How to reset the maintenance light on the Great Wall H2s?

1 Answers
CarolineFitz
07/25/25 8:01am
Great Wall H2s maintenance light reset method: 1. Turn on the ignition switch and press the CLR button on the right side of the driver information center display; 2. Confirm the engine oil change information, clear the information on the display and reset it, then the maintenance light can be reset. The Great Wall H2s has body dimensions of 4146mm in length, 1772mm in width, and 1638mm in height, with a wheelbase of 2550mm. Compared to similar models, the Haval H2s is relatively small. It is equipped with a 1.5T turbocharged engine, paired with a 6-speed manual or 7-speed dual-clutch transmission, delivering a maximum horsepower of 159.
Was this review help?
3
3
Share
More Forum Discussions

Is a Purchased Driver's License the Same as One Obtained Through Examination?

Purchased driver's licenses are not the same as those obtained through proper examination. Below are the relevant penalties regarding driver's licenses: 1. Revocation of License: If an applicant obtains a motor vehicle driver's license through fraudulent means such as deception or bribery, the traffic management department of the public security authority will confiscate the license and revoke the driving permit; the applicant will be barred from reapplying for a driver's license for three years. 2. Fines: Those who use forged or altered motor vehicle driver's licenses will have their licenses confiscated by the traffic management department of the public security authority, be detained in accordance with the law, and fined between 2,000 and 5,000 yuan; if the act constitutes a crime, criminal liability will be pursued according to the law.
7
4
Share

What brand is the engine of Li Auto?

Li Auto is a pure intelligent electric vehicle brand, whose concept is to create intelligent electric vehicles without range anxiety for users. The following is the relevant introduction about Li Auto: Introduction: Li Auto has certain guarantees in production quality. By acquiring Lifan Auto to obtain passenger car manufacturing qualifications, Li Auto has its own Changzhou manufacturing plant to produce Li Auto vehicles. The factory uses a large number of internationally advanced equipment and has fully automated production lines. Therefore, consumers do not need to have significant concerns about production. Range: In terms of range, unlike pure electric vehicles, Li Auto can eliminate range anxiety through extended-range technology. According to Li Auto's official data, Li Auto can achieve a range of 800 kilometers under NEDC comprehensive conditions, and the urban range may exceed 1,000 kilometers.
20
5
Share

Does starting the car and air conditioner simultaneously affect the vehicle?

Starting the car and air conditioner simultaneously has minimal impact on the vehicle. When the air conditioner is turned on at idle speed, the engine load increases, but the engine automatically raises its RPM to maintain normal operation, resulting in slightly higher fuel consumption. Here are some fuel-saving tips for vehicles: 1. Maintain a steady speed: Control your speed while driving and avoid sudden braking. 2. Avoid opening windows at high speeds: Driving with windows open at high speeds increases fuel consumption. 3. Regularly check tire pressure: Ensure proper tire inflation, as both underinflation and overinflation can increase fuel consumption. 4. Pay attention to transmission maintenance: Always use the correct transmission fluid for your vehicle, as it not only lubricates but also transmits torque, so regular replacement is necessary.
6
0
Share

Where is the cabin air filter located in the Mazda CX-4?

Mazda CX-4's cabin air filter is located inside the glove compartment on the passenger side. Some models have two filters, with the additional one positioned under the lower edge of the front windshield. Below are the steps for replacing the cabin air filter: 1. First, locate the glove compartment cover panel, where the fixing clips are installed. 2. After removing the fixing devices, the cover panel can be easily taken off. 3. The cabin air filter is housed in the air filter box. Simply press the clips on the air filter box cover to remove it. 4. The cabin air filter will then be exposed. Grip one end of the filter and gently pull it out. 5. If the filter is excessively dirty, replacement is necessary. If there's minimal dust, tapping it clean may allow for continued use. 6. During installation, ensure the text on the filter faces the driver. Installing it backwards will render it ineffective.
16
0
Share

What does a car with a 260 speedometer indicate?

This pertains to the design of the dial, as most cars can only reach just over 200. Additional knowledge is as follows: 1. Cars with a 260 speedometer: There are many models with a 260 mph speedometer on the dashboard, such as the Volkswagen Magotan, BMW 3 Series, Mercedes-Benz C-Class, Volvo V60, etc. Cars with a 260 mph speedometer are mostly luxury vehicles from brands like BMW, Mercedes-Benz, Audi, Porsche, Ferrari, Lamborghini, Rolls-Royce, and Bentley. 2. Maximum speed: Achieving a speed of 260 on the speedometer means that, with speed limits removed, these models can reach a maximum speed of 260. Therefore, vehicles with a displacement of 2.0 or less than 3.0 can hardly reach this speed, and only a portion of them can, which are not cheap.
15
5
Share

What are the wheels that slide called?

The wheels that slide are called floating wheels. Here are the specific details about the wheels: 1. Principle: Floating wheels use a principle similar to that of a roly-poly toy. Floating wheels employ an additional bearing on the wheel hub, which can move around the central axis. When the wheel is in motion, this bearing keeps the wheel hub in a floating state. Additionally, floating wheels are appropriately weighted to maintain stability during driving. 2. Precautions: Pay attention to early warning signs of bearing wear, including any friction noise during rotation or abnormal deceleration of the wheel assembly when turning. For rear-wheel-drive vehicles, it is recommended to lubricate the front wheel hub bearings when the vehicle reaches 38,000 kilometers. When replacing the braking system, inspect the bearings and replace the oil seals. If you hear noise from the wheel bearing area, the first step is to identify the source of the noise.
2
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.