How to Reset the Maintenance Light on the Tayron?

[DelIsabella]

Tayron maintenance light reset method: While pressing the maintenance button, turn the ignition key to the light-on position. After hearing a beep, release the maintenance button, wait for two seconds, then press and hold the minute button next to the instrument panel. Check if the maintenance light has been cleared. If it has, the reset was successful; otherwise, repeat the above two steps. The original purpose of the car maintenance light is to remind the owner to perform maintenance as soon as possible. After maintenance is completed, the 4S shop will use a fault diagnostic tool to reset the vehicle's maintenance light. The Tayron has a length, width, and height of 4589mm, 1860mm, and 1660mm respectively, with a wheelbase of 2731mm. In terms of configuration, in addition to conventional features such as a 360-degree panoramic image, third-generation intelligent parking assist system, and blind spot detection, this vehicle is also equipped with a traffic jam assist system.

[McRobert]

I've been driving for over a decade and have manually reset the maintenance light several times. It's not difficult. First, make sure the car is turned off. Press and hold the 0.0 button on the dashboard without releasing it, then turn the key to the 'on' position without starting the engine. At this point, a reset prompt will appear on the screen. Release the button and press it once more to confirm. Finally, when you see the next maintenance mileage displayed, you've succeeded. During the operation, make sure to press the button all the way down and don't release it midway. If the display doesn't respond, check if the battery voltage is normal. After resetting, it's recommended to start the engine to see if the warning light is still on. The most crucial part of the whole process is timing control – pressing too fast or too slow won't work. Remember, this method is only suitable after completing maintenance; don't reset the light before maintenance. If you really can't manage it, just let the repair shop use a computer to reset it – much easier.

[VanSabrina]

Last time my maintenance light came on, I went to the service center and the technician taught me a simple method: With the engine off, hold down the 0.0 button on the dashboard, then turn the ignition to the position where the dashboard powers on. When the maintenance reminder appears on the screen, release the button and immediately press it once more to confirm the reset. After completion, the system will display the new maintenance interval. Remember to complete the confirmation action within ten seconds of powering on; if it exceeds this time, you'll need to start over. Different model years may have variations in the prompt text, but the basic logic of the operation remains the same. If you try three or four times without success, it might be a circuit issue or poor button contact. In such cases, it's better not to force it and instead visit the shop to clear it with a diagnostic tool for safety. Trying to fix it yourself might mess up the maintenance records.

[LaValeria]

As someone who frequently deals with cars, the key to resetting the maintenance light on the Tayron lies in precise timing. After the vehicle is completely turned off, use your fingertip to press and hold the 0.0 reset button, then turn the key to the ignition-on position. When the screen flashes the inquiry interface, immediately release and lightly tap the button to confirm—the entire sequence must be completed within seven to eight seconds. Most reset failures occur due to misaligned step intervals or abnormal maintenance cycle data. For new cars, it may take driving about 50 kilometers after resetting before the prompt updates. A special reminder: ensure the vehicle is parked on level ground with the handbrake engaged when performing this operation—avoid doing it on slopes. If the infotainment system is a third-generation version, power cycling before retrying yields better results.

[VonLouis]

DIY reset is actually quite simple, I just did it for my Tayron. Fully turn off the car, hold the small SET button on the instrument panel with your right hand, then turn the key to power on until the dashboard lights up. Release the right hand when the service menu pops up on the screen, then press that button to confirm. The whole process is as quick as restarting a phone. If the center screen remains black, it means it's not properly positioned. A successful reset will be accompanied by a 'ding' sound, and the wrench icon on the dashboard will disappear. If the last maintenance was done outside, it's best to take a photo of the mileage before resetting to avoid disputes with the dealership next time. If you really can't manage, you can also remotely schedule a code clearing via the Volkswagen app on your phone.

[ClaraMarie]

To reset the maintenance light on the Tayron, I've used this method: After turning off the engine, press and hold the 0.0 button on the lower right of the steering wheel. Turn the key to the ignition-on position without stepping on the brake. Wait until the digital dashboard displays an English prompt, then release the button and lightly press the confirmation key. The reset will be signaled by the headlights flashing twice. The key is to maintain firm pressure at the moment of ignition—white-knuckle intensity is necessary. For older models with a rotating gear icon on the dashboard, first switch to the maintenance page before proceeding. If the mileage display appears abnormal after resetting, it's recommended to disconnect the battery for three minutes to reboot the system. This method is suitable for regular maintenance; if the engine fault light is on, the fault must be addressed first. By the way, it's best to reset the light yourself after the first service on a new car to save a trip to the dealership.