance reminder for Changan CS75?

1 Answers
DanteLynn
07/24/25 5:52am
Here is the method to reset the maintenance light for Changan CS75: 1. Turn the car key to the ON position (full power-on state), then press the selection button on the left side of the steering wheel. 2. Hold the reset button for about 5 seconds. 3. Turn off the vehicle power, keeping the reset button pressed, then turn the power back on. 4. The maintenance reminder reset is successful. Here are some related specifications: Taking the 2021 Changan CS75 as an example, it is a compact SUV with a body length of 4650mm, width of 1850mm, height of 1715mm, a wheelbase of 2700mm, a fuel tank capacity of 58 liters, and a trunk capacity of 520 liters.
Was this review help?
17
2
Share
More Forum Discussions

Where is the steering wheel heating switch on the Envision?

The steering wheel heating switch on the Envision is located in the left-hand control area of the multi-function steering wheel. Taking the 2021 Envision as an example, it is a mid-size SUV with body dimensions of 4694mm in length, 1839mm in width, 1686mm in height, a wheelbase of 2750mm, and a curb weight of 1610kg. The 2021 Envision features a MacPherson strut front suspension and a multi-link independent rear suspension. It is equipped with a 1.5T turbocharged engine, delivering a maximum horsepower of 169PS, a maximum torque of 250Nm, and a maximum power of 124kW.
20
1
Share

Can You Still Drive When the Oil Dipstick is at the Lower Limit?

You can still drive when the oil dipstick is at the lower limit. Generally, there is approximately one liter of capacity between the upper and lower limits on the dipstick. Even when the oil level reaches the lower limit, the lubrication function of the oil is still sufficient. Under these circumstances, the car can still be used normally, but aggressive driving or high-load usage is not recommended. If you drive aggressively at this point, it can cause excessive engine load and increased temperature, potentially leading to engine overheating. Engine oil, or motor oil, plays crucial roles in the engine, including lubrication, cleaning, cooling, sealing, reducing wear, damping vibrations, and preventing rust and corrosion. Currently, there are three types of engine oil on the market: conventional mineral oil, semi-synthetic oil, and full-synthetic oil.
20
4
Share

What are the effects of a bad ball joint in a car?

The effects of a bad ball joint in a car include: 1. Producing a knocking noise when driving on bumpy roads; 2. A damaged ball joint can cause slight displacement in the suspension, leading to errors in wheel alignment data, which may result in uneven tire wear and steering deviation; 3. During braking, a loose ball joint can cause uneven braking force on both sides, leading to steering deviation when applying the brakes. Composition of the car chassis: It consists of the transmission system, steering system, running system, and braking system. Methods for maintaining the car chassis: 1. Regularly inspect the condition of important assemblies; 2. Monitor the wear of brake pads and clutch plates; 3. Perform wheel alignment periodically; 4. Pay attention to tire pressure and wear conditions.
8
3
Share

What is the reason for the steering wheel exclamation mark preventing startup?

The reason for the steering wheel exclamation mark preventing startup is: There is a fault in the active steering system that requires inspection and repair. The correct steps to start a car are: 1. Start the car; 2. Shift the gear into N position; 3. Press the electronic handbrake; 4. Switch the gear to D position; 5. Step on the accelerator. The reasons for a car failing to start are: 1. Fuel supply system issues, such as clogged low-pressure fuel lines, loose pipes causing fuel leakage, air in high-pressure fuel lines, poor technical condition of injectors, incorrect injection timing angle; 2. Insufficient air intake, clogged air filter element; 3. Insufficient cylinder compression pressure, damaged cylinder gasket causing air leakage, valves not closing tightly causing air leakage, worn piston cylinder causing air leakage; 4. Starting device issues, such as power supply failure, poor contact of the electromagnetic switch, poor contact between the starter motor commutator and brushes, clutch slippage in the starter transmission mechanism.
18
0
Share

How to Turn on the Heating in a BMW 525?

The method to turn on the heating in a BMW 525 is as follows: 1. Start the car and properly warm up the engine; 2. Turn off the AC snowflake button; 3. Wait until the water temperature rises to the normal operating temperature; 4. Turn the knob to the red zone to activate the heating mode. Taking the 2021 BMW 525 as an example, it belongs to the mid-to-large-sized car category with the following dimensions: length 5106mm, width 1868mm, height 1500mm, wheelbase 3105mm, fuel tank capacity 68 liters, and curb weight 1705kg. The 2021 BMW 525 features a double-wishbone independent front suspension and a multi-link independent rear suspension. It is equipped with a 2.0L turbocharged engine producing a maximum horsepower of 184PS, maximum power of 135kW, and maximum torque of 290Nm, paired with an 8-speed automatic transmission.
13
3
Share

What is the bulb model for Mazda CX4?

Mazda CX4 uses H4 bulbs, with additional details as follows: Common headlight bulb models: Different vehicles may use different headlight bulb models. Common models include H1, H3, H4, H7, and H11. Among current mainstream vehicle models, H3 and H11 bulbs are primarily used for fog lights, while H4 bulbs are commonly found in Korean and Japanese vehicles where high and low beams are integrated into a single bulb. H1 and H7 bulbs are predominantly used in European vehicles for high and low beam functions. Automotive headlight introduction: Automotive headlights, also referred to as vehicle headlamps or LED daytime running lights, serve as the "eyes" of a car. They not only contribute to the owner's external image but are also crucial for safe driving during nighttime or adverse weather conditions. Headlight boosters: Headlight boosters employ scientific voltage regulation to provide optimal and stable working voltage specifically for vehicle headlights. They feature a 3-6 second preheating protection for bulb filaments during startup. Once activated, the headlights emit consistent, bright white light unaffected by engine RPM fluctuations. These devices maintain the original headlight beam pattern without increasing electrical load on the vehicle's wiring system, offering safe and practical installation with extreme simplicity.
12
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.