How to reset the maintenance light on the Zhonghua V3?

1 Answers
DeCassandra
07/29/25 4:31pm
To reset the maintenance light on the Zhonghua V3: 1. Turn off the vehicle's ignition button; 2. Press and hold the maintenance reset button on the instrument panel for an extended period; 3. While continuing to hold the maintenance reset button, press the vehicle's start button to power on the car; 4. Release the maintenance reset button when the display shows 0000.0. The Zhonghua V3 is a 5-door, 5-seater compact SUV with dimensions of 4240mm in length, 1803mm in width, 1600mm in height, and a wheelbase of 2570mm. It is equipped with a 1.6L naturally aspirated engine delivering a maximum power of 87kW and peak torque of 150Nm.
Was this review help?
3
3
Share
More Forum Discussions

How to Start the Vehicle When the Civic Key Fob Battery is Dead?

Open the mechanical key on the side of the remote key fob and use it to unlock the car door. Once inside the vehicle, place the remote key fob against the push-button start, and the car will start.
2
4
Share

What materials are used to make car brake pads?

Car brake pads are made of the following materials: 1. Resin-based brake materials; 2. Powder metallurgy brake materials; 3. Carbon-carbon composite brake materials; 4. Ceramic-based brake materials. The function of brakes is to reduce speed or bring the vehicle to a stop. Their working principle involves converting the kinetic energy of the moving vehicle into frictional heat energy through the friction between the brake pads and brake drums, as well as between the tires and the ground, thereby slowing down or stopping the vehicle. Reasons for brake failure include: 1. Impurities in the master cylinder or poor sealing; 2. Failure of the vacuum booster pump; 3. Dirty brake fluid; 4. Oil leakage from the master cylinder or wheel cylinder; 5. Air leakage from the air reservoir or pipeline connections; 6. Severe overloading; 7. Carbonization of the brake drum; 8. Insufficient brake fluid in the master cylinder; 9. Wear of the master cylinder piston.
1
5
Share

Why is the engine very hot but the water temperature is normal?

Reasons for the engine being very hot while the water temperature is normal: 1. Insufficient engine coolant; 2. Faulty water temperature sensor or gauge; 3. Driving with tailwind or prolonged low-speed high-load driving in hot seasons; 4. Ignition timing too early or too late; 5. The louver cannot fully open; 6. Overly lean or rich air-fuel mixture; 7. Severe dirt on the exterior or scale buildup inside the radiator, leading to poor heat dissipation, necessitating radiator cleaning or replacement. When the car engine radiator temperature is too high, you should pull over to a safe area, set up a warning sign, open the engine hood, turn off the engine, and then wait for a period until the engine's water temperature has sufficiently dropped before checking the engine's coolant level.
9
0
Share

How to Solve the Problem of a Scooter Not Starting?

Scooter still won't start even with electricity and fuel, the most likely reason is a problem with the ignition device. Sometimes, wiring issues can also cause the scooter not to start. If the cause is unknown, we can try kick-starting.
5
2
Share

How to Measure a Four-Wire Idle Speed Motor?

Four-wire idle speed motor measurement method: You can use the resistance range of a multimeter to measure the resistance of the four pins separately. The resistance of the coils is generally several tens of ohms. If the measured resistance values of the two sets of coils are similar, it indicates that the idle speed motor is functioning properly. The idle speed motor, also known as a stepper motor, commonly comes in three-wire, four-wire, and six-wire configurations, with four-wire being the most common. It has two sets of coils, with the four wires connecting to the ECU and power supply, respectively. None of them should be grounded, as this could damage the ECU. The idle speed motor is used to control the idle speed of the car. If it malfunctions or is damaged, it can affect the idle operation of the car's engine, leading to issues such as difficulty starting, unstable idle speed, idle shaking, stalling at idle, or slow acceleration. Timely inspection, repair, or replacement is necessary.
2
5
Share

What Car Modifications Are Legal?

Car modifications can include changes to wheel styles, roof racks and side steps, body color, grilles, and front/rear bumpers. Wheel styles can be altered: New regulations have relaxed rules on wheel modifications. As long as the wheel size and specifications match those on the vehicle registration certificate, the style can be changed—even if all four wheels have different designs. Roof racks and side steps can be installed: This new rule mainly applies to SUV and MPV models. The height of the roof rack must be within 300mm, and the width of the side steps must not exceed 5cm beyond the vehicle's side profile. Body color can be changed: Whether through painting or wrapping, the body color can be modified. However, the vehicle information must be updated with the DMV within 10 days. Note that colors resembling those of emergency vehicles, such as police cars or fire trucks, are prohibited. Grilles and front/rear bumpers: The styles of grilles and bumpers can also be modified. However, the new grille and bumper must not alter the original vehicle length or width. The car emblem cannot be changed, and the bumper must not have any prominent protrusions, such as tow hooks (commonly known as "tow hitch hooks"), which are not allowed.
11
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.