How to reset the maintenance light on the 2020 Geely Emgrand GS?

[VonEli]

Ignition switch: With the ignition switch turned off, press and hold the trip reset button without releasing, insert the car key and turn it to the position where the instrument lights come on, then release the trip reset button and wait for the maintenance light to go off. Instrument panel: There is a button on the instrument panel used to adjust the trip odometer. Press and hold this button for 2-3 seconds while the engine is idling; once the maintenance reminder turns off, the maintenance reset is complete. Mode button: Turn off the ignition switch; simultaneously press and hold both arrow buttons, then turn on the ignition switch; after the ignition switch has been on for about 3 seconds, release both arrow buttons; the display will then show the maintenance menu, asking if you want to reset; press and hold the SET (reset) button for more than 3 seconds; press the MODE button; turn off the ignition switch to complete the reset.

[Rod]

As an owner who has driven the 2020 Emgrand GS, I've tried resetting the maintenance light a few times, and it's quite simple. First, sit in the driver's seat and turn the key to the ON position, which means the dashboard lights up but the engine doesn't start. Then, look at the dashboard—there's a button, usually marked with a small dot in the lower right corner, responsible for mileage reset. Press and hold that button for about 5 to 10 seconds, and you'll see the maintenance light start to flash and then turn off. Once done, just turn off the key. I recommend doing this immediately after each maintenance service. After resetting, it starts counting down to the next maintenance time. If you don't reset it, the light stays on, which might cause you to miss actual repair signals, and you can also save some money by avoiding unnecessary trips to the 4S store. Pay attention to regular vehicle maintenance—change the oil every 5,000 kilometers to ensure the engine stays healthy.

[LeilaniLynn]

The key to the maintenance light reset process lies in the button operation. Start the car to the ON position but do not ignite the engine. When the dashboard lights up, locate the reset button, which might be near the left side of the steering wheel. Press and hold it firmly for a few seconds until the indicator light goes off. If the light doesn't respond, don't panic—it might be due to incorrect button placement; check the manual for confirmation. Remember, resetting ensures more accurate next maintenance, preventing overdue oil changes due to misleading lights. This car has low maintenance costs, and doing it yourself saves time and money while learning basic car repair skills. Develop a habit of keeping records for better vehicle condition and peace of mind while driving.

[LaylaDella]

Resetting the maintenance light for the 2020 Emgrand GS: Step 1, turn the key to ON without starting the engine. Step 2, press and hold the dashboard button (such as the trip reset button) for several seconds until the light flashes and turns off. Step 3, turn off the key to complete the process. This reset reminds you to reset the maintenance cycle, and it is recommended to perform this operation after each maintenance to keep the car in good condition. Beginners can easily try it, as the steps are simple and straightforward.

[LaNadia]

To reset the maintenance light, first turn the ignition switch to the ON position without starting the engine. Press and hold the button on the dashboard for about 10 seconds until the light turns off. Pay attention to the indicator changes during the process and avoid pressing the wrong button. A successful reset ensures more accurate timing for the next maintenance interval, helping prevent engine issues. By the way, regular maintenance extends vehicle lifespan—resetting is just the starting point; don’t neglect oil checks. Maintaining overall vehicle condition is key.

[DiKyle]

Reset method for 2020 Emgrand GS maintenance light using button combination. Turn ignition to ON position but do not start the engine. Locate the instrument cluster button and hold it for 5 to 10 seconds to reset. After completion, turn off the ignition to reset the system. Regular reset prevents false alarms and maintains accurate maintenance schedules. This brand's vehicles generally support universal methods; if the light persists, consult the manual or visit a service center. Remember, the maintenance light serves as a reminder for oil changes to ensure optimal engine performance - neglecting to reset may cause unnecessary issues.